About maghisi-2007

maghisi-2007 · 11-10-2009

I've one cisco 72xx series with some 8 V35 serial ports. If I run, for example, the command sh controller s1/0 I can exactly get the line speed of the PTT csu/dsu connected to this serial port.The same command, used on any kind of router different th...

maghisi-2007 · 11-04-2009

I've a cisco 1841 IOS c1841-spservicesk9-mz.124-5b.bin whose serial ports are connected to a couple of leased lines. One connection (it's the same if I connect it to s0/0/0 or to s0/0/1) after minutes or hours of good work can drop with the router se...

maghisi-2007 · 10-12-2009

Isdn backup layer 2 is constantly invoked with no reason for me as per local PTT main line is working perfectly.By activating debug dialer events and debug isdn events, I can't get relevant informations.I attached sh ver/sh run/debug resultsThanksOct...

maghisi-2007 · 08-28-2008

Cisco 2811.2 FastEthernet interfaces5 ATM interfaces4 Channelized E1/PRI ports1 Virtual Private Network (VPN) Module1 ATM/Voice AIMIOS c2800nm-advipservicesk9-mz.124-5a.binI'm going on getting the alarm reported.Ptt never found troubles.I'm attaching...

maghisi-2007 · 03-07-2008

I've a Call Manager 4.2(3)formed by a cluster composed by a Publisher and a Subscriber. I can get access to both the server, but when I am into the subscriber I cannot, for example, show the list of the phone by getting the following error message: "...

maghisi-2007 · 11-05-2009

After that yesterday PTT rerouted the link to a new path between A-end and B-end, circuit came up and it has been perfectly working till yesterday evening. So, it was a line issue. Very strange problem as csu/dsu never showed any loop condition but t...

maghisi-2007 · 11-04-2009

Shut no shut can restart the connection but it didn't always work and it never completely fixed the trouble. After having replaced the csu/dsu at A-end and B-end, now PTT has rerouted the link to a new path and it's about 1 hour it's working fine, bu...

maghisi-2007 · 10-14-2009

Ok thanks for all your efforts. Excuse me once again for mine previous errors. For me this conversation has been successfully closed

maghisi-2007 · 10-14-2009

Excuse me for the rating system. I didn't want to be unfair. I do not often use cisco forum and I was thinking that I should give you the best rating just at the end of the conversation. Now I know I can give you the best rating at any time. When you...

maghisi-2007 · 10-14-2009

Just to try I activate anyway debug bri:Oct 14 11:32:56: BRI0/1/0: In state F3, Received code Activate request downstream, Info 2 receivedOct 14 11:32:56: BRI0/1/0 : changing state to F6Oct 14 11:32:56: BRI0/1/0: In state F6, Received code Activation...

Member Since	‎07-20-2007 02:37 PM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	39
Total Helpful Votes Received	5

User Statistics

User Activity

Sh controller or any other command able to exactly show the line speed

1841 serial port which is showing an unexisting loopback condition

Isdn invoked with no apparently reason

ATM_AIM-5-CELL_ALARM_UP: Interface ATM0/0/0 lost cell delineation

CCM 4.2(3) Failed to create ASP object

Re: 1841 serial port which is showing an unexisting loopback con

Re: 1841 serial port which is showing an unexisting loopback con

Re: Isdn invoked with no apparently reason

Re: Isdn invoked with no apparently reason

Re: Isdn invoked with no apparently reason