Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About gb-fairchild
08-18-2017
Stats
Member since
04-18-2008
74
Posts
10
Helpful
0
Solutions
01-11-2013
06:22 PM
Did you ever figure this out?? I have one remote site that reports periodic drops. TAC has not been able to find anything. CUCM 7.1.3 GWay is 2951 running C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
... View more
Created by
gb-fairchild
in IP Telephony and Phones
in IP Telephony and Phones
10-05-2012
04:15 PM
10-05-2012
04:15 PM
We are replacing a Mitel PBX at one of our sites with call manager and a 2951 router as an MGCP gateway. They have seperate paging amps and Bogen TAM-B units for upstairs and downstairs paging. I have paging working using FXO ports configured for loop start and a route pattern to each port. So I can page upstairs or downstairs by dialing the desired route pattern - in my case 71 for downstairs and 72 for upstairs. Is there a way to page both upstairs and downstairs at the same time? Kind of like a hunt group with the distribution algorithm set to broadcast. I know we can get different hardware and use tones to do it but just wondering if it can be done with existing hardware. Apparently the Mitel system could do it.
... View more
Labels:
Created by
gb-fairchild
in IP Telephony and Phones
in IP Telephony and Phones
06-28-2012
04:40 PM
06-28-2012
04:40 PM
We have call Manager 7.1.3, MGCP gateway on Cisco 2811 running IOS Version 12.4(25b), with SRST configured My question: If a user at the remote site is on an external call to the PSTN and the gateway looses its connection to Call Manager the gateway and phones go into SRST fallback. Will this call be dropped? Phone ---------2811 with SRST----------T1 PRI------------PSTN--------Phone | X | CUCM Subscriber
... View more
- Tags:
- cucm
- mgcp_gateway
- srst
Labels:
02-09-2012
05:45 PM
Here is the solution(from Cisco TAC): There are two mutlilink's on this router. Both were using the local endpoint discriminator of Ply2811MPLS. This caused a problem when trying to add an interface to the new multilink(multilink3). We added a local endpoint discriminator of cisco123 to the new serial interfaces: This first – to find an available extension: interface Serial0/2/0:0 no ip address encapsulation ppp fair-queue ppp multilink ppp multilink group 3 ppp multilink endpoint string cisco123 Then they could be added to multilink3 Ply2811MPLS#sh ppp multilink Multilink3 Bundle name: group147520 Remote Endpoint Discriminator: [1] group147520 Local Endpoint Discriminator: [1] cisco123 Bundle up for 08:55:00, total bandwidth 7680, load 1/255 Receive buffer limit 60000 bytes, frag timeout 1000 ms 0/0 fragments/bytes in reassembly list 0 lost fragments, 0 reordered 0/0 discarded fragments/bytes, 0 lost received 0x111 received sequence, 0x124 sent sequence Member links: 5 active, 0 inactive (max not set, min not set) Se0/2/0:0, since 08:55:00, 5760 weight, 1496 frag size Se0/0/1:0, since 08:47:22, 5760 weight, 1496 frag size Se0/2/1:0, since 08:46:13, 5760 weight, 1496 frag size Se0/3/1:0, since 08:45:53, 5760 weight, 1496 frag size Se0/3/0:0, since 08:45:41, 5760 weight, 1496 frag size Multilink1 Bundle name: group18540 Remote Endpoint Discriminator: [1] group18540 Local Endpoint Discriminator: [1] Ply2811MPLS Bundle up for 2w1d, total bandwidth 4608, load 63/255 Receive buffer limit 36000 bytes, frag timeout 1000 ms 0/0 fragments/bytes in reassembly list 688 lost fragments, 39707171 reordered 0/0 discarded fragments/bytes, 0 lost received 0x60E223 received sequence, 0xDD93E1 sent sequence Member links: 3 active, 0 inactive (max not set, min not set) Se0/1/1:0, since 2w1d Se0/0/0:0, since 2w1d Se0/1/0:0, since 6d08h Thanks - Bill
... View more
02-06-2012
06:40 PM
Thanks for looking at this. I changed the mtu size as you suggested. Still no luck. It looks ok until this message: Feb 7 02:07:32.307: Se0/2/0:0 MLP: cdp packet forwarded to wrong interface Then it goes ahead and drops the link from the bundle and then starts all over again. Debug: Feb 7 02:07:30.307: Se0/2/0:0 PPP: Phase is ESTABLISHING, Passive Open Feb 7 02:07:30.307: Se0/2/0:0 LCP: State is Listen Feb 7 02:07:30.323: Se0/2/0:0 LCP: I CONFREQ [Listen] id 19 len 28 Feb 7 02:07:30.323: Se0/2/0:0 LCP: MagicNumber 0xC57F0DCD (0x0506C57F0DCD) Feb 7 02:07:30.323: Se0/2/0:0 LCP: MRRU 1500 (0x110405DC) Feb 7 02:07:30.323: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 7 02:07:30.327: Se0/2/0:0 LCP: O CONFREQ [Listen] id 104 len 28 Feb 7 02:07:30.327: Se0/2/0:0 LCP: MagicNumber 0x5A0D4435 (0x05065A0D4435) Feb 7 02:07:30.327: Se0/2/0:0 LCP: MRRU 1500 (0x110405DC) Feb 7 02:07:30.327: Se0/2/0:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 7 02:07:30.327: Se0/2/0:0 LCP: O CONFACK [Listen] id 