Alright, Thanks. Going to try that. ... View more

So if I understand this correctly, I need 3 dial-peers in total for the onramp fax? Onramp fax: dial-peer voice 2000 pots description Binnenkomende gespreken ISDN service onramp incoming called-number 765724099 direct-inward-dial port 0/0/0 dial-peer voice 2001 pots description Binnenkomende gespreken ISDN service onramp incoming called-number 765724038 direct-inward-dial port 0/0/0 dial-peer voice 2002 pots description Binnenkomende gespreken ISDN service onramp incoming called-number 765724039 direct-inward-dial port 0/0/0 Normal calls(DP 2003 - .....) dial-peer voice 2003 pots description Binnenkomende gespreken ISDN incoming called-number .T direct-inward-dial port 0/0/0 Is this a correct configuration? Also, what about the port . Can I use port 0/0/0  for all 3 onramp dial-peers? Thanks, ~Grant ... View more

Lets say I want to use 765724099, 765724038, 765724039 as my faxing numbers and each of them having a different emailbox. Have those 3 numbers use dial-peer voice 2000 pots and have the rest of the telephonenumbers we have go through the other dial-peers. Thanks, ~Grant ... View more

Just tried something. When dial-peer voice 2000 pots is configured the following way: dial-peer voice 2000 pots description Binnenkomende gespreken ISDN service onramp incoming called-number 765724099 direct-inward-dial port 0/0/0 It works just fine. Incoming ISDN calls work fine. As soon as I configure dial-peer voice pots the following way: dial-peer voice 2000 pots description Binnenkomende gespreken ISDN service onramp incoming called-number .T direct-inward-dial port 0/0/0 Like this, incoming ISDN calls fail. We have 3 numbers that will use the onramp faxing. I thought if I configure .T on dial-peer voice 2000 pots, the router would recognize the call as fax and use that dial-peer etc. Guess I was wrong. The 3 numbers that will be used for onramp fax all begin the following way: 7657240xx . How can I do this? Thanks, ~Grant ... View more

Alright. I stumbled upon a major issue here. Once serivce onramp is configured on dial-peer voice 2000 pots, people aren't able to reach us anymore. debug isdn q931 gives the following output: 000213: *Dec 25 23:16:28.779 WEST: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/1/0, TEI 0 changed 000214: *Dec 25 23:16:28.831 WEST: ISDN BR0/1/0 Q931: RX <- SETUP pd = 8  callref = 0x55         Sending Complete         Bearer Capability i = 0x8090A3                 Standard = CCITT                 Transfer Capability = Speech                 Transfer Mode = Circuit                 Transfer Rate = 64 kbit/s         Channel ID i = 0x81                 Preferred, B1         Calling Party Number i = 0x2181, '618016387'                 Plan:ISDN, Type:National         Called Party Number i = 0xA1, '765724030'                 Plan:ISDN, Type:National         High Layer Compat i = 0x9181 000215: *Dec 25 23:16:28.839 WEST: ISDN BR0/1/0 Q931: TX -> CALL_PROC pd = 8  callref = 0xD5         Channel ID i = 0x89                 Exclusive, B1 000216: *Dec 25 23:16:28.855 WEST: ISDN BR0/1/0 Q931: TX -> DISCONNECT pd = 8  callref = 0xD5         Cause i = 0x8081 - Unallocated/unassigned number 000217: *Dec 25 23:16:29.087 WEST: ISDN BR0/1/0 Q931: RX <- RELEASE pd = 8  callref = 0x55         Cause i = 0x8081 - Unallocated/unassigned number 000218: *Dec 25 23:16:29.087 WEST: ISDN BR0/1/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xD5 I also did a debug voip ccapi inout and saw when service onramp was configured that the calls always went through dial-peer voice 2000 pots which had the service onramp configured on it. We have 3 more dial-peer voice pots configured for incoming ISDN calls. This is the config WITH onramp configured. But I took it out for now, because we need to be reachable for our customers. dial-peer voice 2000 pots description Binnenkomende gespreken ISDN service onramp incoming called-number .T direct-inward-dial port 0/0/0 ! dial-peer voice 2001 pots description Binnenkomende gespreken ISDN incoming called-number .T direct-inward-dial port 0/0/1 ! dial-peer voice 2002 pots description Binnenkomende gespreken ISDN incoming called-number .T direct-inward-dial port 0/1/0 ! dial-peer voice 2003 pots description Binnenkomende gespreken ISDN incoming called-number .T direct-inward-dial port 0/1/1 How can I configure this so that it works with service onramp? I'm thinking the issue lies with DID, not sure tho. Not an expert Thanks, ~Grant ... View more

My bad. It was already working. I was skipping through the pages the wrong way with the default windows viewer. But I guess those commands won't hurt my config. So I'll just leave them in. Thank you for your help! Really appreciate it. ... View more

Rated. Now the next problem occured. When I fax multiple pages, only the first one is shown in the TIFF file. Any idea what might cause that? ... View more

Thanks for the reply. Good to know that RADIUS isn't needed. But I fixed it. It's working now.First I enabled debug fax mta all and went through it step by step and I saw: 007330: *Dec 24 14:29:45.165 WEST: //-1/F762056680C4/SMTPC/esmtp_client_engine_work_routine:    error in response to MAIL FROM I added the mta send mail-from hostname WORD command and it worked ... View more

If the problem lies with AAA, can't onramp faxing be configured without using AAA and a RADIUS server? ... View more