yes Leo. ... View more

Dear Leo, I mean, i had reset the AP and assign static ip address before but still AP still cant associate to wlc. and dont know why, this step is work now. Thanks, Arik ... View more

Hi Sandeep, So, what do you want me to do? to change the timezone on WLC? i cant do that because will impact to network. and with AP, that i know we cant change that, or do you have any idea to change the timezone on AP? Thanks, Arik ... View more

Hi Leo, No firewall, Thxs, Arik ... View more

Hi Scott, Before you said to factory default, i had been reset the AP, yes the hostname is the mac-address, but to make sure i had to reset again and capture it, this is the capture: TEST#Xmodem file system is available. flashfs[0]: 13 files, 4 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 15998976 flashfs[0]: Bytes used: 10060800 flashfs[0]: Bytes available: 5938176 flashfs[0]: flashfs fsck took 39 seconds. Base ethernet MAC Address: 00:1d:45:36:86:ca Initializing ethernet port 0... Reset ethernet port 0... Reset done! link auto-negotiating.... auto-negotiation takes 10000 milli-seconds to complete ERROR: timeout waiting for auto-negotiation to complete ERROR: fail to bring ethernet link up The system has been encountered an error initializing ethernet port. You may need to check hardware The system is ignoring the error and continuing boot. If you interrupt the system boot process, the following commands will reinitialize ethernet, tftp, and finish loading the operating system software:     ether_init     tftp_init     boot button is pressed, wait for button to be released... button pressed for 173 seconds process_config_recovery: set IP address and config to default 10.0.0.1 process_config_recovery: image recovery ap:  delete flash:private-config Are you sure you want to delete "flash:private-config" (y/n)?y File "flash:private-config" not deleted -- no such file or directory ap: delete flash:private-multiple-fs Are you sure you want to delete "flash:private-multiple-fs" (y/n)?y File "flash:private-multiple-fs" deleted ap: ap: boot Loading "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx"...################################################################################################################################################################################################## File "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000 executing...               Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.            cisco Systems, Inc.            170 West Tasman Drive            San Jose, California 95134-1706 Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 30-Oct-08 12:05 by prod_rel_team Image text-base: 0x00003000, data-base: 0x003C24A0 Initializing flashfs... flashfs[1]: 12 files, 4 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 15998976 flashfs[1]: Bytes used: 10059776 flashfs[1]: Bytes available: 5939200 flashfs[1]: flashfs fsck took 4 seconds. flashfs[1]: Initialization complete....done Initializing flashfs. This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com . cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory. Processor board ID xxxxxF PowerPCElvis CPU at 262Mhz, revision number 0x0950 Last reset from power-on LWAPP image version 3.0.51.0 1 FastEthernet interface 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:1D:45:36:86:CA Part Number                          : 73-9925-06 PCA Assembly Number                  : 800-26579-05 PCA Revision Number                  : A0 PCB Serial Number                    : xxxx Top Assembly Part Number             : 800-29151-02 Top Assembly Serial Number           : xxxxx Top Revision Number                  : A0 Product/Model Number                 : AIR-LAP1242AG-A-K9  The name for the keys will be: ap.cisco.com % The key modulus size is 1024 bits % Generating 1024 bit RSA keys, keys will be non-exportable...[OK] ip ssh version 2     ^ % Invalid input detected at '^' marker. transport input ssh                  ^ % Invalid input detected at '^' marker. aaa new-model ^ % Invalid input detected at '^' marker. aaa authentication login default enable local none ^ % Invalid input detected at '^' marker. o ^ % Invalid input detected at '^' marker. Press RETURN to get started! *Mar  1 00:00:08.205: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up *Mar  1 00:00:09.232: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down *Mar  1 00:00:09.635: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source *Mar  1 00:00:16.375: %SYS-5-RESTART: System restarted -- Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 30-Oct-08 12:05 by prod_rel_team transport input ssh                  ^ % Invalid input detected at '^' marker. logging origin-id string AP:001d.4536.86ca          ^ % Invalid input detected at '^' marker. logging 255.255.255.255         ^ % Invalid input detected at '^' marker. logging trap 3         ^ % Invalid input detected at '^' marker. *Mar  1 00:00:27.393: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY *Mar  1 00:00:27.882: Logging LWAPP message to 255.255.255.255. TEST> Thanks, Arik ... View more

