Basically yes minus the span tree priority 0. We have one switch set for all vlans as root. Which is in my plans to fix. Ive only been on this network for a year and have a lot of work left to get it where it needs to be. Sent from Cisco Technical Support Android App ... View more

No it wasn't the case when I did the test this is what I did: 1. I enabled Vlan 401 2. I tried to ping 10.254.17.1 which was unsuccessful. 3. I set int vlan 1 to shutdown and no ip address 4. I changed default gateway from 10.139.1.1 to 10.254.17.1 5. I tried to ping 10.254.17.1 which was unsuccessful. 6. I then took a capture of the show commands indicating the pruning of vlan 401 on the 4507. 7. Once all was completed I tested the ip route 0.0.0.0 0.0.0.0 10.254.17.1 which was again unsuccessful. Finally, I set everything back to vlan 1 and shutdown vlan 401. Thank you, Anthony ... View more

Here are the show commands you asked for. ... View more

Still unable to get it working even with int vlan 1 disabled. I was checking the trunk ports and ran into something interesting maybe you all might know something about. RCD-MDF-4507#sh int trunk | in Port |Gi1/6 Port        Mode             Encapsulation  Status        Native vlan Gi1/6       on               802.1q         trunking      1 Port        Vlans allowed on trunk Gi1/6       1,17,117,204,401 Port        Vlans allowed and active in management domain Gi1/6       1,17,117,204,401 Port        Vlans in spanning tree forwarding state and not pruned Gi1/6       1,17,117,204 RCD-MDF-4507#sh sp vlan 401 VLAN0401   Spanning tree enabled protocol ieee   Root ID    Priority    8192              Address     0007.b371.11d1              Cost        8              Port        1 (GigabitEthernet1/1)              Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec   Bridge ID  Priority    33169  (priority 32768 sys-id-ext 401)              Address     0025.450e.9ec0              Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec              Aging Time  300 sec Interface           Role Sts Cost      Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/1               Root FWD 8         128.1    P2p Gi1/2               Desg FWD 4         128.2    P2p Gi1/4               Desg FWD 4         128.4    P2p Gi1/5               Desg FWD 4         128.5    P2p Gi1/6               Desg FWD 4         128.6    P2p Gi1/7               Desg FWD 4         128.7    P2p Gi1/8               Desg FWD 4         128.8    P2p Gi1/12              Desg FWD 4         128.12   P2p RCD-MDF-4507# The 4507 says it is pruning this vlan on the port in the sh int trunks but the sh vlan 401 shows it is forwarding on the port. I am now confused as there is no pruning enabled. Just to try I configured Gi1/6 to allow 1,17,117,202, and 401 and still no luck. Here is the same reports from the 3750. RGS-MDF-3750-1-1#show int trunk Port        Mode         Encapsulation  Status        Native vlan Gi1/0/1     on           802.1q         trunking      1 Gi1/0/2     on           802.1q         trunking      1 Gi1/0/3     on           802.1q         trunking      1 Gi1/0/4     on           802.1q         trunking      1 Gi1/0/5     on           802.1q         trunking      1 Gi1/0/6     on           802.1q         trunking      1 Gi1/0/7     on           802.1q         trunking      1 Gi1/0/8     on           802.1q         trunking      1 Gi1/0/12    on           802.1q         trunking      1 Port        Vlans allowed on trunk Gi1/0/1     1-4094 Gi1/0/2     1-4094 Gi1/0/3     1-4094 Gi1/0/4     1-4094 Gi1/0/5     1-4094 Gi1/0/6     1-4094 Gi1/0/7     1-4094 Gi1/0/8     1-4094 Gi1/0/12    1-4094 Port        Vlans allowed and active in management domain Gi1/0/1     1,17,117,204,401 Gi1/0/2     1,17,117,204,401 Gi1/0/3     1,17,117,204,401 Gi1/0/4     1,17,117,204,401 Gi1/0/5     1,17,117,204,401 Gi1/0/6     1,17,117,204,401 Gi1/0/7     1,17,117,204,401 Gi1/0/8     1,17,117,204,401 Gi1/0/12    1,17,117,204,401 Port        Vlans in spanning tree forwarding state and not pruned Gi1/0/1     1,17,117,204,401 Gi1/0/2     1,17,117,204,401 Gi1/0/3     1,17,117,204,401 Gi1/0/4     1,17,117,204,401 Gi1/0/5     1,17,117,204,401 Gi1/0/6     1,17,117,204,401 Gi1/0/7     1,17,117,204,401 Gi1/0/8     1,17,117,204,401 Gi1/0/12    1,17,117,204,401 RGS-MDF-3750-1-1#sh sp vlan 401 VLAN0401   Spanning tree enabled protocol ieee   Root ID    Priority    8192              Address     0007.b371.11d1              Cost        12              Port        12 (GigabitEthernet1/0/12)              Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec   Bridge ID  Priority    33169  (priority 32768 sys-id-ext 401)              Address     001b.9035.3e80              Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec              Aging Time 300 Interface        Role Sts Cost      Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Gi1/0/1          Desg FWD 4         128.1    P2p Gi1/0/2          Desg FWD 4         128.2    P2p Gi1/0/3          Desg FWD 4         128.3    P2p Gi1/0/4          Desg FWD 4         128.4    P2p Gi1/0/5          Desg FWD 4         128.5    P2p Gi1/0/6          Desg FWD 4         128.6    P2p Gi1/0/7          Desg FWD 4         128.7    P2p Interface        Role Sts Cost      Prio.Nbr Type ---------------- ---- --- --------- -------- -------------------------------- Gi1/0/8          Desg FWD 4         128.8    P2p Gi1/0/12         Root FWD 4         128.12   P2p RGS-MDF-3750-1-1# ... View more