19 len 28 Feb 7 02:07:30.327: Se0/2/0:0 LCP: MagicNumber 0xC57F0DCD (0x0506C57F0DCD) Feb 7 02:07:30.327: Se0/2/0:0 LCP: MRRU 1500 (0x110405DC) Feb 7 02:07:30.327: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 7 02:07:30.331: Se0/2/0:0 LCP: I CONFACK [ACKsent] id 104 len 28 Feb 7 02:07:30.331: Se0/2/0:0 LCP: MagicNumber 0x5A0D4435 (0x05065A0D4435) Feb 7 02:07:30.331: Se0/2/0:0 LCP: MRRU 1500 (0x110405DC) Feb 7 02:07:30.331: Se0/2/0:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 7 02:07:30.331: Se0/2/0:0 LCP: State is Open Feb 7 02:07:30.331: Se0/2/0:0 PPP: Phase is FORWARDING, Attempting Forward Feb 7 02:07:30.335: Se0/2/0:0 LCP: I TERMREQ [Open] id 20 len 4 Feb 7 02:07:30.335: Se0/2/0:0 LCP: Discard packet in FORWARDING phase Feb 7 02:07:30.335: Se0/2/0:0 PPP: Phase is ESTABLISHING, Finish LCP Feb 7 02:07:30.335: Se0/2/0:0 MLP: Request add link to bundle Feb 7 02:07:30.335: Se0/2/0:0 PPP: Phase is VIRTUALIZED Feb 7 02:07:30.335: Se0/2/0:0 MLP: Adding link to bundle Feb 7 02:07:30.339: Mu3 Debug: Condition 1, interface Se0/2/0:0 triggered, count 1 Feb 7 02:07:30.339: Se0/2/0:0 MLP: Computed frag size 5752 exceeds configured value, changed to 1496 Feb 7 02:07:30.339: Mu3 MLP: Added first link Se0/2/0:0 to bundle group147520 Feb 6 20:07:30.343 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to up Feb 7 02:07:30.343: Mu3 PPP: Outbound cdp packet dropped Feb 7 02:07:30.343: Mu3 PPP: Phase is UP Feb 7 02:07:30.343: Mu3 IPCP: O CONFREQ [Closed] id 1 len 10 Feb 7 02:07:30.343: Mu3 IPCP: Address 12.84.188.222 (0x03060C54BCDE) Feb 7 02:07:30.347: Mu3 CDPCP: O CONFREQ [Closed] id 1 len 4 Feb 7 02:07:30.347: Mu3 PPP: Process pending ncp packets Feb 7 02:07:30.347: Se0/2/0:0 PPP: Process pending ncp packets Feb 7 02:07:30.347: Mu3 PPP: Process pending ncp packets Feb 6 20:07:31.343 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink3, changed state to up Feb 7 02:07:32.307: Se0/2/0:0 MLP: cdp packet forwarded to wrong interface Feb 7 02:07:32.331: Se0/2/0:0 LCP: I TERMREQ [Open] id 21 len 4 Feb 7 02:07:32.331: Mu3 MLP: No previous member for idle link in 'group147520' Feb 7 02:07:32.331: Se0/2/0:0 LCP: O TERMACK [Open] id 21 len 4 Feb 7 02:07:32.335: Se0/2/0:0 PPP: Sending Acct Event[Down] id[A2656] Feb 7 02:07:32.335: Se0/2/0:0 MLP: Request drop link from bundle Mu3 Feb 7 02:07:32.335: Se0/2/0:0 PPP: Phase is TERMINATING Feb 7 02:07:32.335: Mu3 MLP: Removing link Se0/2/0:0 from bundle group147520 Feb 7 02:07:32.335: Mu3 MLP: Dropped link Se0/2/0:0 from bundle group147520 Feb 7 02:07:32.335: Mu3 Debug: Condition 1, interface Se0/2/0:0 cleared, count 0 Feb 6 20:07:32.343 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to down Feb 7 02:07:33.307: Se0/2/0:0 PPP: Outbound cdp packet dropped Feb 6 20:07:33.343 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink3, changed state to down
... View more
02-06-2012
05:45 AM
Multilink PPP question I have a Cisco 2811 with 8 serial interfaces. Three of them are in multilink1 which is our active connection to AT&T MPLS. I have the other 5 in multilink3 which will be an upgrade to a new MPLS. The two multilinks have different ip addresses. AT&T cannot get the multilnik3 (the new one) to come up. The serial links are clean with no errors. Cisco TAC looked at the config and ran some debugs. Their conclusion was that the far end AT&T router keeps dropping the multilink. Here is a debug of what it does (this shows only one serial interface in the multilink - for testing purposes). Any thoughts on this would be appreciated. Feb 3 19:58:47.325: Se0/2/0:0 PPP: Phase is ESTABLISHING, Passive Open Feb 3 19:58:47.325: Se0/2/0:0 LCP: State is Listen Feb 3 19:58:47.333: Se0/2/0:0 LCP: I CONFREQ [Listen] id 36 len 28 Feb 3 19:58:47.333: Se0/2/0:0 LCP: MagicNumber 0xB4B32784 (0x0506B4B32784) Feb 3 19:58:47.333: Se0/2/0:0 LCP: MRRU 1500 (0x110405DC) Feb 3 19:58:47.333: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:47.333: Se0/2/0:0 MLP: Peer MRRU (1500) less than group Mu3 MTU (1524) Feb 3 19:58:47.337: Se0/2/0:0 LCP: O CONFREQ [Listen] id 87 len 28 Feb 3 19:58:47.337: Se0/2/0:0 LCP: MagicNumber 0x494755CA (0x0506494755CA) Feb 3 19:58:47.337: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:47.337: Se0/2/0:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:47.337: Se0/2/0:0 LCP: O CONFNAK [Listen] id 36 len 8 Feb 3 19:58:47.337: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:47.341: Se0/2/0:0 LCP: I CONFACK [REQsent] id 87 len 28 Feb 3 19:58:47.341: Se0/2/0:0 LCP: MagicNumber 0x494755CA (0x0506494755CA) Feb 3 19:58:47.341: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:47.341: Se0/2/0:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:47.341: Se0/2/0:0 LCP: I CONFREQ [ACKrcvd] id 37 len 28 Feb 3 19:58:47.341: