Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Momodou lamin Manneh
08-18-2017
Momodou lamin Manneh
Member since
06-29-2010
Beginner
12-31-2015
04:43 AM
Hello Casanavep,
Thanks for the help.With the default settings i can't read the text .I used the inbuilt-in RS232.The console cable is OK.
... View more
12-30-2015
11:36 AM
Hello pwwiddicombe,
Thanks for that guide lines.I have tried the default config(9600) but to no avail.I will give guide #2 a try .
3.There is no telnet/ssh configured .The was never any configuration done on it .
I tried setting the switch to default configs but still seeing the same characters.
Is it possible to boot it to ROMMON mode with this ?
©g¿ýwo;sÚ÷Ûg×ë¥_o½ÿ²rßÿ}ÒýmÿÝʺmÝ·õû½Ò~¶²{ïm»ëóoÚwïïw{ç׿ëk¿~Úîm{¶ï¿ºÛûm·»Ûï÷·ýçZ5Ú{¶õm÷uëi·ówïsÚoûm{oé»ÿÚ™ûÛvÛ½ù½{ó²å}¿ýeþÛïuÛõŸ¶û·»¿nÛºéûÊmÿm¿þn·ºwo¿³m_³¯÷ËóSîí{íÛßn÷ßks￯ûÝú{îÖ¿ånîÝeõóÿß
Thanks for your help.
... View more
12-30-2015
05:18 AM
I used both secureCRT and hyperterminal.........
With the following details.......
COM ----- 1
Baud rate ------ 9600
Data bits ----- 8
Parity ------ None
Stop bit ------ 1
I think this is default configs
... View more
12-30-2015
04:55 AM
Hello Zdesingstudio,
Thanks for your reply but am very sure that the console cable is working perfectly good and i have change the baud rate from 110 all the way to 115200 still having thesame garbage....
I always have error whenever i use baud rate above 115200
... View more
12-30-2015
01:49 AM
Hello All,
Issue with Cisco switch 2960.This device is less than 6months old in my network(though never connected on it through console) and one fine day
we wanted to configure a vlan on it but to our surprise the console connection only give us some funny characters.Going through Cisco forum,i came
across a similar problem .Mr.Leo mention changing baud rate setting to different values and that was helpful to some people.For my case, i change baud rate setting from 110 to 115200 am still having thesame garbage.
ÝäÖ¾å±÷7²Þ·so½lþþù·òvŸÏrû;æk¦üýÿsç¦ßwdûëÿtÝÏþó¾ï{¶º¾eÖù~ÿÝmþnóï›ÿþo·oï~ÝýÿoÖæmþ¶Ÿ¤ÿùe·ùÛ×?îŠíü¬þßÛþûÜóî÷w¿ÌYÿîrfÛ7tzûûÛYÞ޵߷»Ï–õs~þoùÖý]vÛݹfºúwæm¾ýºùnÿ3oïîîúoõ»ó¾ûÿ·r¾{eíÿ·#¾ëo»Ûÿû:ÖÏ…ÝfÔþåþþÿÖgþówå¹fóoùwgÖ{óo·ÿrkNÛ÷_߻ߒÿoë·Ú¾¿rw·ºoúÒöjõ²ûî¿þÛû¶vçß¿[}[ÛŸóÛÿïÒgoù}¿g¿r_ùuw¿nÿÝß;-ߦóïõí¿ïÖùïnÿ7·êYÛïsf»¿g;ÿÛßÙÙúµÿw+KË[;~éÛþé»ïÒå·þu÷2ºëç2m¾ù~éwþ)gÛ›^o¶ßnnºûÿ¿k¾ý{ýïÛo¾{oóÿß߶þÙísfêíån~~fÝ¿ûwåý©g¿ýwo;sÚ÷Ûg×ë¥_o½ÿ²rßÿ}ÒýmÿÝʺmÝ·õû½Ò~¶²{ïm»ëóoÚwïïw{ç׿ëk¿~Úîm{¶ï¿ºÛûm·»Ûï÷·ýçZ5Ú{¶õm÷uëi·ówïsÚoûm{oé»ÿÚ™ûÛvÛ½ù½{
Is there any other way out of this issue ?
Thanks in advance
... View more
Labels:
10-26-2015
08:30 AM
Hello Leo, Thanks for sharing the page.Anyway am still trying to get it right the difference between shaping and limiting.My own issue is LIMITING traffic to the subscribe bandwidth. ASR1002 connected to cisco 3560 this connecting all the ethernet customers.i want to apply rate limit on each sub-interface for every customers. See two configuration sample i applied on the router for a customer connected on 10Meg but its not working. Policy Map policy10 Class police police cir 10240000 bc 10240000 pir 10240000 be 10240000 conform-action transmit exceed-action set-prec-transmit 2 violate-action drop int gi q/w/e.123 service-policy input policy10 service-policy output policy10 Policy Map police Class Group10 police cir 10240000 bc 10240000 be 10240000 conform-action transmit exceed-action drop violate-action drop . int gi a/s/d.246 service-policy input police service-policy output police Am i missing something or not doing it right. Please help.