I would check the config and see if you have an old TFTP server configured within. I am not familar with the ASR 1001 but I have ran into this issue with other equipment where someone prior programmed the ip to the tftp server into the switch. ... View more

I haven't had a chance to call TAC yet because of some other things that have popped up. However, for some odd reason the 3750 can now ping the 4507 with no changes made to any devices. I will test the setting up of the new MGMT Vlan at 3:30PM CST and see if I can get it up and working. The question I have now is why would I have to have ip routing enabled on the 3750 when the only thing I am trying to setup is a management Vlan? I should only have to set the vlan 401 to the desired IP address and set a default gateway correct? This is all I did on the other network segments and they are working correctly. ... View more

I just removed all of int vlan 401 from the switch and I still cannot ping the 10.254.17.1. I figured this was an easy fix but since it's Monday and I think it has something to do with the 4507 I am going to go ahead and call TAC on this one. I appreicate everyone's help and if you want to still provide suggestions until I can get TAC on the line I am willing to keep trying and if not if TAC figures out the issue I will post the steps we took to fix the problem. Thank you all again for the assistance. ... View more

WISD-6509-Router>traceroute 10.254.17.1 Type escape sequence to abort. Tracing the route to 10.254.17.1   1 10.200.1.18 4 msec     10.139.4.1 0 msec * WISD-6509-Router>show ip route Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP        D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area        N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2        E1 - OSPF external type 1, E2 - OSPF external type 2        i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2        ia - IS-IS inter area, * - candidate default, U - per-user static route        o - ODR, P - periodic downloaded static route Gateway of last resort is 10.140.2.50 to network 0.0.0.0      10.0.0.0/8 is variably subnetted, 65 subnets, 3 masks C       10.136.0.0/16 is directly connected, Vlan136 C       10.138.0.0/16 is directly connected, Vlan138 C       10.139.0.0/16 is directly connected, Vlan1 C       10.200.1.16/29 is directly connected, Vlan303 D       10.254.32.0/20 [90/3072] via 10.200.1.2, 1d19h, Vlan301                        [90/3072] via 10.139.6.100, 1d19h, Vlan1 C       10.254.0.0/20 is directly connected, Vlan400 D       10.254.48.0/20 [90/3072] via 10.200.1.58, 1d19h, Vlan308                        [90/3072] via 10.139.18.1, 1d19h, Vlan1 D       10.254.16.0/20 [90/3072] via 10.200.1.18, 1d19h, Vlan303                        [90/3072] via 10.139.4.1, 1d19h, Vlan1 S*   0.0.0.0/0 [1/0] via 10.140.2.50 WISD-6509-Router> ... View more

I have disabled the int vlan 401 on the 3750 because it is not working. I still have the old mgmt vlan enabled and working vlan 1. However, even with 401 disabled I should still be able to ping 10.254.17.1 because vlan 1 is enabled with a default route to a l3 switch that can reach 10.254.17.1. If I am wrong please correct me. I am trying to solve the problem of not being able to ping 10.254.17.1 which is enabled and working on the 4507. Rick, Even when I do a no shut on that interface it doesn't work. I cannot reach the switch through vlan 401. Thank you for any help and if I need to post more reports please let me know. ... View more

