hi guys, Thx for your answer... As i was googling my question, i found also that E1 would use 1,2 & 7,8... is that correct too? Thx again! ... View more

Well, I'm close to a full comprehension So my controllers DSL are configured in CPE Mode (line term CPE I guess?). Sometimes, DSL controllers are configured in auto, that means the rate is negotiated with the CO, and I can gues the rate by the addition of all the line rate (line-0, line-1 etc.), right? Other times, DSL controllers are configured with a static rate, that means the rate is NOT negotiated with the CO, and I can gues the real rate of the line by the lowest value beetween DSL configured line rate and line rate addition (that is the CPO <-> CPE speed)? 1.CO set for 2048 and CPE set for auto  --> line-0+line-1+... = rate will be 2048 2. CO set for 2048 and CPE set for 1024 --> sum(line-n) = line rate will be 1024 3. CO set for 1024 and CPE set for 2048 --> sum(line-n) = line rate will be 1024 4. CO set for 2048 and CPE set for 2048 --> sum(line-n) = line rate will be 2048 Thanks a lot again and again ... View more

I have not the hand on the CPE, so I can not modify config, sorry... I thought i understood your explain, but i think that i missed an information. what is the CO? Is it the DSLAM? or the line-0, line-1 etc.? ex: (explain                    ==> sh run traduction) CPE set for 2048     ==> "Configured Line rate: 2048Kbps" CO set for 1024       ==> "Line-0 status[...]Line rate:  512 Kbps"                                      "Line-1 status[...]Line rate: 512 Kbps" Thanks again, Greg ... View more

(ok, i thought that if i have a 4-wire, i should find line 0, 1, 2 & 3. But actually 4-wire == line 0,1  and 2-wire == line 0 only... that's it?) First CPE: sh controllers dsl DSL 0 controller UP SLOT 0: Globespan xDSL controller chipset Frame mode: Utopia Configured Line rate: 4608Kbps Line Mode: Four Wire Enhanced Mode DSL mode: SHDSL Annex B Line Re-activated 327 times after system bootup LOSW Defect alarm: ACTIVE CRC per second alarm: ACTIVE Line termination: CPE Line 0 statistics         Current 15 min CRC: 0         Current 15 min LOSW Defect: 0         Current 15 min ES: 0         Current 15 min SES: 0         Current 15 min UAS: 0         Previous 15 min CRC: 0         Previous 15 min LOSW Defect: 0         Previous 15 min ES: 0         Previous 15 min SES: 0         Previous 15 min UAS: 0 Line 1 statistics         Current 15 min CRC: 0         Current 15 min LOSW Defect: 0         Current 15 min ES: 0         Current 15 min SES: 0         Current 15 min UAS: 0         Previous 15 min CRC: 0         Previous 15 min LOSW Defect: 0         Previous 15 min ES: 0         Previous 15 min SES: 0         Previous 15 min UAS: 0 Line-0 status Chipset Version:  0 Firmware Version:  R3.0.5 Modem Status:  Data, Status 1 Last Fail Mode:  No Failure status:0x0 Line rate:  1032 Kbps Framer Sync Status: In Sync Rcv Clock Status: In the Range Loop Attenuation:  15.7 dB Transmit Power:  13.5 dB Receiver Gain:  25.5200 dB SNR Sampling:  37.1390 dB Line-1 status Chipset Version:  0 Firmware Version:  R3.0.5 Modem Status:  Data, Status 1 Last Fail Mode:  No Failure status:0x0 Line rate: 1032 Kbps Framer Sync Status: In Sync Rcv Clock Status: In the Range Loop Attenuation:  15.8 dB Transmit Power:  13.5 dB Receiver Gain:  20.2000 dB SNR Sampling:  37.4390 dB Dying Gasp: Present Second CPE sh controllers dsl DSL 0 controller UP SLOT 0: Globespan xDSL controller chipset Frame mode: Utopia Configured Line rate: Auto Line Mode: Two Wire DSL mode: SHDSL Annex B Line Re-activated 0 times after system bootup LOSW Defect alarm: ACTIVE CRC per second alarm: ACTIVE Line termination: CPE         Current 15 min CRC: 0         Current 15 min LOSW Defect: 0         Current 15 min ES: 0         Current 15 min SES: 0         Current 15 min UAS: 0         Previous 15 min CRC: 0         Previous 15 min LOSW Defect: 0         Previous 15 min ES: 0         Previous 15 min SES: 0         Previous 15 min UAS: 0 Line-0 status Chipset Version:  0 Firmware Version:  R3.0.5 Modem Status:  Data, Status 1 Last Fail Mode:  No Failure status:0x0 Line rate:  1288 Kbps Framer Sync Status: In Sync Rcv Clock Status: In the Range Loop Attenuation:  4.8 dB Transmit Power:  11.5 dB Receiver Gain:  18.7420 dB SNR Sampling:  40.8380 dB Dying Gasp: Present Third CPE: sh controllers dsl DSL 0 controller UP SLOT 0: Globespan xDSL controller chipset Frame mode: Utopia Configured Line rate: 2048Kbps Line Mode: Two Wire DSL mode: SHDSL Annex B Line Re-activated 4 times after system bootup LOSW Defect alarm: ACTIVE CRC per second alarm: ACTIVE Line termination: CPE         Current 15 min CRC: 0         Current 15 min LOSW Defect: 0         Current 15 min ES: 0         Current 15 min SES: 0         Current 15 min UAS: 0         Previous 15 min CRC: 0         Previous 15 min LOSW Defect: 0         Previous 15 min ES: 0         Previous 15 min SES: 0         Previous 15 min UAS: 0 Line-0 status Chipset Version:  0 Firmware Version:  R3.0.5 Modem Status:  Data, Status 1 Last Fail Mode:  No Failure status:0x0 Line rate:  2056 Kbps Framer Sync Status: In Sync Rcv Clock Status: In the Range Loop Attenuation:  8.7 dB Transmit Power:  13.5 dB Receiver Gain:  22.5420 dB SNR Sampling:  42.880 dB Dying Gasp: Present thanks, ... View more

Yeah, you illuminate my day Just one point: why sometimes the configured line rate is less than the amount of the line rate? And just to check if i understood well: Configured.rate;line.rate.1;line.rate.2;line.rate.3;line.rate.3;My.comprehension 4608Kbps;1032Kbps;1032Kbps;null;null;"I can have a Max of 4608 but my operator has limited it to 2048Kbps (1032*2)" Auto;1288Kbps;NULL;NULL;NULL;"I can have a Max of 1288Kbps, that the natural capacity of the line (Auto)" 2048Kbps;2056Kbps;NULL;NULL;NULL;"WTF?! I can have more than the capacity lines? Or it is a bad calculation?" Thanks again! Cheers, Greg ... View more