... View more
10-23-2015
11:13 AM
Hello........ Still on the issue of ASR. It was configured and integrated on the production network.i have a problem of limiting bandwidth for customers.Need help for configuring a dedicated bandwidth for customers.Example : configuring a dedicated 1Mbps for a customer. Thanks in advance....
... View more
Labels:
10-16-2015
10:04 AM
Hi... After going through that tedious testings, i came to the conclusion that the issue was on the fibre jumper i was using.There are two different fiber jumper(all SMF) provided by two different companys/providers.One of the providers' fiber will always show interface UP protocol UP on the ASR1002-X and interface UP and protocol down on any other router(7200 or 7600) connected to ASR1002-x with a poor reliability. Getting that fiber from our old provider , and testing that with the ASR and the 7200 and 7600,it was realized that certain type of fibre (both MMF and SMF) doesn't work with the ASR. With the old fiber, the ASR is now integrated into the production network. Thanks Vinit.
... View more
10-11-2015
11:18 AM
Hi Vinit, i a have VERY interesting scenario.I dont know what kind of MAGIC happens.When i did the loopback test to toward the 7200,the interface show UP UP.I left the test on(for about 30 mins or so) while doing other things. After reading your last post,i normalized the connection.to my suprise,the interface came up without changing nothing....... Router#sh int g0/3 GigabitEthernet0/3 is up, line protocol is up Hardware is BCM1250 Internal MAC, address is 0018.7384.f419 (bia 0018.7384.f419) Description: **** TO ASR ***** Internet address is 10.10.10.1/30 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, link type is force-up, media type is LX output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:43:09, output 00:00:08, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 313 packets input, 32218 bytes, 0 no buffer Received 53 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 56 multicast, 0 pause input 0 input packets with dribble condition detected 995 packets output, 106667 bytes, 0 underruns 7 output errors, 0 collisions, 3 interface resets 0 babbles, 0 late collision, 0 deferred 7 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out Router#ping 10.10.10.2 rep 100 Type escape sequence to abort. Sending 100, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Success rate is 100 percent (100/100), round-trip min/avg/max = 1/1/4 ms Router# Am currently doing a similar test with a different gbic,spf and fibre cable. Thanks for your help.
... View more
10-11-2015
09:20 AM
I also realised thesame thing .On the ASR its 255/255 and on the 7200 , reliability 136/255, txload 1/255, rxload 1/255. Which is interesting . is not passing through a patch panel .Is direct fibre cable . i tried doing a test by isolating the ASR and doing a loopback.See the ouput: Router#sh int g0/3 GigabitEthernet0/3 is up, line protocol is up Hardware is BCM1250 Internal MAC, address is 0018.7384.f419 (bia 0018.7384.f419) Description: **** TO ASR ***** Internet address is 10.10.10.1/30 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, link type is force-up, media type is LX output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:04, output 00:00:04, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 16 packets input, 1878 bytes, 0 no buffer Received 13 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 5 multicast, 0 pause input 0 input packets with dribble condition detected 153 packets output, 20062 bytes, 0 underruns 6 output errors, 0 collisions, 3 interface resets 0 babbles, 0 late collision, 0 deferred 6 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
... View more
10-11-2015
09:05 AM
Hello Vinit, thanks for your swift response. I now connected the ASR to a Cisco 7206 G1 with the same Gbic module still thesame result. Here s the output form the Cisco 7206: GigabitEthernet0/3 is down, line protocol is down Hardware is BCM1250 Internal MAC, address is 0018.7384.f419 (bia 0018.7384.f419) Description: **** TO ASR ***** Internet address is 10.10.10.1/30 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 136/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 1000Mb/s, link type is force-up, media type is LX output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:01:28, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 13 packets output, 4572 bytes, 0 underruns 5 output errors, 0 collisions, 3 interface resets 0 babbles, 0 late collision, 0 deferred 5 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out this is the output from the ASR ASR1002#sh int g0/0/3 GigabitEthernet0/0/3 is up, line protocol is up Hardware is 6XGE-BUILT-IN, address is 0462.7380.1403 (bia 0462.7380.1403) Description: *****TO 7206 ***** Internet address is 10.10.10.2/30 MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set Keepalive not supported Full Duplex, 1000Mbps, link type is force-up, media type is LX output flow-control is on, input flow-control is on ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:37, output 00:00:41, output hang never Last clearing of "show interface" counters never Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 516 packets input, 52275 bytes, 0 no buffer Received 1 broadcasts (0 IP multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 81 multicast, 0 pause input 954 packets output, 61251 bytes, 0 underruns 0 output errors, 0 collisions, 7 interface resets 74 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out
... View more
10-11-2015
08:33 AM
Hi All Recently acquired a new ASR 1002 to replace my PE router(cisco 7206 G2 engine).The old cisco 7206 was connecting to cisco 7609 which is the gateway router with no problem. After replacing the ASR 1002 with cisco 7206,the link connecting to the gateway router (Cisco 7609) never came up. Is there any special SFP or GBIC module needed to interconnect this two nodes ? On the ASR, am using GLC-LH-SM and on the other side is GBIC module (WS-G5486-C) The directly connected interfaces show diifferent output.The ASR will show interface UP protocol UP while the 7609 will show interface DOWN and protocol DOWN. What am i missing ? Please help.
