About FranciscoRC

FranciscoRC · 02-09-2020

Hi everyone.I´m running a lab, simulating ans ISP connected to other ISPs and some clients. eBGP with other ISPs and iBGP and OSPF internally, and everything is working great. Now I´m trying to configure a customer MPLS network with internet access (...

FranciscoRC · 02-07-2019

Hi everyone, I´m doing a lab exercise, and I´m stuck at OSPF configuration...The question I´m trying to answer is:a) Configure OSPFv2 as per the topology diagram and prevent the inadvertent advertisement of OSPFv2 traffic into the VLANs. Summarise ad...

FranciscoRC · 03-10-2017

Hi everyone, I´m doing a project for school about MPLS. The project consists on developing a tool using SNMP to query network devices (in this case routers) for information(MIBS) about MPLS and doing a simple web page showing it. I´ve never worked ...

FranciscoRC · 12-18-2015

At headquarters I have an Cisco ASA 5520 and I´m trying to connect Site-to-Site VPN with the RV130W . My headquarters is subnet 10.0.0.0/8 and my sites subnet are 192.168.X.0/24 [x is the site number]. I´m new at the company and the previous guy set...

FranciscoRC · 05-14-2015

Hello Everyone, To start let me thanking you for reading this post.I have an ASA 5520 and, until yesterday everything was working perfectly, then "magically" I started getting this message, an all VPN Site-to-Site links can´t connect.I have a public ...

FranciscoRC · 02-08-2019

Jon, Thank you so much for your reply.My doubt was in using it with point-to-point links on the routers. If R2 is the DR how would LSAs flow between R2 and the switches?Final question, Can I use "ip ospf network point-to-point" interface configurati...

FranciscoRC · 03-23-2017

Hi, Let me start by thanking you for your help. I was planning to map the IPv4 / IPv6 topology and the MPLS topology, by starting at a router get his information (model, version, interfaces, routing table, BGP, MPLS, etc.) and next jumping to th...

FranciscoRC · 03-26-2015

Hi Vivek Thank you so much, I would never get there without your help. Thanks to you I think I´m understanding how CMExpress works.Setting the cor on dial-peer as outgoing OK I get it, but in my mind it made no sense in applying the cor in incoming f...

FranciscoRC · 03-25-2015

Hi Vivek,Sorry but I´m not understanding what you are saying. I´ve changed the COR from outgoing to incoming and add the same COR to outgoing in ephone-dn, like the example below but I can´t make it work. If you could please give me an example code. ...

FranciscoRC · 03-25-2015

Hi Vivek, Your help, was so precious...I´ve done the configuration you suggested, and everything is working perfectly (almost). I think now I understand a bit how this works.The only detail missing is how to deny/permit extensions on dial peers. For ...

Member Since	‎03-13-2008 06:31 PM
Date Last Visited	‎02-19-2020 10:17 AM
Posts	15

User Statistics

User Activity

MPLS - VRF internet access with NAT

OSPF Network Configuration

What is important on a router about MPLS?

RV130W Site-toSite VPN (add a second policy)

ASA 5520 - "Duplicate first packet detected. Ignoring packet."

Re: OSPF Network Configuration

Hi,

Hi Vivek Thank you so much, I

Hi Vivek,Sorry but I´m not

Hi Vivek, Your help, was so