RGS-MDF-3750-1-1#show ip route Default gateway is 10.139.1.1 Host               Gateway           Last Use    Total Uses  Interface ICMP redirect cache is empty RGS-MDF-3750-1-1#show ip interface brief Interface              IP-Address      OK? Method Status                Protocol Vlan1                  10.139.17.1     YES manual up                    up Vlan401                10.254.20.1     YES NVRAM  administratively down down GigabitEthernet1/0/1   unassigned      YES unset  up                    up GigabitEthernet1/0/2   unassigned      YES unset  up                    up GigabitEthernet1/0/3   unassigned      YES unset  up                    up GigabitEthernet1/0/4   unassigned      YES unset  up                    up GigabitEthernet1/0/5   unassigned      YES unset  up                    up GigabitEthernet1/0/6   unassigned      YES unset  up                    up GigabitEthernet1/0/7   unassigned      YES unset  up                    up GigabitEthernet1/0/8   unassigned      YES unset  up                    up GigabitEthernet1/0/9   unassigned      YES unset  down                  down GigabitEthernet1/0/10  unassigned      YES unset  down                  down GigabitEthernet1/0/11  unassigned      YES unset  down                  down GigabitEthernet1/0/12  unassigned      YES unset  up                    up RGS-MDF-3750-1-1#show interfaces status Port      Name               Status       Vlan       Duplex  Speed Type Gi1/0/1                      connected    trunk      a-full a-1000 1000BaseSX SFP Gi1/0/2                      connected    trunk      a-full a-1000 1000BaseSX SFP Gi1/0/3                      connected    trunk      a-full a-1000 1000BaseSX SFP Gi1/0/4                      connected    trunk      a-full a-1000 1000BaseSX SFP Gi1/0/5                      connected    trunk      a-full a-1000 10/100/1000BaseTX SFP Gi1/0/6                      connected    trunk      a-full a-1000 10/100/1000BaseTX SFP Gi1/0/7                      connected    trunk      a-full a-1000 10/100/1000BaseTX SFP Gi1/0/8                      connected    trunk      a-full a-1000 10/100/1000BaseTX SFP Gi1/0/9                      notconnect   1            auto   auto Not Present Gi1/0/10                     notconnect   1            auto   auto Not Present Gi1/0/11                     notconnect   1            auto   auto Not Present Gi1/0/12                     connected    trunk      a-full a-1000 1000BaseLX SFP RGS-MDF-3750-1-1# ************4507***************** RCD-MDF-4507#sh ip int br Interface              IP-Address      OK? Method Status                Protocol Vlan1                  10.139.4.1      YES NVRAM  up                    up Vlan401                10.254.17.1     YES NVRAM  up                    up FastEthernet1          unassigned      YES NVRAM  down                  down GigabitEthernet1/1     unassigned      YES unset  up                    up GigabitEthernet1/2     unassigned      YES unset  up                    up GigabitEthernet1/3     unassigned      YES unset  down                  down GigabitEthernet1/4     unassigned      YES unset  up                    up GigabitEthernet1/5     unassigned      YES unset  up                    up GigabitEthernet1/6     unassigned      YES unset  up                    up GigabitEthernet1/7     unassigned      YES unset  up                    up GigabitEthernet1/8     unassigned      YES unset  up                    up GigabitEthernet1/9     unassigned      YES unset  down                  down GigabitEthernet1/10    unassigned      YES unset  down                  down GigabitEthernet1/11    unassigned      YES unset  down                  down GigabitEthernet1/12    unassigned      YES unset  up                    up Port      Name                         Status       Vlan       Duplex  Speed Type Gi1/1     #### 6509 Water         connected    trunk        full   1000 1000BaseZX Gi1/2     #### 6509 1378           connected    trunk        full   1000 1000BaseLH Gi1/3     ####  BLDG 1             notconnect   1            full   1000 No Gbic Gi1/4     ####BLDG2####          connected    trunk        full   1000 1000BaseLH Gi1/5     ####BLDG3####          connected    trunk        full   1000 1000BaseLH Gi1/6     ####BLDG4####           connected    trunk        full   1000 1000BaseLH Gi1/7     ####BLDG5####           connected    trunk        full   1000 1000BaseLH Gi1/8     ####BLDG6####           connected    trunk        full   1000 1000BaseLH Gi1/9                                        notconnect   1            full   1000 No Gbic Gi1/10                                      notconnect   1            full   1000 No Gbic Gi1/11                                      notconnect   1            full   1000 No Gbic Gi1/12    ####BLDG7####             connected    trunk        full   1000 1000BaseSX ... View more

