Cisco Community
English
Register
Make a difference. Your participation will help fund Save the Children. LEARN MORE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Aditya Sharma
‎02-03-2021

Cisco Employee
Recent Badges
Awards
Recent Badges
See all
1 Accepted Solution
30 Helpful Vote
10 Helpful Vote
1 Helpful Vote
10 Replies
5 Replies
Stats
Member since ‎02-08-2012
16
Posts
20
Helpful
3
Solutions

Re: BIOS Update Failed: Unable to flash new BIOS Image

Created by in Unified Computing System Discussions
10-17-2017
10-17-2017
good question! If these are M2 blades then please check out this defect and try applying the 2nd wor...

Som,Its possible your hitting

Created by in Unified Computing System Discussions
01-11-2015
01-11-2015
Som,Its possible your hitting a know cisco defect. Try doing this:uncheck TLS 1.2 setting under adva...

Re: ESXi 5.1 Update 1 with UCS B and C Series

Created by in Unified Computing System Discussions
05-16-2013
05-16-2013
5.1U1 support also depends on the type of blade that you may have as well.

Power state on Chassis # is redundancy-failed

Created by in Unified Computing System Discussions
05-16-2013
05-16-2013
Please open a TAC case as Kenny suggested, but also look in to the following known defect and applyi...

Recovery of a "failed" VDC

Created by in Switching
05-16-2013
05-16-2013
I believe to reload a nondefault virtual device context (VDC), use the reload vdc command. reload vd...

Moving profile from C200M2 to C220M3 - Windows not happy.

Created by in Unified Computing System Discussions
04-22-2013
04-22-2013
Few questions for you:What is your CIMC firmware of C200m2 and C220M3 servers? What is your UCSM fir...

Re: boot from san, array not seeing wwpn

Created by in Unified Computing System Discussions
12-22-2012
12-22-2012
Useful link:http://www.cisco.com/en/US/docs/unified_computing/ucs/ts/guide/TS_SANBootAndConnect.pdf

Re: UCS C210 M2 not working!!

Created by in Unified Computing System Discussions
11-30-2012
11-30-2012
Hello, Restart your server by physically pulling the plug to get connectivity back, and open a TAC c...

Nexus1010 MGMT MAC address issue

Created by in Unified Computing System Discussions
11-24-2012
11-24-2012
Can you please provide the output from these commands from both 1010s:- show interface mgmt 0- show ...

show tech support hanging at initiating.

Created by in Unified Computing System Discussions
11-24-2012
11-24-2012
Please, use this link to download the TechSupport from the UCS: http://www.cisco.com/en/US/docs/unif...

write cache battery backup ucs b200 m2 blade

Created by in Unified Computing System Discussions
11-24-2012
11-24-2012
Robert,Depending on your LSI Controller but please review this B200-m3 Spec Sheethttp://www.cisco.co...

ESXI 5.1 Problem

Created by in Unified Computing System Discussions
11-24-2012
11-24-2012
I dont think C22-m3s's support ESXi 5.1. Please, refer to Cisco's UCS HW and SW Interoperability mat...

Speed of Uplink port question

Created by in Unified Computing System Discussions
10-31-2012
10-31-2012
To my knowledge, you can configure FC uplink port's speed in a similar way, as you would for Etherne...

vSphere 5.1 on Cisco UCS 5108

Created by in Unified Computing System Discussions
10-30-2012
10-30-2012
Amit,I completely understand your point of view, but at the end of the day the decision of upgrading...

step by step implementation plan for UC on UCS

Created by in Unified Computing System Discussions
10-29-2012
10-29-2012
Brent,I dont know if you implementing UC on UCS B or C series servers, but here are some links that ...
Public Statistics
Date Registered ‎02-08-2012 12:20 PM
Date Last Visited ‎02-03-2021 09:21 AM
Total Messages Posted 16
Total Helpful Votes Received 20
Helpful Votes From