Hello guys,   Do you know if I can do an upgrade from an standard 3260 Server without an expander module (to add RJ-45 Ports) to a 3260 server by just adding the expander module? Do I need Cisco to do it or can it be done by a customer/partner? ... View more

Hello guys, this is my first post and I do know I have a lot of questions. If I did something wrong please bear with me and do point me on the right direction so I can fix my wrongs. We currently have VNMC and VSG installed at version 2.0.3f . The customer is looking at doing an upgrade to this software. Also, they are looking at buying two more VNMC/ VSG so they can have High availability. Is that needed or can they have active/pasive like for the Nexus 1000v? After we do the upgrade do they need to re-license? Also, I did notice a message at the upgrade site that says that the software now became Prime Network Services Controller. If I have an active smartnet can I do the upgrade? Or is it so different that it's not allowed. Thank you in advance for any guidance you guys could provide. Greetings, C. ... View more

This is the configuration I have on my vsm !Command: show running-config !Time: Thu Dec 20 02:15:30 2012 version 4.2(1)SV2(1.1) svs switch edition essential no feature telnet banner motd #Nexus 1000v Switch# ssh key rsa 2048 ip domain-lookup ip host Nexus-1000v 172.16.0.69 hostname Nexus-1000v errdisable recovery cause failed-port-state vem 3   host vmware id 78201fe5-cc43-e211-0000-00000000000c vem 4   host vmware id e51f2078-43cc-11e2-0000-000000000009 priv 0xa2cb98ffa3f2bc53380d54d63b6752db localizedkey vrf context management   ip route 0.0.0.0/0 172.16.0.1 vlan 1-2 port-channel load-balance ethernet source-mac port-profile default max-ports 32 port-profile type ethernet Unused_Or_Quarantine_Uplink   vmware port-group   shutdown   description Port-group created for Nexus1000V internal usage. Do not use.   state enabled port-profile type vethernet Unused_Or_Quarantine_Veth   vmware port-group   shutdown   description Port-group created for Nexus1000V internal usage. Do not use.   state enabled port-profile type ethernet vmware-uplinks   vmware port-group   switchport mode trunk   switchport trunk allowed vlan 1-3967,4048-4093   channel-group auto mode on   no shutdown   system vlan 2   state enabled port-profile type vethernet Management   vmware port-group   switchport mode access   switchport access vlan 2   no shutdown   state enabled port-profile type vethernet vMotion   vmware port-group   switchport mode access   switchport access vlan 2   no shutdown   state enabled port-profile type vethernet ServidoresGestion   vmware port-group   switchport mode access   switchport access vlan 2   no shutdown   state enabled port-profile type vethernet L3-VSM   capability l3control   vmware port-group   switchport mode access   switchport access vlan 2   no shutdown   system vlan 2   state enabled port-profile type vethernet VSG-Data   vmware port-group   switchport mode access   switchport access vlan 2   no shutdown   state enabled port-profile type vethernet VSG-HA   vmware port-group   switchport mode access   switchport access vlan 2   no shutdown   state enabled vdc Nexus-1000v id 1   limit-resource vlan minimum 16 maximum 2049   limit-resource monitor-session minimum 0 maximum 2   limit-resource vrf minimum 16 maximum 8192   limit-resource port-channel minimum 0 maximum 768   limit-resource u4route-mem minimum 1 maximum 1   limit-resource u6route-mem minimum 1 maximum 1 interface mgmt0   ip address 172.16.0.69/25 interface control0 line console boot kickstart bootflash:/nexus-1000v-kickstart.4.2.1.SV2.1.1.bin sup-1 boot system bootflash:/nexus-1000v.4.2.1.SV2.1.1.bin sup-1 boot kickstart bootflash:/nexus-1000v-kickstart.4.2.1.SV2.1.1.bin sup-2 boot system bootflash:/nexus-1000v.4.2.1.SV2.1.1.bin sup-2 svs-domain   domain id 1   control vlan 1   packet vlan 1   svs mode L3 interface mgmt0 svs connection vcenter   protocol vmware-vim   remote ip address 172.16.0.66 port 80   vmware dvs uuid "ae 31 14 50 cf b2 e7 3a-5c 48 65 0f 01 9b b5 b1" datacenter-n ame DTIC Datacenter   admin user n1kUser   max-ports 8192   connect vservice global type vsg   tcp state-checks invalid-ack   tcp state-checks seq-past-window   no tcp state-checks window-variation   no bypass asa-traffic vnm-policy-agent   registration-ip 172.16.0.70   shared-secret **********   policy-agent-image bootflash:/vnmc-vsmpa.2.0.0.38.bin   log-level for some reason my vsm can't the the vem. I could before, but then my server crashed without doing a copy run start and when it booted up all my config but the uplinks was lost. When I tried to configure the connection again it wasn't working. I'm also attaching a screen capture of the vds and a capture of the regular switch. I will appreciate very much any help you could give me and will provide any configuration details that you might need. Thank you so much. ... View more