About Justin DeVaughn

Justin DeVaughn · 03-05-2013

I've attached a visio diagram of the configuration for reference.I'm having two problems:1. I cannot ping the VIP 10.10.1.1 on the MS NLB servers from other subnets on their ODD numbered IPs. For instance 192.168.1.1 cannot ping the VIP while 192.1...

Justin DeVaughn · 03-05-2013

I've attached a visio diagram of the configuration for reference.I'm having two problems:1. I cannot ping the VIP 10.10.1.1 on the MS NLB servers from other subnets on their ODD numbered IPs. For instance 192.168.1.1 cannot ping the VIP while 192.1...

Justin DeVaughn · 02-08-2012

The network is set up like this.Host -----> 3750 (classic) running IPSERVICES stack ----> 3550 router -----> VPN 3005 Concentrator.IP routing is disabled on the 3750 (it's acting solely as a switch)IP routing is enabled with an EIGRP process running ...

Justin DeVaughn · 11-21-2011

Hi,The DHCP/DNS server is on ip address 10.1.100.103 with an alt on .102I'm attempting to integrate a 4510R+E into an existing network and use existing DHCP/DNS windows 2008 server to push out IP addresses to connected computers.I want to assign a VL...

Justin DeVaughn · 11-08-2011

Hi all,I received a 4510R+E preconfigured with Enterprise services on it. I plugged into the console of the active sup7-E after initializing the chassis and it doesn't let me put an ip address on any interface. When I use ? command syntax help it d...

Justin DeVaughn · 10-18-2014

Travis, Outstanding news! Did you upgrade the FUS code to the correlating version as well? It's important to remember FUS (firmware) can be specific to both the controller hardware model (i.e. 5500, 5750, 2500 etc...) and the version of code you ...

Justin DeVaughn · 10-15-2014

Sorry Travis, Try this CLI command "capwap ap controller ip address (ip address) (subnet mask)"I recalled the command incorrectly. I do apologize! Also, you might want to make sure you have connectivity to the management interface of the WLC as well...

Justin DeVaughn · 10-14-2014

If you had the following it would work:Switch:VLAN 1 - insideVLAN 2 - dmzswitchport 1 (inside) - access mode vlan 1switchport 2 (dmz) - access mode vlan 2 Firewall:port 1 (inside) - (ip address + plugged into switchport 1)port 2 (dmz) - (ip address +...

Justin DeVaughn · 10-14-2014

Hi Travis, The required WLC software for 2602 APs to successfully join is 7.3+ so you may want to make sure the WLC you're trying to connect to is at least that high on it's code version. Otherwise, console into the ap and issue the command "capwap ...

Justin DeVaughn · 10-14-2014

Hi Asad,Can you upload the output from "show ip route"Also include the output from "ping 172.18.2.12 source 10.50.105.254"Regards,Justin

Member Since	‎08-09-2011 03:26 PM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	36
Total Helpful Votes Received	10

User Statistics

User Activity

Problems with MS NLB over vPC using N5K and 6509E

Problems with MS NLB over vPC using N5K and 6509E

Layer 3 connectivity issues.

Problem assigning IP address through DHCP on new 4500E install.

Orange status lights on out-of-the-box 4510R+E sup7-E...Help!

Travis,

Sorry Travis, Try this CLI

If you had the following it

Hi Travis, The required WLC

Hi Asad,Can you upload the