Se0/2/0:0 LCP: MagicNumber 0xB4B32784 (0x0506B4B32784) Feb 3 19:58:47.341: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:47.341: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:47.341: Se0/2/0:0 LCP: O CONFACK [ACKrcvd] id 37 len 28 Feb 3 19:58:47.341: Se0/2/0:0 LCP: MagicNumber 0xB4B32784 (0x0506B4B32784) Feb 3 19:58:47.341: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:47.345: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:47.345: Se0/2/0:0 LCP: State is Open Feb 3 19:58:47.345: Se0/2/0:0 PPP: Phase is FORWARDING, Attempting Forward Feb 3 19:58:47.349: Se0/2/0:0 LCP: I TERMREQ [Open] id 38 len 4 Feb 3 19:58:47.349: Se0/2/0:0 LCP: Discard packet in FORWARDING phase Feb 3 19:58:47.353: Se0/2/0:0 PPP: Phase is ESTABLISHING, Finish LCP Feb 3 19:58:47.353: Se0/2/0:0 MLP: Request add link to bundle Feb 3 19:58:47.353: Se0/2/0:0 PPP: Phase is VIRTUALIZED Feb 3 19:58:47.353: Se0/2/0:0 MLP: Adding link to bundle Feb 3 19:58:47.353: Mu3 Debug: Condition 1, interface Se0/2/0:0 triggered, count 1 Feb 3 19:58:47.357: Se0/2/0:0 MLP: Computed frag size 5752 exceeds configured value, changed to 1496 Feb 3 19:58:47.357: Mu3 MLP: Added first link Se0/2/0:0 to bundle group147520 Feb 3 19:58:47.357: Se0/3/0:0 MLP: Computed frag size 5752 exceeds MTU, changed to 1496 Feb 3 19:58:47.357: Mu3 MLP: Added link Se0/3/0:0 to bundle group147520 Feb 3 19:58:47.361: Mu3 MLP: Removing link Se0/3/0:0 from bundle group147520 Feb 3 19:58:47.361: Mu3 MLP: Dropped link Se0/3/0:0 from bundle group147520 Feb 3 13:58:47.365 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to up Feb 3 19:58:47.365: Mu3 PPP: Outbound cdp packet dropped Feb 3 19:58:47.369: Mu3 PPP: Phase is UP Feb 3 19:58:47.369: Mu3 IPCP: O CONFREQ [Closed] id 1 len 10 Feb 3 19:58:47.369: Mu3 IPCP: Address 12.84.188.222 (0x03060C54BCDE) Feb 3 19:58:47.369: Mu3 CDPCP: O CONFREQ [Closed] id 1 len 4 Feb 3 19:58:47.369: Mu3 PPP: Process pending ncp packets Feb 3 19:58:47.369: Se0/2/0:0 PPP: Process pending ncp packets Feb 3 19:58:47.369: Mu3 PPP: Process pending ncp packets Feb 3 19:58:48.125: Se0/0/1:0 LCP: Timeout: State Listen Feb 3 19:58:48.129: Se0/0/1:0 LCP: O CONFREQ [Listen] id 148 len 28 Feb 3 19:58:48.129: Se0/0/1:0 LCP: MagicNumber 0x494758E5 (0x0506494758E5) Feb 3 19:58:48.129: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:48.129: Se0/0/1:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:48.137: Se0/0/1:0 LCP: I CONFREQ [REQsent] id 103 len 28 Feb 3 19:58:48.137: Se0/0/1:0 LCP: MagicNumber 0xB4B3202C (0x0506B4B3202C) Feb 3 19:58:48.137: Se0/0/1:0 LCP: MRRU 1500 (0x110405DC) Feb 3 19:58:48.137: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:48.137: Se0/0/1:0 MLP: Peer MRRU (1500) less than group Mu3 MTU (1524) Feb 3 19:58:48.137: Se0/0/1:0 LCP: O CONFNAK [REQsent] id 103 len 8 Feb 3 19:58:48.137: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:48.137: Se0/0/1:0 LCP: I CONFACK [REQsent] id 148 len 28 Feb 3 19:58:48.137: Se0/0/1:0 LCP: MagicNumber 0x494758E5 (0x0506494758E5) Feb 3 19:58:48.137: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:48.137: Se0/0/1:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:48.277: Se0/0/1:0 LCP: I CONFREQ [ACKrcvd] id 104 len 28 Feb 3 19:58:48.277: Se0/0/1:0 LCP: MagicNumber 0xB4B3202C (0x0506B4B3202C) Feb 3 19:58:48.281: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:48.281: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:48.281: Se0/0/1:0 LCP: O CONFACK [ACKrcvd] id 104 len 28 Feb 3 19:58:48.281: Se0/0/1:0 LCP: MagicNumber 0xB4B3202C (0x0506B4B3202C) Feb 3 19:58:48.281: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:48.281: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:48.281: Se0/0/1:0 LCP: State is Open Feb 3 19:58:48.281: Se0/0/1:0 PPP: Phase is FORWARDING, Attempting Forward Feb 3 19:58:48.281: Se0/0/1:0 PPP: Outbound cdp packet dropped Feb 3 19:58:48.313: Se0/0/1:0 PPP: Phase is ESTABLISHING, Finish LCP Feb 3 19:58:48.313: Se0/0/1:0 MLP: Request add link to bundle Feb 3 19:58:48.313: Se0/0/1:0 PPP: Phase is VIRTUALIZED Feb 3 19:58:48.313: Se0/0/1:0 LCP: I TERMREQ [Open] id 105 len 4 Feb 3 19:58:48.313: Se0/0/1:0 LCP: O TERMACK [Open] id 105 len 4 Feb 3 19:58:48.313: Se0/0/1:0 PPP: Sending Acct Event[Down] id[863F8] Feb 3 19:58:48.313: Se0/0/1:0 PPP: Phase is TERMINATING Feb 3 19:58:48.313: Se0/0/1:0 MLP: Can't add link to bundle, interface renegotiated without MP Feb 3 19:58:48.317: Se0/2/1:0 MLP: Computed frag size 5752 exceeds MTU, changed to 1496 Feb 3 19:58:48.317: Mu3 MLP: Added link Se0/2/1:0 to bundle group147520 Feb 3 13:58:48.365 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Multilink3, changed state to up Feb 3 19:58:49.513: Se0/0/1:0 PPP: Outbound cdp packet dropped Feb 3 19:58:49.513: Se0/2/0:0 