Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Pavlo Zabudskyi
Stats
Member since
09-20-2012
20
Posts
10
Helpful
0
Solutions
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
01-31-2017
01:07 AM
01-31-2017
01:07 AM
It was interface bind related problem.
Asterisk is in private network and VoIP provider in public. So solution was to use global bind interface to interface in private network and dial-peer based bind interface to public interface.
... View more
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
01-27-2017
02:51 AM
01-27-2017
02:51 AM
Phones are registered at CUCM. Asterisk is used for trunks.
New branch is added with cisco 2811 ( c2800nm-adventerprisek9-mz.151-4.M12a.bin)
I guess problem is in Asterisk - CCM express communication. I try to make outbound call to 994125555555, called number is then translated to 5 555555.
cisco 2811 configuration (internal interface 10.10.100.50, external 1.1.1.2) Asterisk - 10.10.10.10 VoIP provider - 1.1.1.1
voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip h323 sip dial-peer voice 1 voip translation-profile outgoing TO-PSTN destination-pattern 994.T session protocol sipv2 session target ipv4:1.1.1.1:4546 session transport udp dtmf-relay rtp-nte codec g711ulaw no vad ! dial-peer voice 102 voip description -= LOCAL GROUP =- answer-address 121234567 destination-pattern 121234567 session protocol sipv2 session target ipv4:10.10.10.10:5060 session transport udp incoming called-number 121234567 dtmf-relay rtp-nte codec g711ulaw no vad
Asterisk (FreePBX) trunk configuration
Peer details type=peer qualify=yes port=5060 nat=no insecure=very host=10.10.100.50 context=from-internal canreinvite=yes allow=alaw&ulaw User details type=user qualify=yes port=5060 nat=no insecure=very host=10.10.100.50 context=from-internal canreinvite=yes allow=alaw&ulaw
Logs are in attechments
... View more
- Tags:
- ccm express
Labels:
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
08-16-2016
03:54 AM
08-16-2016
03:54 AM
I had no luck to collect CUCM logs with RTMT.
Wireshark logs are in attachment.
Warning: 399 cucm-pub "Devicename and instanceID parameter missing for Cisco or preferred vendor device"
... View more
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
08-08-2016
05:40 AM
08-08-2016
05:40 AM
I don't use 7912 device model, I use third party SIP (basic) model.
... View more
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
08-08-2016
05:21 AM
08-08-2016
05:21 AM
CUCM 11.5 doesn't support 7912 IP Phones any more.
I uploaded sip firmware and set SIP settings at phone web interface (ip_addr/dev)
UID phone_number PWD ***** (digest user password) Proxy IP_CUCM UseLoginID 1 LoginID adilm (digest user)
But have no luck. What can be wrong?
... View more
- Tags:
- 7912 cucm11.5
Labels:
06-25-2016
05:58 AM
We had internet connectivity problem. After it was resolved, we wasn't able to connect to VPN with anyconnect client with error "Failed to get AAA hendle"
We updated ios from asa917-k8.bin to asa917-6-k8.bin. No luck. It allows to conect only once after reboot. Very strange behavior. Do we have to change IOS version?
We tried both with local and ldap authentification.
... View more
- Tags:
- anyconnect asa
Labels:
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
12-23-2015
02:27 AM
12-23-2015
02:27 AM
There are registered a lot of devices with both Publisher and Subscriber: 79XX phones, CIPC, Cisco jabber, 3rd party SIP phones, etc.
There are device packs on both servers with latest firmware for 7861.
... View more
12-22-2015
07:58 AM
Hi,
tftp restart and phone reset don't resolve problem. The problem is: Phone can't register with Publisher (first in CM group) and registers with Subscriber. Then phone detects that Publisher is online and try to register with it. But it fails and registers with Subscriber and so on.
What can I see in capture? I don't want to post it in Internet. Can I send it to your e-mail?
... View more
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
in IP Telephony and Phones
12-21-2015
08:43 AM
12-21-2015
08:43 AM
IP phone 7861 (sip78xx.11-0-1-11) registers on CUCM 8.6.2 and after some time unregisters. Then registers again and so on.
