About mR_Slug

mR_Slug · 01-11-2024

Had a working config, router and vdsl modem were fine. Now I get:%VDSL_DAEMON-3-MODEMRESET: VDSL Modem reset. Reloading the modem.%VDSL_DAEMON-3-MODEMRESET: VDSL Modem reset. Reloading the modem.%VDSL_DAEMON-3-MODEMRESET: VDSL Modem reset. Reloading ...

mR_Slug · 12-14-2023

I've followed this https://community.cisco.com/t5/ip-telephony-and-phones/configuring-vic2-2fxs-and-vic2-2fxo-to-make-call-thru-them/td-p/2207237 to get my fxs ports talking to each other, config below. How do i route calls coming in from voip, or a ...

mR_Slug · 11-26-2023

im getting the error "pvc already member of PPPoA dialer pool" when trying to runpppoe-client dial-pool-number 1Basically i accidentally followed the PPPoA method, now trying to correct to pppoe. I'm 1 week into IOS. Got a wap and switch configured,...

mR_Slug · 11-10-2023

OK I have a Cisco AIR-AP1041N-A-K9 Aironet Autonomous Access Point. Basically however i configure it i cant connect to it. I've been following this guide: https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/67134-wpa2-confi...

mR_Slug · 01-15-2024

Thanks everyone. As I understand it i would need to add something along these lines.voice class uri 202 siphost dns:sample.comdial-peer voice 101 voipsession protocol sipv2incoming uri via 202How would i set the above dial peer to ring extension 10, ...

mR_Slug · 01-12-2024

Ah-ha! the dsl.bin file was missing so i copied the image using copy http://location flash0:. Followed these instructions https://www.cisco.com/c/en/us/support/docs/long-reach-ethernet-lre-digital-subscriber-line-xdsl/lre-vdsl-long-reach-ethernet-ver...

mR_Slug · 01-12-2024

Sorry, forgot to post the config. its a 2901 with an EHWIC-VA-DSL-M in slot 3.sh ver:Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.7(3)M7, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1...

mR_Slug · 01-03-2024

Dont suppose someone could assist? I think I'm 50% there. Also how would you route calls to an FXO? I'm assuming you would edit the dial peer with the destination-pattern 9.T declaration, but how to route to FXO?The documentation on cisco stuff is ex...

mR_Slug · 12-21-2023

Thanks. I've been reading this document https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/voice/cube/ios-xe/config/ios-xe-book/m_voi-inbnd-dp-match-uri.html . As I understand it i would need to add something along these lines. There is only one sip s...

Member Since	‎11-10-2023 02:31 PM
Date Last Visited	‎02-14-2024 12:05 AM
Posts	17
Total Helpful Votes Received	1

User Statistics

User Activity

Event 'line_retrain' is invalid for the current state 'boot_init':vdsl

Inbound dial peers, how to route call from voip to extensions.

remove pppoa from pvc because "pvc already member of PPPoA dialer pool

Cant connect to Cisco AIR-AP1041N-A-K9

Re: Inbound dial peers, how to route call from voip to extensions.

Re: Event 'line_retrain' is invalid for the current state 'boot_init':

Re: Event 'line_retrain' is invalid for the current state 'boot_init':

Re: Inbound dial peers, how to route call from voip to extensions.

Re: Inbound dial peers, how to route call from voip to extensions.