LCP: I TERMREQ [Open] id 39 len 4 Feb 3 19:58:49.513: Se0/2/0:0 LCP: O TERMACK [Open] id 39 len 4 Feb 3 19:58:49.513: Se0/2/0:0 PPP: Sending Acct Event[Down] id[863F5] Feb 3 19:58:49.513: Se0/2/0:0 MLP: Request drop link from bundle Mu3 Feb 3 19:58:49.517: Se0/2/0:0 PPP: Phase is TERMINATING Feb 3 19:58:49.517: Mu3 MLP: Removing link Se0/2/0:0 from bundle group147520 Feb 3 19:58:49.517: Mu3 MLP: Dropped link Se0/2/0:0 from bundle group147520 Feb 3 19:58:49.517: Mu3 Debug: Condition 1, interface Se0/2/0:0 cleared, count 0 Feb 3 13:58:49.533 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/1:0, changed state to up Feb 3 19:58:50.589: Se0/0/1:0 LCP: Timeout: State TERMsent Feb 3 19:58:50.589: Se0/0/1:0 LCP: State is Closed Feb 3 19:58:50.589: Se0/0/1:0 PPP: Phase is DOWN Feb 3 19:58:50.593: Se0/0/1:0 PPP: Phase is ESTABLISHING, Passive Open Feb 3 19:58:50.593: Se0/0/1:0 LCP: State is Listen Feb 3 13:58:50.605 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to down Feb 3 19:58:51.505: Se0/2/0:0 LCP: Timeout: State TERMsent Feb 3 19:58:51.505: Se0/2/0:0 LCP: State is Closed Feb 3 19:58:51.505: Se0/2/0:0 PPP: Phase is DOWN Feb 3 19:58:51.505: Se0/2/0:0 PPP: Phase is ESTABLISHING, Passive Open Feb 3 19:58:51.505: Se0/2/0:0 LCP: State is Listen Feb 3 19:58:52.177: Se0/2/0:0 LCP: I CONFREQ [Listen] id 40 len 28 Feb 3 19:58:52.177: Se0/2/0:0 LCP: MagicNumber 0xB4B337F0 (0x0506B4B337F0) Feb 3 19:58:52.177: Se0/2/0:0 LCP: MRRU 1500 (0x110405DC) Feb 3 19:58:52.177: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:52.177: Se0/2/0:0 MLP: Peer MRRU (1500) less than group Mu3 MTU (1524) Feb 3 19:58:52.177: Se0/2/0:0 LCP: O CONFREQ [Listen] id 88 len 28 Feb 3 19:58:52.177: Se0/2/0:0 LCP: MagicNumber 0x494768BD (0x0506494768BD) Feb 3 19:58:52.177: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:52.177: Se0/2/0:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:52.177: Se0/2/0:0 LCP: O CONFNAK [Listen] id 40 len 8 Feb 3 19:58:52.177: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 13:58:52.181 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to up Feb 3 13:58:52.185 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/1:0, changed state to down Feb 3 19:58:52.201: Se0/2/0:0 LCP: I CONFACK [REQsent] id 88 len 28 Feb 3 19:58:52.201: Se0/2/0:0 LCP: MagicNumber 0x494768BD (0x0506494768BD) Feb 3 19:58:52.201: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:52.201: Se0/2/0:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:52.201: Se0/2/0:0 LCP: I CONFREQ [ACKrcvd] id 41 len 28 Feb 3 19:58:52.201: Se0/2/0:0 LCP: MagicNumber 0xB4B337F0 (0x0506B4B337F0) Feb 3 19:58:52.201: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:52.205: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:52.205: Se0/2/0:0 LCP: O CONFACK [ACKrcvd] id 41 len 28 Feb 3 19:58:52.205: Se0/2/0:0 LCP: MagicNumber 0xB4B337F0 (0x0506B4B337F0) Feb 3 19:58:52.205: Se0/2/0:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:52.205: Se0/2/0:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:52.205: Se0/2/0:0 LCP: State is Open Feb 3 19:58:52.205: Se0/2/0:0 PPP: Phase is FORWARDING, Attempting Forward Feb 3 19:58:52.213: Se0/2/0:0 LCP: I TERMREQ [Open] id 42 len 4 Feb 3 19:58:52.213: Se0/2/0:0 LCP: Discard packet in FORWARDING phase Feb 3 19:58:52.213: Se0/2/0:0 PPP: Phase is ESTABLISHING, Finish LCP Feb 3 19:58:52.213: Se0/2/0:0 MLP: Request add link to bundle Feb 3 19:58:52.213: Se0/2/0:0 PPP: Phase is VIRTUALIZED Feb 3 19:58:52.213: Se0/2/0:0 MLP: Adding link to bundle Feb 3 19:58:52.213: Mu3 Debug: Condition 1, interface Se0/2/0:0 triggered, count 1 Feb 3 19:58:52.217: Se0/2/0:0 MLP: Computed frag size 5752 exceeds configured value, changed to 1496 Feb 3 19:58:52.217: Mu3 MLP: Added first link Se0/2/0:0 to bundle group147520 Feb 3 13:58:52.217 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to up Feb 3 19:58:52.217: Mu3 PPP: Phase is UP Feb 3 19:58:52.221: Mu3 IPCP: O CONFREQ [Closed] id 1 len 10 Feb 3 19:58:52.221: Mu3 IPCP: Address 12.84.188.222 (0x03060C54BCDE) Feb 3 19:58:52.221: Mu3 CDPCP: O CONFREQ [Closed] id 1 len 4 Feb 3 19:58:52.221: Mu3 PPP: Process pending ncp packets Feb 3 19:58:52.221: Se0/2/0:0 PPP: Process pending ncp packets Feb 3 19:58:52.221: Mu3 PPP: Process pending ncp packets Feb 3 19:58:53.713: Se0/0/1:0 LCP: Timeout: State Listen Feb 3 19:58:53.717: Se0/0/1:0 LCP: O CONFREQ [Listen] id 149 len 28 Feb 3 19:58:53.717: Se0/0/1:0 LCP: MagicNumber 0x49476EBE (0x050649476EBE) Feb 3 19:58:53.717: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:53.717: Se0/0/1:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:53.717: Se0/2/0:0 MLP: cdp packet forwarded to wrong interface Feb 3 19:58:53.745: Mu3 PPP: Outbound cdp packet dropped Feb 3 19:58:53.749: Se0/0/1:0 LCP: