Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About LiWenbin2008
05-29-2019
LiWenbin2008
Member since
08-02-2011
Beginner
01-21-2013
11:48 PM
Take another lower version IOS to solve the issue , Thanks a lot.
... View more
01-21-2013
10:34 PM
Thanks leolaohoo, it's just a example. I have solved the issues with another version IOS: c3560e-ipbasek9-mz.122-58.SE2.bin. I don't know what's the difference between c3560e-ipbasek9-mz.122-58.SE2.bin and c3560e-universalk9-mz.150-2.SE.bin, why the c3560e-universalk9-mz.150-2.SE.bin cann't boot the system?
... View more
01-21-2013
08:44 PM
I have tested "boot usbflash0:3750.bin" , failed either , the same error. In cisco.com IOS download page, there are some *.tar files with the same version. Is there any differences? Sent from Cisco Technical Support iPhone App
... View more
01-21-2013
06:05 PM
I have checked it , it's the right IOS. There's the *.bin file in the flash only, is this enough for boot ? Sent from Cisco Technical Support iPhone App
... View more
01-21-2013
06:01 PM
I have a 3560x switch with the flash formatted . I have tried to solve the problem by copying the IOS file to the flash. But the boot failed either . I have tried to copy the same IOS by the Xmodem, The boot failed again. My question is how to fixed the boot issues after the flash was formatted? Thanks! Sent from Cisco Technical Support iPhone App
... View more
Labels:
01-21-2013
05:01 PM
Anyone have the same problem? The guide in cisco.com, I have tried, failed again. Sent from Cisco Technical Support iPhone App
... View more
01-21-2013
05:45 AM
1.When the switch is POSTing, I press the MODE button. At the rommon mode, I use the " format flash:" to format the flash. 2.Then I take a USB Device insert into the switch, and take "format usbflash0:" to format the USB device. 3. I copyed the "*.bin" to the USB by my PC , and then copy the IOS file to the switch. 4.After type the "boot" , a long time later , the cli common show the error log "Boot process failed". Anyone can help me ? Thanks. My IM(Tecent QQ 443408372) I have tested the XMODEM way to update the IOS , Failed ... ,and the same error. I have download the *.lic file from the cisco.com , I don't know if it's related? INFO ------------------------------------------------- switch: set BAUD=115200 BOARD_CONFIG_REV=0 BOOT=flash:c3560e-universalk9-mz.150-2.SE.bin CLEI_CODE_NUMBER=COMJN00ARC DAUGHTERBOARD_ASSEMBLY_NUM=800-32786-02 DAUGHTERBOARD_SERIAL_NUM=FDO163501E8 DEFAULT_ROUTER=192.168.1.101 MAC_ADDR=FC:99:47:EC:36:80 MODEL_NUM=WS-C3560X-48T-S MODEL_REVISION_NUM=A0 MOTHERBOARD_ASSEMBLY_NUM=73-12556-06 MOTHERBOARD_REVISION_NUM=A0 MOTHERBOARD_SERIAL_NUM=FDO16341YFP SDM_TEMPLATE_ID=0 SWITCH_PRIORITY=1 SYSTEM_MTU=1530 SYSTEM_SERIAL_NUM=FDO1604P06F TAN_NUM=800-31330-03 TAN_REVISION_NUMBER=B0 VERSION_ID=V03 boot=flash:c3560e-universalk9-mz.150-2.SE.bin -- MORE -- switch: switch: boot Loading "flash:c3560e-universalk9-mz.150-2.SE.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ File "flash:c3560e-universalk9-mz.150-2.SE.bin" uncompressed and installed, entry point: 0x3000 executing... Loading "flash:/c3560e-universalk9-mz.150-2.SE.bin"...@@@@@@@@@@@@@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ File "flash:/c3560e-universalk9-mz.150-2.SE.bin" uncompressed and installed, entry point: 0x3000 executing... Boot process failed... switch:
... View more
Labels:
10-25-2011
01:22 AM
Hi Arshad Khan, your configration have some thing wrong. Please remove the log tag from you access-list! Because access-list with log in switch ,it won't work . Log could only used for route-control logging.