Logs say someting like that
2651 NOT Dec 21 18:20:10.981122 JAVA-Thread-6|JPlatUi:setUnregReason - old-unregister-reason:107, new unregister-reason:24, cc-server-type:0
2652 NOT Dec 21 18:20:10.981672 JAVA-Thread-6|JPlatUi:isThisFailureFromNewCause - old unregReason =107 newUnregReason=24
2653 NOT Dec 21 18:20:10.990600 JAVA-Thread-6|JPlatUi:setUnregReason - set to unregister-reason:24
2654 NOT Dec 21 18:20:11.111551 dgetserver(3908)-dgetserver.RESULT [_0_ [PASS] No error
]
2655 NOT Dec 21 18:20:11.136692 downd-SOCKET accept errno=4 "Interrupted system call"
2656 NOT Dec 21 18:20:11.265518 JAVA-Thread-6|cip.sipcc.SipEnhancedAlarmInfo:setLastDeregistrationReason - new unreg-reason=24(LastTimePhoneRegRej), old unreg-reason=107
and that
Time zone data download failed
What can I do to solve this problem?
... View more
- Tags:
- cucm
Labels:
01-17-2014
02:04 AM
I have two sims. profile 1 for slot 0 profile 2 for slot 1 But sim in slot 1 is registering with profile 1 and after 1 hour cellular 0 gsm sim activate slot 1 controller Cellular 0 gsm sim profile 2 ims 1 slot 1 gsm failovertimer 7 sh cellular 0 profile Profile 1 = ACTIVE ** -------- PDP Type = IPv4 PDP address = 10.154.38.157 Access Point Name (APN) = www.kyivstar.net Authentication = None Username: Password: Primary DNS address = 193.41.63.161 Secondary DNS address = 193.41.63.162 Profile 2 = INACTIVE* -------- PDP Type = IPv4 Access Point Name (APN) = www.kyivstar.net Authentication = None Username: Password: Profile 3 = INACTIVE -------- PDP Type = IPv4 Access Point Name (APN) = 3g.utel.ua Authentication = None Username: Password: * - Default profile Configured default profile for active SIM 1 is profile 2. Jan 17 08:56:43.895: TTY0: pause timer type 1 (OK) Jan 17 08:56:43.895: To Activate SIM powering off the modem Jan 17 08:56:44.611: [Cellular0]:CALLCTRL RX Link Status Indication (218 bytes): 00 DA 78 00 01 01 00 D6 03 16 00 55 00 41 00 2D 00 4B 00 59 00 49 00 56 00 53 00 54 00 41 00 52 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4C 49 4E 4B 20 44 4F 57 4E 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ED 00 ED 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Jan 17 08:56:44.615: Incoming LSI msg: profile_id = 1, session_state = 0, pdp_c0 Jan 17 08:56:44.615: TTY3: Async Int reset: Dropping DTR Jan 17 08:56:44.615: ip address for profile id 1 8AAC3890: 000000 0000 Jan 17 08:56:44.615: Cellular0 DirectIP: Remove negotiated IP interface address Jan 17 08:56:44.619: Cellular0 DirectIP: Primary DNS address 193.41.63.161 remod Jan 17 08:56:44.619: Cellular0 DirectIP: Secondary DNS 193.41.63.162 removed Jan 17 08:56:45.543: TTY3: DSR was dropped Jan 17 08:56:45.543: tty3: Modem: READY->(unknown) Jan 17 08:56:46.543: TTY3: dropping DTR, hanging up Jan 17 08:56:46.543: tty3: Modem: HANGUP->(unknown) Jan 17 08:56:46.615: %LINK-5-CHANGED: Interface Cellular0, changed state to rest Jan 17 08:56:47.543: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:47.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0,n Jan 17 08:56:48.543: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:49.491: Setting Active SIM to 1 Jan 17 08:56:49.491: To Activate SIM powering ON the modem Jan 17 08:56:49.491: %CISCO800-6-SIM_ACTIVATION: SIM in slot 1 is being activat. Jan 17 08:56:50.491: Started ACQ TIMER since activate SIM Jan 17 08:56:50.491: TTY0: resume timer type 1 (OK) Jan 17 08:56:50.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:50.503: %CISCO800-2-MODEM_DOWN: Cellular0 modem is now DOWN. Jan 17 08:56:51.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:52.