I think I found out why, my router is only having 119808 kb of memory and when it is running, then there is only 8 mb back I think that is the problem, because when I try to install a new packaged the router is loading it in to the ram and also saving it on the flash, and I think it is that there is the problem. pls correct me if I am wrong ... View more

I think that I have found the problem ! it seems to be the switch 2, I have tested it this way: 1. connected the Macbook to the switch 1 and there was no problem ! 2. replaced the switch 2 with at dum cheap D-Link (yes I know it is D-Link )  switch and now it is working, and it have been working the last hours I will test it to tomorrow, and if it is the switch then what can be wrong with my cisco 2940 switch ? would it be better if I make a new post ? ... View more

Hi again I have now tryed the "ip route 0.0.0.0 0.0.0.0 dhcp", but it didn´t help I have also read the discussion that you (Reza Sharifi) recommended, but is it not over wifi the problem is At this point I am lost of idea what it can be, but one thing I found out was that if the Macbook is the only pc on the network, then it works fine ?? Is there how that I can degbu on the router ? I have tryed the degug all, but then my router crashed ... View more

Of course, here it is: R1#sh run Building configuration... Current configuration : 2476 bytes ! ! No configuration change since last restart ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname R1 ! boot-start-marker boot-end-marker ! enable secret 5 xxxxx ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! aaa session-id common ! resource policy ! clock calendar-valid mmi polling-interval 60 no mmi auto-configure no mmi pvc mmi snmp-timeout 180 ip subnet-zero ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 192.168.2.1 ip dhcp excluded-address 192.168.2.2 ip dhcp excluded-address 192.168.2.3 ! ip dhcp pool DHCP-SERVER-LAN-SIDE    network 192.168.2.0 255.255.255.0    default-router 192.168.2.1    dns-server 192.162.153.164 194.239.134.83    domain-name Net ! ! ip ssh version 2 ! ! ! ! ! ! ! ! ! ! ! ! ! ! username xxx secret 5 xxx username xxx password 0 xxx ! ! ! ! interface FastEthernet0/0 ip address dhcp ip nat outside shutdown duplex auto speed auto no cdp enable ! interface FastEthernet0/1 ip address 192.168.2.1 255.255.255.0 ip nat inside duplex auto speed auto ! interface Serial0/0/0 no ip address shutdown no fair-queue clockrate 2000000 ! interface ATM0/1/0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0/1/0.1 point-to-point description Link_To_Outside ip address dhcp ip nat outside logging event subif-link-status atm route-bridged ip pvc 0/101   oam-pvc manage   encapsulation aal5snap ! ! ip classless ! ! no ip http server no ip http secure-server ip nat inside source list 1 interface ATM0/1/0.1 overload ! access-list 1 permit 192.168.2.0 0.0.0.255 ! ! ! control-plane ! ! ! ! ! ! ! banner motd ^C ------------------------------------------------------------ --------------                                     .            .                                     |            |                                    |||          |||                                  .|| ||.      .|| ||.                              .:||| | |||:..:||| | |||:.                                C i s c o  S y s t e m s                                 Kun For Autoriserede!   ------------------------------------------------------------ -------------- ^C ! line con 0 exec-timeout 0 0 password xxx logging synchronous line aux 0 line vty 0 4 logging synchronous transport preferred none transport input ssh ! end This is how it is connected: Router = ATM0/1/0 -> ISP FastEthernet0/1 -> Switch 1 the switches is just configureted as dum switches @layer 2, the only thing there is been changed on the is spanning tree portfast default. Hope this helps ... View more