Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Evgeniy Prichinin
09-04-2019
Stats
Member since
04-12-2013
99
Posts
24
Helpful
8
Solutions
Created by
Evgeniy Prichinin
in MPLS
in MPLS
08-31-2019
10:17 PM
08-31-2019
10:17 PM
What kind of traffic flows into l2vpn? fat label is used to load balancing mpls traffic in bundle-ethers between mpls routers, so it will not help.
... View more
Created by
Evgeniy Prichinin
in XR OS and Platforms
in XR OS and Platforms
08-24-2019
09:04 AM
08-24-2019
09:04 AM
There are two ways: 1) Install add/activate. Could be done using ISSU in some cases. 2) turboboot.
... View more
Created by
Evgeniy Prichinin
in XR OS and Platforms
in XR OS and Platforms
08-24-2019
09:00 AM
08-24-2019
09:00 AM
Better to use bgp route refresh instead of soft reconfiguration.
... View more
Created by
Evgeniy Prichinin
in MPLS
in MPLS
08-17-2019
12:08 AM
08-17-2019
12:08 AM
Hello. It should work according to https://community.cisco.com/t5/service-providers-documents/asr9000-xr-load-balancing-architecture-and-characteristics/ta-p/3124809#case1. But i noticed that you use dst-ip hash in bundle-ether. I think you should disable this setting and use default. Also you could exclude l4 info from hash by configuring cef load-balancing fields L3 global
... View more
Created by
Evgeniy Prichinin
in Other Service Provider Subjects
in Other Service Provider Subjects
08-16-2019
02:21 AM
08-16-2019
02:21 AM
Try to set ip nat settings pap limit 30 bpa also you could set timeout for connections.
... View more
08-15-2019
09:21 PM
It will work for traffic between A and B, but not for ISP2 traffic directed to A. Using Backup community from ISP2 is only way to achive using ISP2 as backup.
... View more
08-15-2019
09:16 PM
You should move to p2p networks. After that you can tune hello/dead-intervals and enable BFD. Using broadcast segments are very bad in mpls environment.
... View more
Created by
Evgeniy Prichinin
in XR OS and Platforms
in XR OS and Platforms
07-19-2019
03:16 AM
07-19-2019
03:16 AM
Hello. All answers are available in article. https://community.cisco.com/t5/service-providers-documents/migrating-from-rsp440-to-rsp880-on-asr9000/ta-p/3157251
... View more
Created by
Evgeniy Prichinin
in Routing
in Routing
06-20-2019
09:16 PM
06-20-2019
09:16 PM
It's possible to renew CCNP R&S with any Professional exam until feb 2020.
... View more
04-24-2019
02:38 AM
Output of command show mls stat shows a lot of errors related to MTU. Also you can add no ip redirects no ip proxy-arp no ip unreachable to all L3 interfaces.
... View more
04-18-2019
08:39 AM
show ip traffic show int Po8 switching show int Te1/0/1 switching show run int po8 show run int te1/0/1 show run int vlan4085 show run int vlan4035 btw.. there are a lot of TTL failures MTU failures No-route packet drops do you have mls rate-limit all ttl-failure 100 10 mls rate-limit all mtu-failure 100 10 in config?
... View more
04-11-2019
02:04 AM
What kind of cache server do you use? In what way traffic is directed to cache server ? PBR ?
... View more
Created by
Evgeniy Prichinin
in Switching
in Switching
04-07-2019
06:50 AM
04-07-2019
06:50 AM
Connect switches using stack cables than use the command switch 2 renumber 3.
... View more
04-07-2019
05:51 AM
Hello, you can use netdr to dump traffic directed to CPU. After that may be you get an idea about configuration that cause high cpu load.
... View more
Created by
Evgeniy Prichinin
in MPLS
08-31-2019
08-31-2019
What kind of traffic flows into l2vpn? fat label is used to load
balancing mpls traffic in bundle-et...
08-24-2019
There are two ways:1) Install add/activate. Could be done using ISSU in
some cases.2) turboboot.
Created by
Evgeniy Prichinin
in MPLS
08-17-2019
08-17-2019
Hello. It should work according to
https://community.cisco.com/t5/service-providers-documents/asr900...
Created by
Evgeniy Prichinin
in Other Service Provider Subjects
08-16-2019
08-16-2019
Try to set ip nat settings pap limit 30 bpaalso you could set timeout
for connections.
08-15-2019
It will work for traffic between A and B, but not for ISP2 traffic
directed to A. Using Backup commu...
08-15-2019
You should move to p2p networks. After that you can tune
hello/dead-intervals and enable BFD.Using b...
Created by
Evgeniy Prichinin
in XR OS and Platforms
07-19-2019
07-19-2019
Hello. All answers are available in article.
https://community.cisco.com/t5/service-providers-docume...
Created by
Evgeniy Prichinin
in Routing
06-20-2019
06-20-2019
It's possible to renew CCNP R&S with any Professional exam until feb
2020.
04-24-2019
Output of command show mls stat shows a lot of errors related to
MTU.Also you can add no ip redirect...
04-18-2019
show ip trafficshow int Po8 switchingshow int Te1/0/1 switchingshow run
int po8show run int te1/0/1s...
04-11-2019
What kind of cache server do you use?In what way traffic is directed to
cache server ? PBR ?
Created by
Evgeniy Prichinin
in Switching
04-07-2019
04-07-2019
Connect switches using stack cables than use the command switch 2
renumber 3.
Public Statistics
| Date Registered | 04-12-2013 03:08 AM |
| Date Last Visited | 09-04-2019 01:41 AM |
| Total Messages Posted | 99 |
| Total Helpful Votes Received | 24 |
Helpful Votes From
