About pjwhitby_2

pjwhitby_2 · 02-22-2012

Hi all,I have a 3845 with 4 x 2-port E1 VWICs, each port contains an ISDN30 circuit, therefore I have 240 voice channels connected.How can I monitor the total number of voice channels currently in use, preferably via SNMP monitoring of the 3845? We a...

pjwhitby_2 · 01-18-2012

okay, I need help, I am sure my config is correct but I am getting no joyI have four sites, siteA, siteB, siteC and SiteD. Now siteC and SiteD both connect to siteB via an IPSec VPN. There is no requirement for connectivity between siteC and siteD. C...

pjwhitby_2 · 10-19-2011

heres my scenario, we are running BM installs of Windows 2008 R2 x64 SP1 on B200 M2 blades (with M71KR-E CNAs). Now, the installs are streamed PVS images and are run exclusively in RAM. We ran into some difficulties with event logs, crash dumps etc s...

pjwhitby_2 · 10-19-2011

Hi All,I am getting conflicting answers on supportability. We are running the following hardwareB200-M2 blades with M71KR-E CNAs running firmware package 1.4(3i)and according to the recently released UCS Hardware and Software Interoperability Utility...

pjwhitby_2 · 08-03-2011

Am I able to restrict users to the KVM console only within UCSM?What Roles do I need to assign to the user to ensure all they can do is access the KVM Console? It is not a huge issue if they obtain read-only rights tot he UCSM itself.

pjwhitby_2 · 04-17-2012

hey Wallace,sorry, we never got this running and we worked in a work around, although I cannot remember what it was, I think we went with a round robin DNS solution, but I would have to check.Paul

pjwhitby_2 · 02-26-2012

we are runningc3845-ipvoicek9-mz.124-24.T4.binIts just that whenever I check the SNMP figure is always not a correct indication of the number of active calls, we are also running a full UCCE environment, but I cant see how that would impact the numbe...

pjwhitby_2 · 02-22-2012

that seems to give inbound call volume only, is that to be expected?for example, and I need to do this quicklycvCallActiveDS0s gives me a count of 186show voice call status | i active gives me a count of 191show isdn active | i Out gives me a count o...

pjwhitby_2 · 01-23-2012

the routing was fine, I found the issuesame-security-traffic permit intra-interfaceOnce I entered this traffic started flowing.Problem solved but thanks for helping Andrew.

pjwhitby_2 · 01-22-2012

okay, I have added the following lines to address point 2access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.255.255.0 192.168.32.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.255.255.0 192.168.33.0 255...

Member Since	‎11-18-2009 08:35 AM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	24

User Statistics

User Activity

How do I monitor the number of voice calls on my voice gateways?

site-to-site-to-site IPSec VPN config

BM installs Win2k8, Citrix PVS and SAN storage

MS Win 2k8 and B200-M2 Blade Support

KVM only access via UCSM

How do I load balance TFTP between two servers and a client on t

How do I monitor the number of voice calls on my voice gateways?

How do I monitor the number of voice calls on my voice gateways?

Re: site-to-site-to-site IPSec VPN config

site-to-site-to-site IPSec VPN config