RGS-MDF-3750-1-1>ping 10.254.17.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.254.17.1, timeout is 2 seconds: ..... Success rate is 0 percent (0/5) RGS-MDF-3750-1-1#show run int vlan 1 ! interface Vlan1 ip address 10.139.17.1 255.255.0.0 end RGS-MDF-3750-1-1#show run | in ip de ip default-gateway 10.139.1.1 RGS-MDF-3750-1-1#show cdp nei Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge                   S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone Device ID            Local Intrfce         Holdtme   Capability    Platform   Port ID RCD-MDF-4507.wylieisd.net                     Gig 1/0/12            122           R S I     WS-C4507R-Gig 1/6 RGS-MDF-3750-1-1#show run int gi1/0/5 ! interface GigabitEthernet1/0/5 switchport trunk encapsulation dot1q switchport mode trunk srr-queue bandwidth share 10 10 60 20 srr-queue bandwidth shape  10  0  0  0 queue-set 2 mls qos trust cos auto qos voip trust spanning-tree link-type point-to-point end ****************4507****************** RCD-MDF-4507#show run int vlan 401 ! interface Vlan401 ip address 10.254.17.1 255.255.240.0 no ip redirects end RCD-MDF-4507#show run int vlan 1 ! interface Vlan1 ip address 10.139.4.1 255.255.0.0 no ip redirects end RCD-MDF-4507#show run | be eigrp router eigrp 1 network 10.0.0.0 no eigrp log-neighbor-changes ! ip default-gateway 10.139.1.1 no ip forward-protocol udp netbios-ns no ip forward-protocol udp netbios-dgm ip route 0.0.0.0 0.0.0.0 10.139.1.1 ip route 0.0.0.0 0.0.0.0 10.140.2.50 RCD-MDF-4507#sh run int gi1/6 ! interface GigabitEthernet1/6 description ####Smith####                                     switchport mode trunk auto qos voip trust service-policy input AutoQos-VoIP-Input-Cos-Policy service-policy output AutoQos-VoIP-Output-Policy end I know these network is not configured optimally but I am working on it. Once I solve this problem I will be able to shrink my routing tables and expand L3 to each building versus just the 4 areas. So any help with this problem is very much appreciated. I also tried the settings indicated above with taking out the default gateway and setting ip route 0.0.0.0 0.0.0.0 10.254.17.1 but I was still unable to ping 10.254.17.1 or connect to the switch 10.254.20.1. ... View more

I do understand what you are saying here. However, this is a production network with 69 vlans and I have to get the management vlans broken up before I can setup the layer 3 links between L3 switches. I have 3 of the 4 areas already moved to the new management vlan. With that said I am having issues with the last one. I have configured the 4507 and l2 switch as you indicated minus the access port connection to the 6509. The issue is any of the switches directly connected to the 4507 cannot ping the 10.254.17.1 interface on the 4507. I programmed the l2 switches with management interfaces of 10.254.18.1, 10.254.19.1/20, 10.254.20.1/20 and 10.254.21.1/20 on Vlan 401 with default gateway of 10.254.17.1. When doing this I cannot get to the switches or ping the switches from the 4507 or anywhere else in the network. I have not had a chance to try out the ip route on the 3750 l2 switch yet. I will post my findings as I try it in a few hours. Thank you again for any assitance. ... View more

Let me know if this clears anything up. We have eigrp setup between the four layer 3 switches in seperate buildings. Right now 10.139.1.1 is the mgmt ip of our main layer 3 switch. Every other switch all 350+ are currently using vlan 1 all gateways are programmed to 10.139.1.1. I am trying to seperate the mgmt networks with a \20 subnet to setup layer 3 links between the layer 3 switches instead of the truncks currently configured. The other 3 switches have mgmt vlans setup and working fine. The one 4507r-e with dual sup 6e's running ios 12.2 (54) I have setup vlan 401 with 10.254.17.1\20 to be the mgmt vlan for the six buildings connecting to it. I can ping 10.254.17.1 from all other layer 3 switching telling me eigrp is working correctly. However when I program a switch connected to the 4507 for vlan 401 10.254.20.1 or .19.1 with ip default gateway of 10.254.17.1 I cannot communicate with the switch. When I set it back to vlan 1 with 10.139.20.1 and gateway 10.139.1.1 I can ping everything but 10.254.17.1. For some reason the 4507 wont let any layer 2 switches directly connected too it talk with the svi 401. I have made sure no pruning was being done on the trunks to the layer 3 switch. I have had no problems with this configuration on the other 3 layer 3 switches which are 1 6509 wih sup 720b's and 2 4507r's with sup 4s. Let me know if this added confusion or clearified anything. I will test the ip route and see if it works once im on site again. Thank you all for your help. Sent from Cisco Technical Support Android App ... View more