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:53.471: TTY3: Async Int reset: Dropping DTR Jan 17 08:56:53.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:54.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:55.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:56.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:57.503: TTY3: cleanup pending. Delaying DTR Jan 17 08:56:58.471: TTY3: no timer type 0 to destroy Jan 17 08:56:58.471: TTY3: no timer type 1 to destroy Jan 17 08:56:58.471: TTY3: no timer type 3 to destroy Jan 17 08:56:58.471: TTY3: no timer type 4 to destroy Jan 17 08:56:58.471: TTY3: no timer type 10 to destroy Jan 17 08:56:58.471: TTY3: no timer type 2 to destroy Jan 17 08:56:58.471: Cellular0: allowing modem_process to continue hangup Jan 17 08:56:58.471: Started ACQ Timer since Service is Not Normal for act_sim 1 alt_sim 0 Jan 17 08:56:58.471: Sending default profile to 2 active_sim 1 Jan 17 08:56:58.523: TTY3: restoring DTR Jan 17 08:56:58.523: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel1, cn Jan 17 08:56:58.587: Received CNS_GSM_SYSTEM_STATUS: status=1 Jan 17 08:56:58.627: Received CNS_GSM_RETURN_SIM_STATUS: status=0 Jan 17 08:56:58.763: %CISCO800-2-MODEM_UP: Cellular0 modem is now UP. sf.tb29#[Cellular0]:CALLCTRL TX MDM Data Link Sync Indication[Cellular0]:CALLCTn Jan 17 08:56:58.827: Received CNS_GSM_SYSTEM_STATUS: status=1 Jan 17 08:56:59.071: Received CNS_GSM_SYSTEM_STATUS: status=1 Jan 17 08:56:59.091: Received CNS_GSM_SYSTEM_STATUS: status=1 Jan 17 08:56:59.111: Received CNS_GSM_SYSTEM_STATUS: status=1 Jan 17 08:56:59.123: Received CNS_GSM_RETURN_SIM_STATUS: status=0 Jan 17 08:56:59.143: Received CNS_GSM_SYSTEM_STATUS: status=1 Jan 17 08:56:59.163: Received CNS_GSM_SYSTEM_STATUS: status=0 Jan 17 08:56:59.163: Recv CW_SERVICE_STATUS_NORMAL so stopping Acquisition Timer Jan 17 08:56:59.195: Received CNS_GSM_SYSTEM_STATUS: status=0 Jan 17 08:56:59.591: [Cellular0]:CALLCTRL RX Restart Indication (84 bytes): 00 54 62 00 54 31 5F 30 5F 33 5F 32 41 50 20 52 33 36 31 20 43 4E 53 5A 58 44 30 30 30 30 30 30 36 31 20 32 30 31 31 2F 30 34 2F 31 35 20 31 37 3A 34 30 3A 34 38 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Jan 17 08:56:59.603: DIP interface Cellular0 is up! Jan 17 08:57:00.475: %LINK-3-UPDOWN: Interface Cellular0, changed state to down Jan 17 08:57:01.615: Ce0 DDR: re-enable timeout Jan 17 08:57:03.319: Received CNS_GSM_SYSTEM_STATUS: status=0 Jan 17 08:57:08.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel1, cp Jan 17 08:57:10.959: CHAT3: Asserting DTR Jan 17 08:57:10.959: CHAT3: Sending string: at+cimi Jan 17 08:57:10.975: Received CNS_GSM_RETURN_SIM_STATUS: status=0 .Jan 17 09:03:59.609: TTY8: timer type 1 expired .Jan 17 09:03:59.609: TTY8: Error setting disconnect cause .Jan 17 09:03:59.609: TTY8: Exec-timeout expired .Jan 17 09:03:59.609: TTY8: destroy timer type 1 .Jan 17 09:03:59.609: TTY9: timer type 1 expired .Jan 17 09:03:59.609: TTY9: Error setting disconnect cause .Jan 17 09:03:59.609: TTY9: Exec-timeout expired .Jan 17 09:03:59.609: TTY9: destroy timer type 1 .Jan 17 09:03:59.609: TTY10: timer type 1 expired .Jan 17 09:03:59.609: TTY10: Error setting disconnect cause .Jan 17 09:03:59.609: TTY10: Exec-timeout expired .Jan 17 09:03:59.609: TTY10: destroy timer type 1 .Jan 17 09:03:59.609: TTY11: timer type 1 expired .Jan 17 09:03:59.609: TTY11: Error setting disconnect cause .Jan 17 09:03:59.609: TTY11: Exec-timeout expired .Jan 17 09:03:59.609: TTY11: destroy timer type 1 .Jan 17 09:03:59.609: TTY12: timer type 1 expired .Jan 17 09:03:59.609: TTY12: Error setting disconnect cause .Jan 17 09:03:59.609: TTY12: Exec-timeout expired .Jan 17 09:03:59.609: TTY12: destroy timer type 1 ...................................................... .Jan 17 09:53:54.394: Ce0 DDR: place call .Jan 17 09:53:54.394: Ce0 DDR: Dialing cause ip (s=10.0.248.186, d=10.0.248.185) .Jan 17 09:53:54.394: Ce0 DDR: Attempting to dial hspa-R7 .Jan 17 09:53:54.394: CHAT3: Attempting async line dialer script .Jan 17 09:53:54.394: CHAT3: Dialing using Modem script: hspa-R7 & System scripe .Jan 17 09:53:54.394: CHAT3: process started .Jan 17 09:53:54.394: CHAT3: Asserting DTR .Jan 17 09:53:54.394: CHAT3: Chat script hspa-R7 started .Jan 17 09:53:54.394: CHAT3: Sending string: AT!SCACT=1,1 .Jan 17 09:53:54.394: CHAT3: Expecting string: OK .Jan 17 09:53:55.242: Received CNS_GSM_SYSTEM_STATUS: status=0 .Jan 17 09:53:55.262: [Cellular0]:CALLCTRL RX Link Status Indication (218 bytes: 00 DA 78 00 01 01 00 D6 03 16 00 55 00 41 00 2D 00 4B 00 59 00 49 00 56 00 53 00 54 00 41 00 52 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 4C 49 4E 4B 20 55 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 0A 9A 26 9D 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 C1 29 3F A1 00 00 00 00 00 00 00 00 00 00 00 00 04 C1 29 3F A2 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ED 00 ED 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 .Jan 17 09:53:55.266: Incoming LSI msg: profile_id = 1, session_state = 4, pdp_0 .Jan 17 09:53:55.266: ip address for profile id 1 8AAC3890: 0A9A26 9D00 .Jan 17 09:53:55.270: Cellular0 DirectIP: Primary DNS address 193.41.63.161 addd .Jan 17 09:53:55.270: Cellular0 DirectIP: Secondary DNS 193.41.63.162 added .Jan 17 09:53:55.270: CHAT3: Completed match for expect: OK .Jan 17 09:53:55.270: CHAT3: Chat script hspa-R7 finished, status = Success .Jan 17 09:53:55.270: TTY3: no timer type 1 to destroy .Jan 17 09:53:55.270: TTY3: no timer type 0 to destroy .Jan 17 09:53:55.270: TTY3: no timer type 2 to destroy .Jan 17 09:53:57.270: %LINK-3-UPDOWN: Interface Cellular0, changed state to up .Jan 17 09:53:57.270: Ce0 DDR: Dialer statechange to up .Jan 17 09:53:57.270: Ce0 DDR: Dialer call has been placed .Jan 17 09:53:57.270: Cellular0 DirectIP: Install negotiated IP interface addre7 .Jan 17 09:53:57.270: Ce0 DDR: dialer protocol up .Jan 17 09:53:58.270: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0p .Jan 17 09:54:04.394: DDR: IP Address is (10.154.38.157) for (Ce0) .Jan 17 09:54:04.394: DDR: IP Address is (10.154.38.157) for (Ce0)
... View more
- Tags:
- dual-sim
Labels:
12-13-2013
04:51 AM
nat (inside,outside) source dynamic obj-192.168.2.0 obj-192.168.32.20 destination static obj-10.1.56.0 obj-10.1.56.0 It seems that rule doesn't match packet-tracer input inside tcp 192.168.2.1 342 10.1.56.1 34 Phase: 1 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 2 Type: ACCESS-LIST Subtype: log Result: ALLOW Config: access-group test in interface inside access-list test extended permit ip any any Additional Information: Phase: 3 Type: NAT Subtype: per-session Result: ALLOW Config: Additional Information: Phase: 4 Type: IP-OPTIONS Subtype: Result: ALLOW Config: Additional Information: Phase: 5 Type: NAT Subtype: per-session Result: ALLOW Config: Additional Information: Phase: 6 Type: IP-OPTIONS Subtype: Result: ALLOW Config: Additional Information: Phase: 7 Type: FLOW-CREATION Subtype: Result: ALLOW Config: Additional Information: New flow created with id 157, packet dispatched to next module Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: allow My configuration: object network obj-10.1.56.0 subnet 10.1.56.0 255.255.255.0 object network obj-192.168.2.0 host 192.168.2.0 object network obj-192.168.32.20 host 192.168.32.20 interface GigabitEthernet0/0 nameif outside security-level 60 ip address 10.1.255.2 255.255.255.248 standby 10.1.255.3 ! interface GigabitEthernet0/1.2 vlan 2 nameif inside security-level 100 ip address 192.168.2.20 255.255.255.0 standby 192.168.2.254 C 192.168.2.0 255.255.255.0 is directly connected, inside S* 0.0.0.0 0.0.0.0 [1/0] via 10.1.255.1, outside
