About sisal

sisal · 01-31-2008

Hello, To check the status of spanning-tree on the ports of my switches (on vlan1), I do an snmpwalk on object dot1dStpPortState (1.3.6.1.2.1.17.2.15.1.3) of BRIDGE-MIBsnmpwalk -v 2c -c public myhost 1.3.6.1.2.1.17.2.15.1.3SNMPv2-SMI::mib-2.17.2.15.1...

sisal · 12-10-2007

The HDLC T1 leased line that we use to connect to a partner's site, has always been working fine. Recently, in several occasions, some Telco's problems brought the protocol down on our serial interface, but the remote partner's serial interface didn'...

sisal · 02-22-2005

I've been using for years a Virtual-Template to activate a permanent ppp multilink bundle between 2 sites (virtual access interface is dynamically created at router boot and stays active forever).Once defined the "multilink Virtual-Template 1", it is...

sisal · 09-13-2004

I would like to enhance the connectivity of our mobiles (now via GSM), allowing also a GPRS connection. The existing GSM infrastructure (3 NAS working with Radius/Oracle) should be retained as a backup in the case of GPRS network problems. Our teleco...

sisal · 01-30-2004

I have a dialer pool with 4 members (BRI0/0, BRI0/1..) and 4 dialer profiles (dialer1,dialer2...).I would like to configure the router in a way that EVERY DIALER HAS ITS OWN PREFERRED BRI but can use other bri if necessary.Dialer1 should use bri0/1, ...

sisal · 02-04-2008

You are correct. Getting dot1dBasePortIfIndex for the PORT-ID (in my previous example 40 and 48), I retrieve the ifIndex and as a consequence ifDescr.Thank you.

sisal · 12-11-2007

Thank you for your reply. YES: I confirm that neither CSU/DSU is in a looped state, and Telco can loop both CSU/DSUs. However CSU/DSUs are external boxes owned and managed by TELCO and connected to the routers via Serial Interfaces (our is a WIC-1T: ...

sisal · 02-25-2005

THINGS ARE NOT SO OK.......I've discovered that the "ppp multilink group n" supported by a Virtual-Interface, still needs an interface Multilink n definition!!! So I did not define a second Virtual-Interface and I left the interface Multilink definit...

sisal · 09-22-2004

Is it a guess or are you SURE of it? And in this case, how could I maintain the same IP address on the mobile and connect to it via GSM if the GPRS link could not be estabilished?I thought of SOURCE ROUTING but I don't know how to implement it in the...

sisal · 07-19-2004

I confirm the (great!!) value of MRTG.here are some further info from Cisco:How to Collect CPU Utilization on Cisco IOS Devices Using SNMP:http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a94.shtml

Member Since	‎07-22-2003 01:35 AM
Date Last Visited	‎08-18-2017 03:50 AM
Posts	26
Total Helpful Votes Received	5

User Statistics

User Activity

Bridge OID's indexed by different ifIndex values?

Protocol both up and down at the 2 ends of a leased line?

2 Permanent PPP multilinks: Virtual-Template + Interf. Multilink: is it OK?

Can I get routes of active GPRS mobiles from telco's GGSN?

Binding dialers to specific BRI using a single pool

Re: Bridge OID's indexed by different ifIndex values?

Re: Protocol both up and down at the 2 ends of a leased line?

Re: 2 Permanent PPP multilinks: Virtual-Template + Interf. Multi

Re: Can I get routes of active GPRS mobiles from telco's GGSN?

Re: Want to monitor Router CPU Utili. using SNMP.