Hi Sandee, This is your request, but without "debug lwapp events enable" because i worry this is will impact to network and user has been connected to network. WLC: (Cisco Controller) >show sysinfo Manufacturer's Name.............................. Cisco Systems Inc. Product Name..................................... Cisco Controller Product Version.................................. 7.0.98.218 RTOS Version..................................... 7.0.98.218 Bootloader Version............................... 4.0.206.0 Emergency Image Version.......................... 5.2.157.0 Build Type....................................... DATA + WPS System Name...................................... IDMAN System Location.................................. Jakarta, Indonesia System Contact................................... Agus Kurniwanto System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3 IP Address....................................... X.X.X.X System Up Time................................... 392 days 8 hrs 36 mins 36 secs System Timezone Location......................... (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar Configured Country............................... US  - United States Operating Environment............................ Commercial (0 to 40 C) Internal Temp Alarm Limits....................... 0 to 65 C Internal Temperature............................. +40 C State of 802.11b Network......................... Enabled --More-- or (q)uit State of 802.11a Network......................... Disabled Number of WLANs.................................. 5 Number of Active Clients......................... 28 Burned-in MAC Address............................ 00:1D:70:20:6C:60 Crypto Accelerator 1............................. Absent Crypto Accelerator 2............................. Absent Power Supply 1................................... Absent Power Supply 2................................... Present, OK Maximum number of APs supported.................. 100 AP: TEST>SH VER Cisco IOS Software, C1240 Software (C1240-RCVK9W8-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by Cisco Systems, Inc. Compiled Thu 30-Oct-08 12:05 by prod_rel_team ROM: Bootstrap program is C1240 boot loader BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1) TEST uptime is 1 minute System returned to ROM by power-on System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com . cisco AIR-LAP1242AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory. Processor board ID FTX1135B3ZF PowerPCElvis CPU at 262Mhz, revision number 0x0950 Last reset from power-on LWAPP image version 3.0.51.0 1 FastEthernet interface 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:1D:45:36:86:CA Part Number                          : 73-9925-06 PCA Assembly Number                  : 800-26579-05 PCA Revision Number                  : A0 PCB Serial Number                    : Fxxxxxxxxx Top Assembly Part Number             : 800-29151-02 Top Assembly Serial Number           : Fxxxxxxxxxx Top Revision Number                  : A0 Product/Model Number                 : AIR-LAP1242AG-A-K9  Configuration register is 0xF Thxs, Arik ... View more

Hi Scott, Still no luck, after i reboot this is messagefrom AP, %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address x.x.x.x, mask 255.255.255.0, hostname TEST Translating "CISCO-LWAPP-CONTROLLER.zzzz.zzzzz.net"...domain server (x.x.x.x) %LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP. %LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP. %LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER. zzzz.zzzzz.net %LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.i zzzz.zzzzz.net %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source TEST#debug lwapp client config LWAPP Client config display debugging is on TEST#debug lwapp client err   TEST#debug lwapp client error LWAPP Client ERROR display debugging is on TEST# TEST# TEST#debug lwapp client ev    TEST#debug lwapp client event LWAPP Client EVENT display debugging is on TEST# TEST#debug lwapp client packet LWAPP Client PACKET display debugging is on TEST# TEST# TEST# *Mar  1 00:04:59.685: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 00:05:09.685: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 00:05:19.685: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 00:05:29.685: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 00:05:39.684: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR Thxs, Arik ... View more

Hai Scott, I had config static ip address for this AP with same vlan with WLC, but still not work, I try debug the AP, this is the message: ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ TEST#debug lwapp client error LWAPP Client ERROR display debugging is on TEST#debug lwapp client eve  TEST#debug lwapp client event LWAPP Client EVENT display debugging is on TEST# TEST#debug lwapp client pack  TEST#debug lwapp client packet LWAPP Client PACKET display debugging is on TEST# TEST# TEST# TEST# *Mar  1 01:45:24.237: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 01:45:24.237: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found *Mar  1 01:45:24.237: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to x.x.x.x *Mar  1 01:45:24.237: Sent Msg Type   :   DISCOVERY_REQUEST *Mar  1 01:45:24.237: Msg Length     :   21 debug lwapp client packet SeqNum     :   0 LWAPP Client PACKET display debugging is on TEST# TEST# TEST#debug lwapp client conf   TEST#debug lwapp client config LWAPP Client config display debugging is on TEST# TEST# TEST# *Mar  1 01:45:37.237: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 01:45:37.237: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found *Mar  1 01:45:37.237: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to x.x.x.x *Mar  1 01:45:37.237: Sent Msg Type   :   DISCOVERY_REQUEST *Mar  1 01:45:37.237: Msg Length     :   21 *Mar  1 01:45:37.237: Msg SeqNum     :   0 *Mar  1 01:45:50.237: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 01:45:50.237: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found *Mar  1 01:45:50.237: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to x.x.x.x *Mar  1 01:45:50.237: Sent Msg Type   :   DISCOVERY_REQUEST *Mar  1 01:45:50.237: Msg Length     :   21 *Mar  1 01:45:50.237: Msg SeqNum     :   0 *Mar  1 01:46:03.237: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 01:46:03.237: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found *Mar  1 01:46:03.237: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to x.x.x.x *Mar  1 01:46:03.237: Sent Msg Type   :   DISCOVERY_REQUEST *Mar  1 01:46:03.237: Msg Length     :   21 *Mar  1 01:46:03.237: Msg SeqNum     :   0 *Mar  1 01:46:16.237: LWAPP_CLIENT_EVENT: spamHandleDiscoveryTimer: Could not discover any MWAR *Mar  1 01:46:16.237: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found *Mar  1 01:46:16.237: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found *Mar  1 01:46:16.237: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to x.x.x.x *Mar  1 01:46:16.237: Sent Msg Type   :   DISCOVERY_REQUEST *Mar  1 01:46:16.237: Msg Length     :   21 *Mar  1 01:46:16.237: Msg SeqNum     :   0 with x.x.x.x is the ip address of AP, +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Thanks, Arik ... View more

rasikanayanajith I try your post to assign static ip address, but the result is same, the AP still not discover from WLC. nkumarsr sorry, update, not work... , but before the AP is discover with static ip address sandeepchoudhary21 we use dhcp server with dedicated server, not dhcp from switch or router. Thxs, ... View more

Dear Rasika, I forgot, that before i reset this AP, this AP has detect by WLC but with static IP Address. reason for the reset because AP with different vlan. So, we can say that AP has been detected by WLC before, now, what should i do? should i configure this AP with static IP Address? Thanks, Arik ... View more