I CONFREQ [REQsent] id 107 len 28 Feb 3 19:58:53.749: Se0/0/1:0 LCP: MagicNumber 0xB4B33337 (0x0506B4B33337) Feb 3 19:58:53.749: Se0/0/1:0 LCP: MRRU 1500 (0x110405DC) Feb 3 19:58:53.749: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:53.749: Se0/0/1:0 MLP: Peer MRRU (1500) less than group Mu3 MTU (1524) Feb 3 19:58:53.749: Se0/0/1:0 LCP: O CONFNAK [REQsent] id 107 len 8 Feb 3 19:58:53.749: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:53.753: Se0/0/1:0 LCP: I CONFACK [REQsent] id 149 len 28 Feb 3 19:58:53.753: Se0/0/1:0 LCP: MagicNumber 0x49476EBE (0x050649476EBE) Feb 3 19:58:53.753: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:53.757: Se0/0/1:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:53.757: Se0/0/1:0 LCP: I CONFREQ [ACKrcvd] id 108 len 28 Feb 3 19:58:53.757: Se0/0/1:0 LCP: MagicNumber 0xB4B33337 (0x0506B4B33337) Feb 3 19:58:53.757: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:53.757: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:53.757: Se0/0/1:0 LCP: O CONFACK [ACKrcvd] id 108 len 28 Feb 3 19:58:53.757: Se0/0/1:0 LCP: MagicNumber 0xB4B33337 (0x0506B4B33337) Feb 3 19:58:53.757: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:53.757: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:53.757: Se0/0/1:0 LCP: State is Open Feb 3 19:58:53.757: Se0/0/1:0 PPP: Phase is FORWARDING, Attempting Forward Feb 3 19:58:53.761: Se0/0/1:0 PPP: Phase is ESTABLISHING, Finish LCP Feb 3 19:58:53.761: Se0/0/1:0 MLP: Request add link to bundle Feb 3 19:58:53.761: Se0/0/1:0 PPP: Phase is VIRTUALIZED Feb 3 19:58:53.761: Se0/0/1:0 MLP: Adding link to bundle Feb 3 19:58:53.761: Mu3 Debug: Condition 2, interface Se0/0/1:0 triggered, count 2 Feb 3 19:58:53.761: Se0/0/1:0 MLP: Computed frag size 5752 exceeds MTU, changed to 1496 Feb 3 19:58:53.765: Mu3 MLP: Added link Se0/0/1:0 to bundle group147520 Feb 3 19:58:53.765: Se0/0/1:0 LCP: I TERMREQ [Open] id 109 len 4 Feb 3 19:58:53.765: Se0/0/1:0 LCP: O TERMACK [Open] id 109 len 4 Feb 3 19:58:53.765: Se0/0/1:0 PPP: Sending Acct Event[Down] id[863FF] Feb 3 19:58:53.765: Se0/0/1:0 MLP: Request drop link from bundle Mu3 Feb 3 19:58:53.765: Se0/0/1:0 PPP: Phase is TERMINATING Feb 3 19:58:53.765: Mu3 MLP: Removing link Se0/0/1:0 from bundle group147520 Feb 3 19:58:53.765: Mu3 MLP: Dropped link Se0/0/1:0 from bundle group147520 Feb 3 19:58:53.765: Mu3 Debug: Condition 2, interface Se0/0/1:0 cleared, count 1 Feb 3 19:58:54.921: Mu3 IPCP: Timeout: State REQsent Feb 3 19:58:54.921: Mu3 IPCP: O CONFREQ [REQsent] id 2 len 10 Feb 3 19:58:54.921: Mu3 IPCP: Address 12.84.188.222 (0x03060C54BCDE) Feb 3 13:58:54.925 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0:0, changed state to up Feb 3 19:58:54.945: Mu3 PPP: Outbound cdp packet dropped Feb 3 19:58:54.945: Mu3 CDPCP: Timeout: State REQsent Feb 3 19:58:54.945: Mu3 CDPCP: O CONFREQ [REQsent] id 2 len 4 Feb 3 19:58:54.949: Se0/2/0:0 LCP: I TERMREQ [Open] id 43 len 4 Feb 3 19:58:54.949: Mu3 MLP: No previous member for idle link in 'group147520' Feb 3 19:58:54.949: Se0/2/0:0 LCP: O TERMACK [Open] id 43 len 4 Feb 3 19:58:54.949: Se0/2/0:0 PPP: Sending Acct Event[Down] id[863FD] Feb 3 19:58:54.949: Se0/2/0:0 MLP: Request drop link from bundle Mu3 Feb 3 19:58:54.949: Se0/2/0:0 PPP: Phase is TERMINATING Feb 3 19:58:54.953: Mu3 MLP: Removing link Se0/2/0:0 from bundle group147520 Feb 3 19:58:54.953: Mu3 MLP: Dropped link Se0/2/0:0 from bundle group147520 Feb 3 19:58:54.953: Mu3 Debug: Condition 1, interface Se0/2/0:0 cleared, count 0 Feb 3 13:58:54.961 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to down Feb 3 13:58:54.973 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to up Feb 3 19:58:56.081: Se0/0/1:0 LCP: I CONFREQ [TERMsent] id 110 len 28 Feb 3 19:58:56.081: Se0/0/1:0 LCP: MagicNumber 0xB4B34899 (0x0506B4B34899) Feb 3 19:58:56.081: Se0/0/1:0 LCP: MRRU 1500 (0x110405DC) Feb 3 19:58:56.081: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:56.081: Se0/0/1:0 LCP: Dropping packet, state is TERMsent Feb 3 13:58:56.093 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/2/0:0, changed state to down Feb 3 19:58:56.093: Se0/2/0:0 PPP: Outbound cdp packet dropped Feb 3 19:58:56.101: Se0/0/1:0 LCP: Timeout: State TERMsent Feb 3 19:58:56.101: Se0/0/1:0 LCP: State is Closed Feb 3 19:58:56.101: Se0/0/1:0 PPP: Phase is DOWN Feb 3 19:58:56.101: Se0/0/1:0 PPP: Phase is ESTABLISHING, Passive Open Feb 3 19:58:56.101: Se0/0/1:0 LCP: State is Listen Feb 3 19:58:57.837: Se0/2/0:0 LCP: Timeout: State TERMsent Feb 3 19:58:57.837: Se0/2/0:0 LCP: State is Closed Feb 3 19:58:57.837: Se0/2/0:0 PPP: Phase is DOWN Feb 3 19:58:57.841: Se0/2/0:0 PPP: Phase is ESTABLISHING, Passive Open Feb 3 19:58:57.841: Se0/2/0:0 LCP: State is Listen Feb 3 13:58:57.845 