Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About VictorCL59
Stats
Member since
05-08-2012
33
Posts
5
Helpful
0
Solutions
12-12-2013
02:51 AM
Hello everybody. Can't find out about one thing. On cisco.com I have read the next about ISM-VPN-29 module for my C2911 "The Cisco 2900 Series Module (ISM-VPN-29) can provide hardware-based IPSec encryption services of 145 and 550 Mbps in the Cisco 2901, 150 and 600 Mbps in the Cisco 2911, 220 and 700 Mbps in the Cisco 2921, and 385 and 900 Mbps in the Cisco 2951 (IPSec IMIX and 1400-byte packets)." There are two speeds "150 and 600 Mbps in the Cisco 2911". For what? And why the differance is so big? Please explain me.
... View more
Labels:
11-13-2013
04:15 AM
I saw this page. I read many about licenses for ISR G2. And I know I need it in any bundle but for C3925-WAASX-SEC/K9 thich is with WAN services I don't know. I suppose that I need but want to be sure. I'm continuing to looking for answer. If I find out about it faster I'll report about it here. But hope that somebody will answer me here
... View more
11-13-2013
03:50 AM
Hello. I have only one question. Do I need for C3925-WAASX-SEC/K9 addtional license SL-39-DATA-K9 for IP SLA ? SL-39-DATA-K9
... View more
Labels:
05-15-2013
06:38 AM
Hello. Maybe someone has already had experience in such case. I have Cisco ISR 861-SEC/K9 with usual configuration – NAT, PAT, ACL, ZBFW, VPN Site-to-Site. It’s nice one and cheap and very similar to Cisco 881 ) But when I have 10-12 Mbit/s in outgoing direction (to Internet without encryption – only routing, NAT, Firewall) and about 1-2Mbit/s in inbound I have problem. I even don’t have any VPN traffic at this time. I have 5-10-15% packets drop. CPU utilization is about 45-50%. Memory is enough. May be this is normal when CPU load reaches 90-95% but not at 50% - it’s not normal. Please, Can you suggest me something in this situation. Thanks
... View more
Labels:
Created by
VictorCL59
in Server Networking
in Server Networking
03-13-2013
04:44 AM
03-13-2013
04:44 AM
Hi. I'm Victor and I need your help. Please give me advise. I have to place servers in to different datacenters for HA. There will be cluster of Hyper-V nodes. One node in one DC and another in the second DC. If connection to main DC or virtual machine in first node in this DC fails this virtual machine will startup in the second DC. I have seen topology like this http://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns224/ns949/ns304/ns975/data_center_interconnect_design_guide.pdf on page 13. DCs will be have L2 link between each other. But in one DC I have one global IPs and in another DC I have different global IP for virtual machines. We have many clients ~ 1000 and more. it won't be efficient to change IPs on all clients in case of failure on mail DC. Do I need my own AS and BGP in this two DCs with my own IPs that will be connected by L2 link? How can I do it without AS? Can somebody suggest me something where I can find some answer on my question (literature, guides)?
... View more
Labels:
02-20-2013
11:40 PM
thanks for you answer and suggestion. May be I could find some IPv4 space at least with /24 prefix. thanks a lot again
... View more
02-20-2013
02:06 AM
Hello everyone. I'm Victor from Ukraine and I need you suggestion. Our company is going to have it own datacenter with several racks, We need our own global AS with PI prefix but as you know RIR won't assign to as a IPv4 prefix. So we just can ask for IPv6 prefix to have some kind of /48. One big question! How will our clients in Ukraine/world with only IPv4 addresses access our servers that are only on IPv6 from their home and office places? There are a lot of translation mechanisms but we additionally need some scope of IPv4 for it - yes? If yes, we need PA IPv4 addresses and if ISP who gives us these ones, will loose with our DC connection, we loose this translation ipv6ipv4 it looses any senses about our AS with BGP as redundant mechanisms for High Availability. How do people in the USA do this? Thanks.
... View more
Labels:
01-15-2013
10:24 PM
The same problem with Cisco 2911-K9 Security licence. There are all routing protocols: bgp,eigrp,ospf,rip and some extra. All routing work but rip not )! I have upgraded IOS from 15.1 to 15.3 and there is no result. But I try to configure RIP with Cisco Configuration Professional and it's working on all devices - CISCO 881, CIsco 891, Cisco 2911. It's funny ) I suppose that there some CLI bug with "router rip" command on the routers.
