Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About syedmd866
07-19-2019
Stats
Member since
06-10-2017
10
Posts
0
Helpful
0
Solutions
Created by
syedmd866
in IP Telephony and Phones
in IP Telephony and Phones
07-12-2019
07:03 AM
07-12-2019
07:03 AM
Hi, Please let me know, in few locations our IP phones are going to "preservation mode". Once hangup it is resolving. What is preservation mode ? Thanks.
... View more
04-28-2019
11:53 PM
Hi William, I have created 0[1-9]!# pattern, still call is not dialing instantly after pressing the hash while off hook/speaker. I tried, by using speaker+Dial Num+# and off hook+ Dial Num+# But, it's working on DN#+off hook/speaker. Thanks
... View more
Created by
syedmd866
in IP Telephony and Phones
in IP Telephony and Phones
02-08-2019
04:45 AM
02-08-2019
04:45 AM
Hi Natalie, I'm not expert to give advice, instead of reset you can use 'no voice register pool 10' and configure the pool again. Please rate if you find this helpful.
... View more
02-08-2019
04:33 AM
Hi Sbackus, Please use the command 1). router#sh run | s voice reg copy the output in notepad. and check how many voice reg pools created. If one pool created the configuration similar to below one. Router#sh run | s voice reg voice register global default mode no allow-hash-in-dn max-dn 30 max-pool 1 voice register pool 1 id network xx.xx.xx.xx mask 255.255.0.0 2). Use no voice register pool 1 in config mode, phone will remove from SRST. Finally configure again. Please rate if you find this helpful.
... View more
Created by
syedmd866
in Collaboration, Voice and Video Documents
in Collaboration, Voice and Video Documents
08-16-2018
05:37 AM
08-16-2018
05:37 AM
Hi Lavanya,
How to do this, in phone configuration page only SSH access - Enabled/Disable is there there.
CUCM 9.1
Firmware- sip9951. 9-4-1-9
(2) Go to the Phone’s Phone Configuration page on Cisco Unified Administration Page and locate the “Secure Shell
Information” box:
... View more
06-12-2017
12:46 AM
Hello,
User reported IP phones(9951) are rebooted and not functioned for some time.
How can we find, when the IP Phones are Unregistered/Rebooted.
... View more
06-12-2017
12:33 AM
Hi,
How can we check in CUCM console page(Web GUI).
User is in another place.
... View more
Created by
syedmd866
in IP Telephony and Phones
in IP Telephony and Phones
06-10-2017
09:02 AM
06-10-2017
09:02 AM
Hello ,
Is there any precautions needed before reboot the cluster.
We have 2 sub and 1 pub in a cluster.
Give me a suggestion for rebooting cluster.
... View more
Labels:
Created by
syedmd866
in IP Telephony and Phones
07-12-2019
07-12-2019
Hi, Please let me know, in few locations our IP phones are going to
"preservation mode". Once hangup...
04-28-2019
Hi William,I have created 0[1-9]!# pattern, still call is not dialing
instantly after pressing the h...
Created by
syedmd866
in IP Telephony and Phones
02-08-2019
02-08-2019
Hi Natalie, I'm not expert to give advice, instead of reset you can use
'no voice register pool 10' ...
02-08-2019
Hi Sbackus,Please use the command1). router#sh run | s voice reg copy
the output in notepad.and chec...
08-16-2018
Hi Lavanya, How to do this, in phone configuration page only SSH access
- Enabled/Disable is there t...
06-12-2017
Hello, User reported IP phones(9951) are rebooted and not functioned for
some time. How can we find,...
06-12-2017
Hi Manish, Our cluster is running more then 170 days. And we are facing
issues like call droping,Noi...
Created by
syedmd866
in IP Telephony and Phones
06-10-2017
06-10-2017
Hello , Is there any precautions needed before reboot the cluster. We
have 2 sub and 1 pub in a clus...
Public Statistics
| Date Registered | 06-10-2017 08:32 AM |
| Date Last Visited | 07-19-2019 07:04 AM |
| Total Messages Posted | 10 |