CST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/3/1:0, changed state to up Feb 3 19:58:57.857: Se0/0/1:0 LCP: I CONFREQ [Listen] id 111 len 28 Feb 3 19:58:57.857: Se0/0/1:0 LCP: MagicNumber 0xB4B34899 (0x0506B4B34899) Feb 3 19:58:57.857: Se0/0/1:0 LCP: MRRU 1500 (0x110405DC) Feb 3 19:58:57.857: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:57.861: Se0/0/1:0 MLP: Peer MRRU (1500) less than group Mu3 MTU (1524) Feb 3 19:58:57.861: Se0/0/1:0 LCP: O CONFREQ [Listen] id 150 len 28 Feb 3 19:58:57.861: Se0/0/1:0 LCP: MagicNumber 0x49477EF2 (0x050649477EF2) Feb 3 19:58:57.861: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:57.861: Se0/0/1:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:57.861: Se0/0/1:0 LCP: O CONFNAK [Listen] id 111 len 8 Feb 3 19:58:57.861: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:57.869: Se0/0/1:0 LCP: I CONFACK [REQsent] id 150 len 28 Feb 3 19:58:57.869: Se0/0/1:0 LCP: MagicNumber 0x49477EF2 (0x050649477EF2) Feb 3 19:58:57.869: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:57.869: Se0/0/1:0 LCP: EndpointDisc 1 Ply2811MPLS (0x130E01506C79323831314D504C53) Feb 3 19:58:57.869: Se0/0/1:0 LCP: I CONFREQ [ACKrcvd] id 112 len 28 Feb 3 19:58:57.869: Se0/0/1:0 LCP: MagicNumber 0xB4B34899 (0x0506B4B34899) Feb 3 19:58:57.869: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:57.869: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:57.873: Se0/0/1:0 LCP: O CONFACK [ACKrcvd] id 112 len 28 Feb 3 19:58:57.873: Se0/0/1:0 LCP: MagicNumber 0xB4B34899 (0x0506B4B34899) Feb 3 19:58:57.873: Se0/0/1:0 LCP: MRRU 1524 (0x110405F4) Feb 3 19:58:57.873: Se0/0/1:0 LCP: EndpointDisc 1 group147520 (0x130E0167726F7570313437353230) Feb 3 19:58:57.873: Se0/0/1:0 LCP: State is Open Feb 3 19:58:57.873: Se0/0/1:0 PPP: Phase is FORWARDING, Attempting Forward Feb 3 13:58:57.873 CST: %LINK-3-UPDOWN: Interface Multilink3, changed state to down Feb 3 19:58:57.877: Se0/0/1:0 PPP: Phase is ESTABLISHING, Finish LCP Feb 3 19:58:57.877: Se0/0/1:0 MLP: Request add link to bundle Feb 3 19:58:57.877: Se0/0/1:0 PPP: Phase is VIRTUALIZED Feb 3 19:58:57.877: Se0/0/1:0 LCP: I TERMREQ [Open] id 113 len 4 Feb 3 19:58:57.877: Se0/0/1:0 LCP: O TERMACK [Open] id 113 len 4 Feb 3 19:58:57.877: Se0/0/1:0 PPP: Sending Acct Event[Down] id[86404] Feb 3 19:58:57.877: Se0/0/1:0 PPP: Phase is TERMINATING Feb 3 19:58:57.877: Se0/0/1:0 MLP: Can't add link to bundle, interface renegotiated without MP *********************************************************************************** *** *** *** *** Unauthorized Access Strictly Prohibited *** *** *** *** *** ******************************************************************************** User Access Verification Username: bfairchild Password: Ply2811MPLS# Ply2811MPLS# Ply2811MPLS#sh run Building configuration... Current configuration : 5954 bytes ! ! Last configuration change at 12:25:53 CST Fri Feb 3 2012 by bfairchild ! NVRAM config last updated at 12:27:20 CST Fri Feb 3 2012 by bfairchild ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec localtime show-timezone no service password-encryption ! hostname Ply2811MPLS ! boot-start-marker boot system flash:c2800nm-entbasek9-mz.124-20.T4.bin boot-end-marker ! card type t1 0 2 card type t1 0 3 logging message-counter syslog logging buffered 20000 ! aaa new-model ! ! aaa authentication login default group tacacs+ local aaa authorization console aaa authorization exec default group tacacs+ local if-authenticated aaa authorization commands 0 default group tacacs+ local aaa authorization commands 1 default group tacacs+ local aaa authorization commands 15 default group tacacs+ local aaa accounting exec default start-stop group tacacs+ aaa accounting commands 0 default start-stop group tacacs+ aaa accounting commands 1 default start-stop group tacacs+ aaa accounting commands 15 default start-stop group tacacs+ aaa accounting network acct_methods start-stop group rad_acct aaa accounting system default start-stop group tacacs+ ! ! aaa session-id common clock timezone CST -6 clock summer-time CDT recurring no network-clock-participate wic 0 no network-clock-participate wic 1 no network-clock-participate wic 2 no network-clock-participate wic 3 ! dot11 syslog ip source-route ! ! ip cef ! ! multilink bundle-name authenticated ! ! ! ! ! ! username local privilege 15 secret 5 $1$WEe9$jSgGX8j8ggTp8Xs57qPxr. archive log config hidekeys ! ! controller T1 0/0/0 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! controller T1 0/0/1 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! controller T1 0/1/0 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! controller T1 0/1/1 framing esf linecode b8zs channel-group 0 timeslots 1-24 ! controller T1 0/2/0 framing esf linecode b8zs cablelength long 0db channel-group 