... View more
Labels:
Created by
Pavlo Zabudskyi
in VPN and AnyConnect
in VPN and AnyConnect
11-20-2013
12:57 AM
11-20-2013
12:57 AM
Yeap it was limitation of standalone one. I upgraded ASDM and created profile with it webvpn svc profiles AnyConnect_profile_allow_RU disk0:/anyconnect_profile_allow_ru.xml group-policy anyconnect attributes webvpn svc profiles value AnyConnect_profile_allow_RU more disk0:/anyconnect_profile_allow_ru.xml AllowRemoteUsers But wasn't able to connect to VPN with RDP connection. I have ASA Version 8.2(1), but there is no record about ASA version limitation. AnyConnect version is anyconnect-win-3.1.04072-k9.pkg
... View more
Created by
Pavlo Zabudskyi
in VPN and AnyConnect
in VPN and AnyConnect
11-20-2013
12:00 AM
11-20-2013
12:00 AM
I can't find Windows VPN Establishment with "Allow Remote Users" in Profile editor. Is it deprecated?
... View more
Labels:
08-02-2013
03:31 AM
Hello, I have two questions, maybe somobody knows answers. 1. Is it possible to change email text which is generated when user is created and OTP is sent. 2. Is it possible to clear certificates in ASDM Configuration->Remote Access VPN->Certificate Management->Local Certificate Authority->Manage User Certificatest in CLI sh crypto CA server cert-db
... View more
Labels:
01-31-2017
It was interface bind related problem. Asterisk is in private network
and VoIP provider in public. S...
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
01-27-2017
01-27-2017
Phones are registered at CUCM. Asterisk is used for trunks. New branch
is added with cisco 2811 (c28...
08-16-2016
I had no luck to collect CUCM logs with RTMT. Wireshark logs are in
attachment. Warning: 399 cucm-pu...
Created by
Pavlo Zabudskyi
in IP Telephony and Phones
08-08-2016
08-08-2016
CUCM 11.5 doesn't support 7912 IP Phones any more. I uploaded sip
firmware and set SIP settings at p...
06-25-2016
We had internet connectivity problem. After it was resolved, we wasn't
able to connect to VPN with a...
12-23-2015
There are registered a lot of devices with both Publisher and
Subscriber: 79XX phones, CIPC, Cisco j...
12-22-2015
Hi, tftp restart and phone reset don't resolve problem. The problem is:
Phone can't register with Pu...
12-21-2015
IP phone 7861 (sip78xx.11-0-1-11) registers on CUCM 8.6.2 and after some
time unregisters. Then regi...
01-17-2014
I have two sims.profile 1 for slot 0 profile 2 for slot 1But sim in slot
1 is registering with profi...
12-13-2013
nat (inside,outside) source dynamic obj-192.168.2.0 obj-192.168.32.20
destination static obj-10.1.56...
11-20-2013
Yeap it was limitation of standalone one.I upgraded ASDM and created
profile with it webvpn svc prof...
11-20-2013
I can't find Windows VPN Establishment with "Allow Remote Users" in
Profile editor. Is it deprecated...
Created by
Pavlo Zabudskyi
in Unified Communications Infrastructure
08-05-2013
08-05-2013
Hello, I have CME (version 7.1) and Grandstream GXP1160Calls, transfer
works.I call from outsidevoic...
Public Statistics
| Date Registered | 09-20-2012 02:18 AM |
| Date Last Visited | 08-18-2017 04:00 AM |
| Total Messages Posted | 20 |
| Total Helpful Votes Received | 10 |
