Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About delahais
Stats
Member since
02-18-2003
137
Posts
5
Helpful
1
Solution
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
05-07-2014
01:47 AM
05-07-2014
01:47 AM
Hi, Recently under VIF paths tab, on 3 different UCS domains, I did noticed that some virtual circuits were notified "unpinned". It was under 3 different UCS domain running 2.1(1a), 2.2(1b) and 2.1(3b). In order to correct, the issue : - first time, I have unassociated the Service Profile + re acknowledged the blade + re associated the SP ; I have to do that for few SP from 2 chassis. - second time, we have reload the IOM-B : for some blades/SP from a same chassis (but not all blade), all vEth/vFC were unpinned for the IOM-B - the third time, please see the photo in attach, both vFC are unpinned for several SP... it is impossible, the ESXi hosts on the blade do work.... the ESXi 5.1 is configured on BootOnSan.... so the VIF paths must to work correctly. At present, for this third case, I done any action but it is not clear to have these "unpinned" state. ... it seems to me that it is a cosmetic error Any idea or any same feedback about unpinned vNIC/vFC state are welcome. Many thx. Nicolas.
... View more
- Tags:
- unpinned
Labels:
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
04-18-2014
01:52 PM
04-18-2014
01:52 PM
The zoning was ko, so the B200M3 did not see any LUN (no local disk) Many thank Nicolas. PS : previously, I do remember the B-serveur does not go to bios... it just returned an error message.... more explicite.
... View more
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
04-17-2014
01:26 PM
04-17-2014
01:26 PM
I just created and associated a new SP to a B200M3. When i check the boot server via the vConsole, i can see that the B200 switch to BIOS "gui interface". If i try to go out the bios, the B200M3 switch back to bios.... in short, i can not leave the bios GUI intercace. I do not configure any bios policy (so = default) The B200M3 is less local disk ; the SP must boot on SAN Any ideas are welcome BR
... View more
Labels:
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
04-15-2014
12:58 AM
04-15-2014
12:58 AM
Hi, What is the board controller ? what it do ? I have to upgrade a UCS domain with 12 B200M3 to UCSM 2.2(1b) : do i need to upgrade the board Controller ??? which version to choose : 11, 5 or 8 ??? Any piece of information about bord Controller is welcome. Many thx. BR. Nicolas. PS : snapshots in attachement.
... View more
Labels:
Created by
delahais
in Other Data Center Subjects
in Other Data Center Subjects
04-04-2014
01:18 AM
04-04-2014
01:18 AM
Many thanks for your reply. BR
... View more
Created by
delahais
in Other Data Center Subjects
in Other Data Center Subjects
03-31-2014
02:29 AM
03-31-2014
02:29 AM
Hi, We have a fabric composed by 2 Nexus 6004. The links between the 2 Nx 6004 are configured with vE_ports. What is the maximum length for the links between the 2 Nexus 6004 ? Many thanks in advance. Nicolas.
... View more
Labels:
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
03-09-2014
04:22 PM
03-09-2014
04:22 PM
Hello Kenny, My main question is « how to use and to configure failover on VIC 1225 ». I have already configure failover on B-serie but never on c-series For more details (please see diagram in attach), my issue is that my C240 on DRP site (just 40 metres from main site) is connected to local switch (C3560) and to LAN core (C4506 on main site). This connection on 2 Catalyst devices seems to be a problem for vSphere : i could see that : as soon as I connect the 2 ports, C240 lost connection to vCenter ; CIMC is still pinging. I could read on ucsguru forum, someone has the same issue with 2 catalyst. I do not have a lot of time for this deployment and installation. So, I told me to use actif/passif should be the faster way. If I connect only a cable (by shuting/ no shuting an interface on a catalyst), it works. In order to do that, automatically, I would want to implement failover on VIC1225 Any suggestion on my issue is welcome. Many thanks. Nicolas.
... View more
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
03-07-2014
03:24 AM
03-07-2014
03:24 AM
Hi, I have a C240M3 with a VIC 1225. I would want to enable failover. In order that, i have to enable NIV mode. But it seems to me that i could not. Why ???? how to solve this issue ??? ########################################## C240-FCH1749V0VC /chassis/adapter # set cli CLI options description Adapter description fip-mode Enable/disable FIP vntag-mode Enable/disable VNTAG ########################################## niv-mode not present..... ########################################## C240-FCH1749V0VC /chassis # show adapter 2 detail PCI Slot 2: Product Name: UCS VIC 1225 Serial Number: FCH17457ESH Product ID: UCSC-PCIE-CSC-02 Adapter Hardware Revision: 6 Current FW Version: 2.1(3a) VNTAG: Disabled FIP: Enabled Configuration Pending: no CIMC Management Enabled : yes VID: V03 Vendor: Cisco Systems Inc Description: Bootloader Version: 2.1(3a) FW Image 1 Version: 2.1(3a) FW Image 1 State: RUNNING ACTIVATED FW Image 2 Version: 2.1(3a) FW Image 2 State: BACKUP INACTIVATED FW Update Status: Idle FW Update Error: No error FW Update Stage: No operation (0%) FW Update Overall Progress: 0% C240-FCH1749V0VC /chassis # ########################################## any detail on NIV My C240 is connect to Catalyst 3750. Many thx. Nicolas.
