About jan.mierczi

jan.mierczi · 12-10-2018

Hi, I am assigned to very interesting case in my company: my mate from VoIP telephony team asked me to determine how many bandwidth is consumed by Skype audio traffic. Let's say I need to know how many bit/s or Mb/s in average and in peak. It will us...

jan.mierczi · 02-01-2018

Hi Community, I am working on deployment and recovering WAAS service in my company. Some of modules were decommissioned in past (site was closed and all equipment moved to central office) some might be new one. Situation. There is a module. ...

jan.mierczi · 07-18-2017

Dear Friends, <BLUF>: How to determine and prove that we need change current 'router-on-the-stick' design on L3 switches solution and move inter-VLAN routing on L3 switches? I am a network specialist and my company rather install small sites with r...

jan.mierczi · 05-20-2017

Hi, I am designing a site and need decide what type VPN use. What VPN type would be better choose so that users and admins leaverage maximum benefits from this design? And why? I uderstand diference between how both work but do not see advantages o...

jan.mierczi · 05-08-2017

Hello, Recently we get many compliants in our company about performance etc. Everybody states that it is somethis wrong with WAAS. We uses SM-SRE-910-K9. I got a case and trying understand if this is refers to SRE or simple another problems. The lo...

jan.mierczi · 12-18-2018

Perfect, thank you! It seems the best reply. However, could you explain me please how can I see output? How can we see results of this "capture"? We use Solarwins Netmon. Currently my router is sending logs like: PL#sh run | sec flow flow expor...

jan.mierczi · 12-10-2018

The second question: how to derive output over there?

jan.mierczi · 12-10-2018

Hi, Thank you for your answer. I saw these articles on Friday. However, I am confused about config. I am missing enough skill to compose config. I would appreciate if you could briefly explain how to compose config for that.

jan.mierczi · 02-12-2018

Hello. I do not know how but finally I managed install SW. The challenge was that installation was stopping for unknown reason. I have placed initial configuration again and somehow SW image deployment started. Thank you

jan.mierczi · 07-18-2017

When you say your company has been implementing router-on-a-stick, do you mean using a L2 switch and a software based (e.g. ISR) router? Yes, I do. ISR, switch L2, sub-interfaces. If so, the simplest criteria you might use if there's any local int...

Member Since	‎05-08-2017 04:17 AM
Date Last Visited	‎07-04-2021 01:13 PM
Posts	11

User Statistics

User Activity

How to measure amount of traffic (bandwidth), consumed by certain application (Skype f.e.) on branch router?

SM-SRE-910-K9 down. Software image is not installing. How to restore "Unable to load image Error: Selected disk does not exist (21)"

How to determine of multi-layer switch is needed?

What would be better choose: C2S or S2S VPN?

Services Module SM-SRE-910-K9 error log and perfomance issue. %WAAS-RE-3-690412: Unknown frame type from peer:

Re: How to measure amount of traffic (bandwidth), consumed by certain application (Skype f.e.) on branch router?

Re: How to measure amount of traffic (bandwidth), consumed by certain application (Skype f.e.) on branch router?

Re: How to measure amount of traffic (bandwidth), consumed by certain application (Skype f.e.) on branch router?

Re: SM-SRE-910-K9 down. Software image is not installing. How to restore "Unable to load image Error: Selected disk does not exist (21)"

When you say your company has