0 timeslots 1-24 ! controller T1 0/2/1 framing esf linecode b8zs cablelength long 0db channel-group 0 timeslots 1-24 ! controller T1 0/3/0 framing esf linecode b8zs cablelength long 0db channel-group 0 timeslots 1-24 ! controller T1 0/3/1 framing esf linecode b8zs cablelength long 0db channel-group 0 timeslots 1-24 ! ! class-map match-all VOICE-CONTROL match access-group 151 class-map match-all VOICE match access-group 150 ! ! policy-map WAN-EDGE class VOICE priority percent 50 class VOICE-CONTROL priority percent 1 class class-default fair-queue ! ! ! ! interface Tunnel64 no ip address shutdown ! interface Multilink1 ip address 12.85.128.34 255.255.255.252 ip flow ingress ip flow egress ppp multilink ppp multilink group 1 service-policy output WAN-EDGE ! interface Multilink2 no ip address ip flow ingress ip flow egress shutdown ppp multilink ppp multilink group 2 service-policy output WAN-EDGE ! interface Multilink3 mtu 1524 ip address 12.84.188.222 255.255.255.252 ppp multilink ppp multilink group 3 ! interface FastEthernet0/0 ip address 192.168.64.2 255.255.255.248 ip accounting output-packets duplex auto speed auto ! interface FastEthernet0/1 ip address 192.168.64.18 255.255.255.252 delay 500000 duplex auto speed auto ! interface Serial0/0/0:0 no ip address encapsulation ppp ppp multilink ppp multilink group 1 ! interface Serial0/0/1:0 no ip address encapsulation ppp ppp multilink ppp multilink group 3 ! interface Serial0/1/0:0 no ip address encapsulation ppp ppp multilink ppp multilink group 1 ! interface Serial0/1/1:0 no ip address encapsulation ppp ppp multilink ppp multilink group 1 ! interface Serial0/2/0:0 no ip address encapsulation ppp ppp multilink ppp multilink group 3 ppp multilink fragment size 1496 ! interface Serial0/2/1:0 no ip address encapsulation ppp ppp multilink ppp multilink group 3 ! interface Serial0/3/0:0 no ip address encapsulation ppp ppp multilink ppp multilink group 3 ! interface Serial0/3/1:0 no ip address encapsulation ppp ppp multilink ppp multilink group 3 ! router eigrp 100 redistribute bgp 65001 metric 1500 1 255 1 1500 network 10.0.64.0 0.0.7.255 network 192.168.64.0 0.0.0.7 network 192.168.64.16 0.0.0.3 no auto-summary ! router bgp 65001 no synchronization bgp log-neighbor-changes network 10.0.64.0 mask 255.255.248.0 network 10.164.64.0 mask 255.255.248.0 network 12.20.38.32 mask 255.255.255.240 network 172.16.10.0 mask 255.255.255.0 network 192.168.64.0 mask 255.255.255.248 network 192.168.64.8 mask 255.255.255.252 network 192.168.64.12 mask 255.255.255.252 network 192.168.64.16 mask 255.255.255.252 network 192.168.64.24 mask 255.255.255.248 neighbor 12.85.128.33 remote-as 7018 no auto-summary ! ip forward-protocol nd ! no ip http server no ip http secure-server ip flow-export source Multilink1 ip flow-export version 5 ip flow-export destination 10.0.105.17 2055 ! ip tacacs source-interface FastEthernet0/0 ! logging trap notifications logging source-interface FastEthernet0/0 logging 10.0.104.52 access-list 101 deny ip any host 10.164.0.11 access-list 101 deny ip any host 10.164.0.12 access-list 101 deny ip any host 10.164.0.13 access-list 101 permit ip any any access-list 150 permit ip any any dscp ef access-list 151 permit ip any any dscp cs5 snmp-server community wg96gbltd RO snmp-server community wg96GBLTD RW ! ! tacacs-server host 10.0.104.231 tacacs-server host 10.0.87.140 tacacs-server directed-request tacacs-server key 7 044C5B0F582D1E425A ! control-plane ! banner motd ^C*********************************************************************************** *** *** *** *** Unauthorized Access Strictly Prohibited *** *** *** *** *** ******************************************************************************** ^C ! line con 0 line aux 0 line vty 0 4 ! scheduler allocate 20000 1000 ntp server 10.0.96.93 end
... View more
Labels:
11-23-2011
04:18 AM
Thanks for the feedback - we have not upgraded to cucm 8 yet so this is helpful. What version of cucm did you test with? Thanks, Bill
... View more
05-25-2011
02:07 PM
Has anyone tried the Fidelus Console (operator attendant console)? When I upgrade to CUCM 8.x I'm going to need an attendant console. I think the ARC one that Cisco is pushing which requires a seperate server is overkill for what we need. I would also be interested in hearing from anyone who uses any of the Fidelus products to learn about their support capabilities. Thanks, Bill
... View more
Labels:
Created by
gb-fairchild
in IP Telephony and Phones
in IP Telephony and Phones
04-14-2011
06:21 AM
04-14-2011
06:21 AM
Thanks - Can't do it from the router because the D-channel is backhauled to Call Manager? But Call Manager knows - it will create a CDR record for it so you would think it could be done from there some how.
