About rafael_rung

rafael_rung · 05-24-2011

Hello,i have a issue with IP Version 6 and Zone-Based-Policy-Firewall.this is the setup:Router1 (Cisco 1802, IOS 15.1(3)T1, i also tried older IOS): #######Dialer 0 to IPV4 InternetDialer 6 to IPV6 InternetTunnel 0 configured as DMVPN to Router 2VLAN...

rafael_rung · 11-04-2010

Hello,we ordered several additional Cisco ATA 186 for our Customer, but we received the new ones (ATA 187).now i have problems with the callerid. no matter what i configure unter the Caller id Configuration (CUCM 8.0(3)) my phone does not display any...

rafael_rung · 10-04-2010

Hello,we have CUCM8.0(3) with a SIP Trunk to our Provider. For outbound and inboud calls it works fine, but we have problems with call forwarding.when the cucm sends an invite packet out to reach the call forward destination, it sends in the PAI Fiel...

rafael_rung · 09-20-2010

Hello,i have a big Problem with our VG202's.We have CUCM 8.0(2) with a SIP Trunk to our Telephone Provider.with the VG202 i tried IOS 12.4.22T5 and 15.0.1M3.When i connect a Analog Phone to the FXS Port, everything works fine.i can phone out and in.W...

rafael_rung · 03-30-2010

Hello,i have an cisco 1802 with IOS 12.4(15)T12.i configured CBWFQ for the outgoing direction of the dialer 0 interface and everything works fine.but i have also a problem with too much traffic coming in on dialer 0 so i tried to configure a policing...

rafael_rung · 07-09-2011

Hello Phillip, thank you for your answer. i also think that this is a bug, but until now i have this problem only in my test lab and i don't think that cisco is happy if i open a case without a customer that is affected. so i downgraded the ios to a ...

rafael_rung · 05-27-2011

Hello Mike,thanks for the answer,for my first test thedebug policy-firewall detailcommand killed all my connections (ssh, vpn and so on) for some minutes so i will try it another time with a physical console cable attached.Rafael

rafael_rung · 11-11-2010

Hello skr,i'm sorry but in our constellation we did not use a cube. we wanted to do that but it was to expensive. we do not have a sip provider in the internet, the provider is in our mpls solution included so there is no need of a cube.and so we ope...

rafael_rung · 11-08-2010

well i got the Caller id working.the problem is that my test phone, which i use to test this feature also on other pbx systems and which did a great job all the time and which also displays callerid on the vg202 and ata 186 does not display the calle...

rafael_rung · 10-08-2010

Hello Phillip,well that's true, but our provider thinks that if a call is forwarded, the PAI Header should include the complete Number of the line / phone that did the call forwarding, not the number of the caller. and as i read the description from ...

Member Since	‎03-08-2007 11:02 AM
Date Last Visited	‎08-18-2017 03:55 AM
Posts	20
Total Helpful Votes Received	4

User Statistics

User Activity

ZBPF IPV6 Problem

Cisco ATA 187 and the Caller id, Call Forward All

CUCM 8.0(3) Modify PAI and Diversion Header for SIP Trunk

Cisco VG202 (MGCP) Fax Problem with CUCM 8.0(2) and Sip Trunk

incoming Qos for Dialer interface

Re: ZBPF IPV6 Problem

Re: ZBPF IPV6 Problem

Re: Cisco VG202 (MGCP) Fax Problem with CUCM 8.0(2) and Sip Trun

Re: Cisco ATA 187 and the Caller id, Call Forward All

Re: CUCM 8.0(3) Modify PAI and Diversion Header for SIP Trunk