... View more
Labels:
10-08-2013
05:52 AM
Hello Technical.... I have a new Cisco AS5330 ,thought very OLD to some people that i want to use as a dialup server.I want to transfer the config from my dialup server to the new AS5330 but some parameters are not supported by the AS5330. command like : modem startup-test modem country mica e1-default modem recovery threshold 100 modem recovery action none Without these commands, will the dialup server work ? Want to know before changing . Please help.. Manneh
... View more
Labels:
12-17-2010
05:47 PM
Hello Seniors, I was trying to establish a site-to-site vpn ( crypto isakmp policy configuration) using a cisco 1841 router.I realised that the router (1841) is not supporting the configuration. We decided to enchance the router by the addition of a security module(AIM VPN SSL) but to our suprise,it cannot still support the crypto configuration. When i inserted the module into the router,i did'nt realised any change "say a new hardward found." Can any one help configure this card. This is the show version of my router. Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(3i), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Wed 28-Nov-07 18:17 by stshen ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1) Gamcel-Kairaba uptime is 17 hours, 4 minutes System returned to ROM by power-on System image file is "flash:c1841-ipbase-mz.124-3i.bin" Cisco 1841 (revision 7.0) with 114688K/16384K bytes of memory. Processor board ID FHK1242203X 2 FastEthernet interfaces DRAM configuration is 64 bits wide with parity disabled. 191K bytes of NVRAM. 31360K bytes of ATA CompactFlash (Read/Write) Configuration register is 0x2102 I thank you in advance for your help.
... View more
Labels:
11-23-2010
03:38 AM
Hello All, I found myself in a very serious stituation.My Cisco 1812 router is not booting proper.Any time i put it on,it only shows this "System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2006 by cisco Systems, Inc." Thats all i see on the hyperterminal. Can any one help me get out of this stituatioin ? I thank you in advance in for your contribution.
... View more
Labels:
12-31-2015 04:43 AM
Hello Casanavep, Thanks for the help.With the default settings i can't
read the text .I used the inb...
12-30-2015 11:36 AM
Hello pwwiddicombe, Thanks for that guide lines.I have tried the default
config(9600) but to no avai...
12-30-2015 05:18 AM
I used both secureCRT and hyperterminal......... With the following
details....... COM ----- 1 Baud ...
12-30-2015 04:55 AM
Hello Zdesingstudio, Thanks for your reply but am very sure that the
console cable is working perfec...
12-30-2015 01:49 AM
Hello All, Issue with Cisco switch 2960.This device is less than 6months
old in my network(though ne...
10-26-2015 08:30 AM
Hello Leo,Thanks for sharing the page.Anyway am still trying to get it
right the difference between ...
10-23-2015 11:13 AM
Hello........ Still on the issue of ASR. It was configured and
integrated on the production network....
10-16-2015 10:04 AM
Hi...After going through that tedious testings, i came to the conclusion
that the issue was on the f...
10-11-2015 11:18 AM
Hi Vinit,i a have VERY interesting scenario.I dont know what kind of
MAGIC happens.When i did the lo...
10-11-2015 09:20 AM
I also realised thesame thing .On the ASR its 255/255 and on the 7200 ,
reliability 136/255, txload ...
10-11-2015 09:05 AM
Hello Vinit,thanks for your swift response.I now connected the ASR to a
Cisco 7206 G1 with the same ...
10-11-2015 08:33 AM
Hi All Recently acquired a new ASR 1002 to replace my PE router(cisco
7206 G2 engine).The old cisco ...
10-08-2013 05:52 AM
Hello Technical....I have a new Cisco AS5330 ,thought very OLD to some
people that i want to use as ...
12-17-2010 05:47 PM
Hello Seniors,I was trying to establish a site-to-site vpn ( crypto
isakmp policy configuration) usi...
Public Statistics
| Date Registered | 06-29-2010 10:30 AM |
| Date Last Visited | 08-18-2017 03:55 AM |
| Total Messages Posted | 13 |
| Total Helpful Votes Received | 5 |
.jpg "Hall of Fame Guru"){kind=icon}
