Is there any specfications I should be looking for when buying a Microwave oven. The question being is one better then another for interfernce on my WLAN? Thanks ... View more

I have a remote location with 4 AIR-CAP3502E-A-K9 (AP01,AP02, AP03, AP04)  ver 2.0 with 8 SSIDs   2 ea. AIR-ANT5135DG-R (DISABLED) and 2 ea. AIR-ANT2422DG-R (ENABLED)  I have no b clients and few g clients ( 4 ea. LXE XV6 used very lightly) and a very few N clients (mostly laptops maybe 1 month for 1/2 hr.) I have a 4404 controller ver. 7.0.98.0    AP03              MAC C4:0A:CB:DF:AD:6F      Channel 36  (Rate 6,9,12, 18, 24, 36, 48, 54) AP03             "                                        "6E      Channel 36  "                                                     " AP03             "                                        "61       Channel 11  (Rate 2, 5.5, 6, 9, 11, 12, 18, 24, Ext 36, 48, 54) AP03             "                                        "60       Channel 11  "                                                                                "        AP03 (MAC 6E) channel agility: No Network mode: Infrasture Preamble: long #STA#: 0 PCF/DCF: DCF Cell Power: dBm 17 APO3 (MAC 61) channel agility: No Network mode: Infrastruture Preamble: short # STA: 0 PCF/DCF: DCF Cell Power: dBm 20 I have set the radio policy to "all"  so it can operate at 2.4 & 5 GHz Range (What should it be set at?) I have two alerts 1) AP PHY data rate anomaly: user date rates of 48M and 54M is not included in the user defined date rate 2) Missing Performance Options: does not support 802.11b optional capability (/packet-binary-convoltional coding/channel agility) I'm also showing overlapping legacy BSS condition exists on channels 1) beacon legacy BSS on channel 9 2.4 GHz within range of an HT (20 MHz) AP on channel 13, HT (40 MHz) on channel 13 & HT (40 MHz lower)ch 14 2) "                                      "channel 6 2.4 GHZ "                                                              "channel 10  HT (40 Mhz) on channel 10 & HT  (40 MHz Lower) ch 14 3) "                                     " channel 1 2.4 GHz "                                                               " channel 5  HT (40 Mhz) on channel 13 & HT (40 MHz Lower) ch 9 How do I seperat by operating channels? Thanks ... View more

I did a scan using the airmagnet WiFi anaylizer and it informed me that the one of the alarms is the following AP PHY Data Rate Anomaly: APs are using data rates of 48M, 54,M which is not included in the user defined data that is allowed in the system. I checked the controller and I have both those data rates enabled? Thanks       ... View more

What would be the ramnifactions of using AIR-1242AG-A-K9 (g radios only: no b clients) and AIR-LAP1231G-AK9 (g radios: only no b clients) with AIR-ANT1728 (non diversity antennas) on the WLAN. Some of the APs 1242/ 1231 will be with in line of site of each other.  Thanks Tom ... View more

This might be a stupid question: I have 7 AIR-LAP 1231G-A-K9 APs: I have two of them up and working and the other 5 turned off: The vendor (before I was here) had a answer to every problem: add more APs. I know it's hard to believe. The WLC shows the five APs (Admin Status: disabled and Opertional Status disabled)I'm still recieving interference on the other two live AP's. The question: Could the five APs that are disabled still cause interference? Thanks Tom ... View more