... View more
10-24-2011
10:38 PM
hi,everybody! I have several questions about PfR when I read the cisco's documents.Here is the example Q1: enable configure terminal ip access-list extended Voice_Traffic 10 permit udp any 10.1.0.0 0.0.255.255 range 16384 32767 exit pfr-map Voice_MAP 10 match ip address access-list Voice_Traffic set active-probe jitter 10.1.1.1 target-port 1025 codec g711alaw set delay threshold 300 set mos threshold 3.76 percent 30 set jitter threshold 15 set loss relative 5 resolve mos priority 1 resolve jitter priority 2 resolve delay priority 3 resolve loss priority 4 Here match ip address acess-list , we can also config as "match traffic-class Voice_Traffic access-list Vioce_Traffic", Is there any differences ? ------------ Q2: PfR master policy-rule Voice_MAP mode route control mode monitor both mode monitor metric static tag 2012 learn throghput delay I have configed the Policy-rule on PfR master. when I hope PfR can operate normally, Is that all ? Need I do redistribution on PfR border router as : route-map PfR match tag 2012 router eigrp 90 redistribute static route-map PfR Thanks !
... View more
Labels:
10-24-2011
09:49 PM
hi,everybody! I have several questions about PfR when I read the cisco's documents.Here is the example Q1: enable configure terminal ip access-list extended Voice_Traffic 10 permit udp any 10.1.0.0 0.0.255.255 range 16384 32767 exit pfr-map Voice_MAP 10 match ip address access-list Voice_Traffic set active-probe jitter 10.1.1.1 target-port 1025 codec g711alaw set delay threshold 300 set mos threshold 3.76 percent 30 set jitter threshold 15 set loss relative 5 resolve mos priority 1 resolve jitter priority 2 resolve delay priority 3 resolve loss priority 4 Here match ip address acess-list , we can also config as "match traffic-class Voice_Traffic access-list Vioce_Traffic", Is there any differences ? ------------ Q2: PfR master policy-rule Voice_MAP mode route control mode monitor both mode monitor metric static tag 2012 learn throghput delay I have configed the Policy-rule on PfR master. when I hope PfR can operate normally, Is that all ? Need I do redistribution on PfR border router as : route-map PfR match tag 2012 router eigrp 90 redistribute static route-map PfR Thank you !
... View more
Labels:
Created by
LiWenbin2008
in Routing
01-21-2013 10:34 PM
01-21-2013 10:34 PM
Thanks leolaohoo, it's just a example.I have solved the issues with
another version IOS:c3560e-ipbas...
Created by
LiWenbin2008
in Routing
01-21-2013 08:44 PM
01-21-2013 08:44 PM
I have tested "boot usbflash0:3750.bin" , failed either , the same
error.In cisco.com IOS download p...
Created by
LiWenbin2008
in Routing
01-21-2013 06:05 PM
01-21-2013 06:05 PM
I have checked it , it's the right IOS.There's the *.bin file in the
flash only, is this enough for ...
01-21-2013 06:01 PM
I have a 3560x switch with the flash formatted . I have tried to solve
the problem by copying the IO...
Created by
LiWenbin2008
in Routing
01-21-2013 05:01 PM
01-21-2013 05:01 PM
Anyone have the same problem? The guide in cisco.com, I have tried,
failed again.Sent from Cisco Tec...
Created by
LiWenbin2008
in Routing
01-21-2013 05:45 AM
01-21-2013 05:45 AM
1.When the switch is POSTing, I press the MODE button. At the rommon
mode, I use the " format flash:...
10-25-2011 01:22 AM
Hi Arshad Khan, your configration have some thing wrong. Please remove
the log tag from you access-l...
10-24-2011 10:38 PM
hi,everybody! I have several questions about PfR when I read the cisco's
documents.Here is the examp...
Public Statistics
| Date Registered | 08-02-2011 08:32 PM |
| Date Last Visited | 05-29-2019 12:06 AM |
| Total Messages Posted | 9 |