... View more
Labels:
03-06-2014
01:44 PM
Hi Richard, Hi Wdey, First of all thks for your replies Who is right ??? I am used to use npv/npiv with Nx 5k. I would want do the same config but with Nx 7k,as Wdey said. I do not have any experience on vdc storage. + At present, i can test on a 7k By reading, i can find information as said Richard. all doc said "regular fabric", not npv/npiv. + i could read only mds devices is allowed to connect with E ports... not broadcade fabric.... who is right ? I am very amazed about that. Why ???? Thx Nicolas.
... View more
03-05-2014
02:44 PM
hi guys, Is-it possible to configure a storage vdc in npv mode ? We "just" want to consolidate access I/O... C7HP Blade with Nx2232 connected to Nx7010 with storage vdc connected to MDS (FCF)... Many thanks. Nicolas.
... View more
Labels:
03-05-2014
02:41 PM
hi guys, Is-it possible to configure a storage vdc in npv mode ? We "just" want to consolidate access I/O... C7HP Blade with Nx2232 connected to Nx7010 with storage vdc connected to MDS (FCF)... Many thanks. Nicolas.
... View more
Labels:
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
02-26-2014
01:24 PM
02-26-2014
01:24 PM
Hi Kenny, The FlexFlash was red and not orange (or green) ; the button "Configured Operational Profile" was off It was impossible to access to SCU. I had to do a "reset configuration" : in order to have an access to "the button "Configured Operational Profile" and switch to status orange after that, i could reboot the UCS to SCU and use Sync as you specified. This white paper is very interesing to start with SD card but it miss this piece of information. http://www.cisco.com/c/dam/en/us/solutions/collateral/data-center-virtualization/unified-computing/whitepaper_C11-718938.pdf Thank for your reply and all others ones in past ! Best regards. Nicolas.
... View more
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
02-25-2014
07:07 AM
02-25-2014
07:07 AM
I add a piece of information : The raid controler is a PCIe raid card LSI MegaRAID SAS 9271-8i
... View more
Created by
delahais
in Unified Computing System Discussions
in Unified Computing System Discussions
02-25-2014
06:13 AM
02-25-2014
06:13 AM
Hi, I just start a new C220M3 with 2 SD cards. Right now, i can not use the SD card because i have the following status : "SD Cards are not RAID-1 paired" I do want to use the SD card in RAID-1 in order to install ESXi. The CIMC version is 1.5(3d) Please help. Thanks.
... View more
Labels:
05-07-2014
Hi, Recently under VIF paths tab, on 3 different UCS domains, I did
noticed that some virtual circui...
04-18-2014
The zoning was ko, so the B200M3 did not see any LUN (no local disk)Many
thankNicolas. PS : previous...
Created by
delahais
in Unified Computing System Discussions
04-17-2014
04-17-2014
I just created and associated a new SP to a B200M3.When i check the boot
server via the vConsole, i ...
04-15-2014
Hi,What is the board controller ? what it do ?I have to upgrade a UCS
domain with 12 B200M3 to UCSM ...
Created by
delahais
in Other Data Center Subjects
03-31-2014
03-31-2014
Hi,We have a fabric composed by 2 Nexus 6004. The links between the 2 Nx
6004 are configured with vE...
03-09-2014
Hello Kenny,My main question is « how to use and to configure failover
on VIC 1225 ». I have already...
Created by
delahais
in Unified Computing System Discussions
03-07-2014
03-07-2014
Hi,I have a C240M3 with a VIC 1225. I would want to enable failover.In
order that, i have to enable ...
03-06-2014
Hi Richard, Hi Wdey,First of all thks for your repliesWho is right ???I
am used to use npv/npiv with...
03-05-2014
hi guys,Is-it possible to configure a storage vdc in npv mode ?We "just"
want to consolidate access ...
03-05-2014
hi guys,Is-it possible to configure a storage vdc in npv mode ?We "just"
want to consolidate access ...
Created by
delahais
in Unified Computing System Discussions
02-26-2014
02-26-2014
Hi Kenny,The FlexFlash was red and not orange (or green) ; the button
"Configured Operational Profil...
Created by
delahais
in Unified Computing System Discussions
02-25-2014
02-25-2014
I add a piece of information :The raid controler is a PCIe raid card LSI
MegaRAID SAS 9271-8i
Created by
delahais
in Unified Computing System Discussions
02-25-2014
02-25-2014
Hi,I just start a new C220M3 with 2 SD cards. Right now, i can not use
the SD card because i have th...
Public Statistics
| Date Registered | 02-18-2003 01:24 AM |
| Date Last Visited | 04-09-2018 06:29 AM |
| Total Messages Posted | 137 |
| Total Helpful Votes Received | 5 |
Helpful Votes Given To
