About Nuno Filipe Alves Ferreira

Nuno Filipe Alves Ferreira · 05-28-2010

Hello all,I have an environment where currently I have a UCS System with 2 ESX hosts on it.One of the hosts has a VSM and it is added into the Nexus 1000v dVS (I still have one physical interface on the vswitch with Service Console, VMotion, VSM LANS...

Nuno Filipe Alves Ferreira · 04-30-2010

Hello,I have a blade server with the PALO (VIC) adapter and I am testing the VN-Link in hardware feature ...I have configured everything as per the Cisco UCS Configuration Guide - VN-Link Configuration sectionOn the ESX host I can see the 2 vNICs I c...

Nuno Filipe Alves Ferreira · 03-02-2010

Hello all,I have a project to interconnect 2 DC's using one existing fibre (Pair actually).The 2 DCs are less than 50 km awayWe would like to have dual 4Gbps Fibre Channel for our SAN and dual 1Gbps EthernetI was thinking in the below kit to achieve ...

Nuno Filipe Alves Ferreira · 06-10-2009

Hello all,As mentioned above i have a requirement to connect our current OCS infrastructure to our local PBX (Nortel BCM50).Now the BCM50 doesn't have v3 of the firmware which would allow it to establish a direct sip trunk to the OCS server and it on...

Nuno Filipe Alves Ferreira · 05-31-2009

Hello all,I have 2 routers (cisco 2621XM and 1841) and want to use one of them with the ISDN card (WIC 1B S/T) for PSTN Breakout. My idea is to create a SIP gateway on the router and then the ISDN card to the PSTN and use it as a gateway of the SIP d...

Nuno Filipe Alves Ferreira · 02-28-2011

CorrectNuno Ferreira

Nuno Filipe Alves Ferreira · 02-24-2011

A NAS Apliance connected to the UCS WILL be accessible from the outside world if the UCS system is connected northbound to your LAN and the VLANS on the NAS are also going Northbound ....So, assuming you have the correct routing and switching in plac...

Nuno Filipe Alves Ferreira · 01-17-2011

Hi Dan, You can't cross them. IOM A needs to connect to FI A and IOM B needs to connect to FI B. You can use 1, 2 or 4 cables to connect.Nuno Ferreira

Nuno Filipe Alves Ferreira · 11-22-2010

Well ... Technically you are correct ...The thing is .. if you want to call your solution a vBlock 0, 1 or 2 you have to have the components has per EMC Architecture ... or else you wont be able to call it vBlockI know this because I just delivered o...

Nuno Filipe Alves Ferreira · 10-19-2010

Manish, I was not aware of the FCoE so are you saying that I will be able to connect my Storage Array (Target) on the 10GE ports and run FCoE from it to the FICs ? IF this is the case then: 1 - Do I still require the FC module on the FICs...

Member Since	‎02-28-2008 05:42 PM
Date Last Visited	‎03-03-2021 04:09 AM
Posts	97
Total Helpful Votes Received	11

User Statistics

User Activity

Nexus 1000v and UCS PALO

UCS VIC (PALO) - Associate a host

DC Extension using CWDM Chassis

SIP (OCS) - 2801 (IP-to-IP GW) - Nortel BCM50 (H.323)

WIC 1B S/T and SIP

Re: Direct connect NFS/CIFS with 1.4

Re: Direct connect NFS/CIFS with 1.4

Re: IOM to Interconnect link

Re: Vblock 0

Re: Vblock 0