... View more
01-11-2013
07:49 AM
I have comand "router rip". When I type "router rip" I go to rip configuration level where I type network commands, no auto-summary and so on as usual but I can't see these commands in run-config, and it doesn't work. I've also read that this router has rip with any license and it has but it doesn't work. May be I'll upgrade to new ios. By the way. When I upgrade cisco router ISR G2 to new IOS, then do I need to recover some lisence or just upgrade and it's done? I have never upgraded ISR G2 until now )
... View more
01-11-2013
02:37 AM
I have bought Cisco ISR 881 C880DATA-UNIVERSALK9-M with c880data-universalk9-mz.150-1.M7.bin ios. command "show ver" tell me: License Information for 'c880-data' License Level: advsecurity Type: Permanent Next reboot license Level: advsecurity So I have advsecurity On cisco site there was a thing http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78_459542_ps380_Products_Data_Sheet.html section "Table 5. Cisco IOS Software Features on Cisco 880 Series: Advanced Security Feature Set (Default)" that tell me I have RIP protocol to use. But when I type "router rip" command and sub router sommands like: network, passive-interface, redistribution. There are no in runnning-config such things after all I've done. It have not been saved. then the command "show licence": #show license Index 1 Feature: advipservices Period left: Not Activated Period Used: 0 minute 0 second License Type: EvalRightToUse License State: Not in Use, EULA not accepted License Count: Non-Counted License Priority: None Index 2 Feature: advsecurity Period left: Life time License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: Medium I need even RIPv2 to have simple routing information to exchange. And I don't know. Cisco 880 series is G2 or G1. Cisco ISR beggining from 890 series is G2. About 880 I don't know. There no informanion about it or at least I have not found it yet. On one 891 is the same problem. When I type "router eigrp 1" everything is great. But when "router rip" - do no work. Please help.
... View more
Labels:
12-19-2012
04:24 AM
Hello everybody. I need to configure Cisco router like a L2TP/IPSec client to connect to remote VPN server. I have foung some articles but It doesn't work. May be someone has a working config ? Please help.
... View more
Labels:
11-27-2012
02:17 AM
Hi. Does anyboby have a default xml config file for cisco ip phone 6921? I have to set it up, but can not find example of this file. There are no web or phone menu on this phone to set it up like on 79xx series. Please share how has one. Thanks.
... View more
Labels:
11-23-2012
04:58 AM
Hello. May be it is stupid question, but anyway. There is "Site-to-Site VPN User Sessions limit" to every Cisco ASA description. I am confused about it. For example, in http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html#~tab-b Cisco ASA 5520 has Maximum Site-to-Site and IPsec IKEv1 Client VPN User Sessions = 750. So it is… Is it a limit for count of Site-to-Site VPN channels or it is a user sessions limit in one VPN tunnel?
... View more
Labels:
12-12-2013
Hello everybody.Can't find out about one thing.On cisco.com I have read
the next about ISM-VPN-29 mo...
11-13-2013
I saw this page. I read many about licenses for ISR G2. And I know I
need it in any bundle but for C...
11-13-2013
Hello.I have only one question.Do I need for C3925-WAASX-SEC/K9
addtional license SL-39-DATA-K9 for ...
05-15-2013
Hello.Maybe someone has already had experience in such case.I have Cisco
ISR 861-SEC/K9 with usual c...
Created by
VictorCL59
in Server Networking
03-13-2013
03-13-2013
Hi.I'm Victor and I need your help.Please give me advise.I have to place
servers in to different dat...
02-20-2013
thanks for you answer and suggestion.May be I could find some IPv4 space
at least with /24 prefix.th...
02-20-2013
Hello everyone.I'm Victor from Ukraine and I need you suggestion.Our
company is going to have it own...
01-15-2013
The same problem with Cisco 2911-K9 Security licence.There are all
routing protocols: bgp,eigrp,ospf...
01-11-2013
I have comand "router rip". When I type "router rip" I go to rip
configuration level where I type ne...
01-11-2013
I have bought Cisco ISR 881 C880DATA-UNIVERSALK9-M with
c880data-universalk9-mz.150-1.M7.bin ios.com...
12-19-2012
Hello everybody.I need to configure Cisco router like a L2TP/IPSec
client to connect to remote VPN s...
11-27-2012
Hi.Does anyboby have a default xml config file for cisco ip phone 6921?I
have to set it up, but can ...
Public Statistics
| Date Registered | 05-08-2012 05:47 AM |
| Date Last Visited | 08-18-2017 04:00 AM |
| Total Messages Posted | 33 |
| Total Helpful Votes Received | 5 |