... View more
Created by
gb-fairchild
in IP Telephony and Phones
in IP Telephony and Phones
04-13-2011
04:56 PM
04-13-2011
04:56 PM
I'm looking at my gateway and can see from using the show voice port stat command that one channel on the PRI (MGCP) is in use. Is there a way to tell who (which DN) is using it? I want to shut down the gateway to change a PVDMII but don't just want to dump whoever is using it. Thanks, Bill
... View more
Labels:
Created by
gb-fairchild
in IP Telephony and Phones
in IP Telephony and Phones
04-01-2011
10:36 AM
04-01-2011
10:36 AM
Any update on being able to use CUPC without presence server?
... View more
02-01-2011
06:58 AM
I agree - I was just thinking that this has been running for 5 years using the Windows NTP without any problems. It seems to be happy again after the restart. I will check into that registry setting. Thanks for your help. Bill
... View more
01-31-2011
06:05 PM
This works with Meeting Place - once I realized that the call from Meeting Place i s inbound as far as the SIP trunk is concerned. Thanks for your Help.
... View more
01-31-2011
05:55 PM
I'm getting this from RTMT: At Mon Jan 31 20:30:25 EST 2011 on node 10.164.0.11, the following SyslogSeverityMatchFound events generated: SeverityMatch - Critical ntpRunningStatus.sh: The local NTP client is off by more than the acceptable threshold of 3 seconds from its remote NTP system peer. The normal remedy is for NTP Watch Dog to automatically restart NTP. However, an unusual number of automatic NTP restarts have already occurred on this node. No additional automatic NTP restarts will be done until NTP time synchronization stabilizes. Check NTP status via CLI 'utils ntp status' and ensure good network connectivity to the remote NTP server(s). After rectifying the problem, restart NTP on this node and any dependent nodes via CLI 'utils ntp restart'. If all else fails, schedule a reboot of this server. When I check status from CLI on publisher (CUCM 7.1.3) I get: admin:utils ntp status ntpd (pid 20391) is running... remote refid st t when poll reach delay offset jitter ============================================================================== *127.127.1.0 LOCAL(0) 10 l 5 64 377 0.000 0.000 0.004 x10.0.17.3 10.0.17.4 3 u 127 1024 377 0.572 -119932 229.778 x10.0.96.93 .GPS. 1 u 185 1024 377 7.986 -1.865 1.466 synchronised to local net at stratum 11 time correct to within 11 ms polling server every 1024 s Current time in UTC is : Tue Feb 1 01:34:46 UTC 2011 Current time in America/New_York is : Mon Jan 31 20:34:46 EST 2011 Not sure what this is telling me - but it says time is correct to within 11ms Thanks, Bill
... View more
Labels:
01-26-2011
07:50 PM
I created 2 partitions, one with the internal numbers, one with the route patterns for external calls. I gave the external route partition the highest priority in the CSS. Works on my test using a phone. To test with Meeting Place I have to wait for the weekend.
... View more
01-11-2013
Did you ever figure this out?? I have one remote site that reports
periodic drops. TAC has not been ...
Created by
gb-fairchild
in Collaboration Applications
11-12-2012
11-12-2012
I did as you suggested - quit Jabber, opened a one-click from Outlook
and then tried to start Jabber...
Created by
gb-fairchild
in Collaboration Applications
11-11-2012
11-11-2012
Jabber 9.1CUCM 7.1.3Windows 7 32 bitCisco Presence 8.0.2.10000-30 Jabber
for windows - periodically ...
Created by
gb-fairchild
in IP Telephony and Phones
10-05-2012
10-05-2012
We are replacing a Mitel PBX at one of our sites with call manager and a
2951 router as an MGCP gate...
06-28-2012
We have call Manager 7.1.3, MGCP gateway on Cisco 2811 running IOS
Version 12.4(25b), with SRST conf...
02-09-2012
Here is the solution(from Cisco TAC): There are two mutlilink's on this
router. Both were using the ...
02-06-2012
Thanks for looking at this. I changed the mtu size as you suggested.
Still no luck. It looks ok unti...
02-06-2012
Multilink PPP questionI have a Cisco 2811 with 8 serial interfaces.
Three of them are in multilink1 ...
11-23-2011
Thanks for the feedback - we have not upgraded to cucm 8 yet so this is
helpful. What version of cuc...
05-25-2011
Has anyone tried the Fidelus Console (operator attendant console)? When
I upgrade to CUCM 8.x I'm go...
Created by
gb-fairchild
in IP Telephony and Phones
04-14-2011
04-14-2011
Thanks - Can't do it from the router because the D-channel is backhauled
to Call Manager? But Call M...
Created by
gb-fairchild
in IP Telephony and Phones
04-13-2011
04-13-2011
I'm looking atmy gateway and can see from using the show voice port stat
command that one channel on...
Created by
gb-fairchild
in IP Telephony and Phones
04-01-2011
04-01-2011
Any update on being able to use CUPC without presence server?
Public Statistics
| Date Registered | 04-18-2008 12:42 PM |
| Date Last Visited | 08-18-2017 03:56 AM |
| Total Messages Posted | 74 |
| Total Helpful Votes Received | 10 |
.jpg "Hall of Fame Cisco Employee"){kind=icon}
