Cisco Community
English
Register
Great changes are coming to Cisco Community in July. LEARN MORE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
jkirby
‎08-29-2018

Beginner
Recent Badges
Awards
Recent Badges
See all
1 Helpful Vote
20 Replies
10 Replies
5 Replies
Stats
Member since ‎08-01-2000
33
Posts
9
Helpful
0
Solutions

The problem has been resolved

Created by in Wireless
10-17-2014
10-17-2014
The problem has been resolved. Indeed it was not one but two bad cables. They worked with my laptop ...

Been there, done that.  There

Created by in Wireless
10-17-2014
10-17-2014
Been there, done that. There's nothing in the boot process that shows any failed anything. But I"ll ...

This output is while the SFP

Created by in Wireless
10-17-2014
10-17-2014
This output is while the SFP is inserted and a known good cable plugged into a known good GigE port ...

Yes.  I've tried three GLC-T,

Created by in Wireless
10-15-2014
10-15-2014
Yes. I've tried three GLC-T, all Cisco branded, and get the same result every time. I can plug the s...

How to tell if on board ethernet is failed on a 5508 wireless controller?

Created by in Wireless
10-15-2014
10-15-2014
We have a WLC 5508 that we use for mobility product development and customer demos. When I insert a ...

Re: no "redundancy" command for VSS on 4500 Sup7E w/ IOS-XE 3.4.

Created by in Switching
03-06-2013
03-06-2013
Here it is:Switch#show versionCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software ...

Re: no "redundancy" command for VSS on 4500 Sup7E w/ IOS-XE 3.4.

Created by in Switching
03-06-2013
03-06-2013
Yes, I understand the need for, and mechanismis used by, SSO and NSF. It's just that the required co...

no "redundancy" command for VSS on 4500 Sup7E w/ IOS-XE 3.4.0

Created by in Switching
03-06-2013
03-06-2013
According to the VSS configuration chapter of the IOS-XE 3.4.0 configuration guide, SSO/NSF need to ...

Re: Per-tunnel QoS and physical interface CBWFQ

Created by in Routing
07-19-2012
07-19-2012
Arrgh! Me too! I need to shape per-tunnel traffic at the hubs to prevent overriding any of the spoke...

Re: Can the WSA forward HTTPS to another proxy using routing pol

Created by in Web Security
05-23-2012
05-23-2012
I wish it were that simple. The routing policy and the decrypt policy are triggered on the same cust...

Can the WSA forward HTTPS to another proxy using routing policies?

Created by in Web Security
05-23-2012
05-23-2012
We have an IronPort S160 version 7.1.3-021 for Web configured as a transparent proxy. We need to for...

Netflow in a dual-homed hosting environment

Created by in Network Management
08-03-2011
08-03-2011
Fixed my own problem. I removed the line "ip flow ingress layer2-switched vlan 50" and left the "ip ...

Documentation - Using Router as Netflow Probe

Created by in Routing
07-26-2011
07-26-2011
Sorry to jump on an old thread but after finding libpcap on CentOS dropping too many packets I also ...

Netflow in a dual-homed hosting environment

Created by in Network Management
07-13-2011
07-13-2011
Hello,We're trying to set up netflow based billing for our hosting environment. We're dual homed to ...

Re: IPv6 Interface ID selection

Created by in IPv6
04-11-2011
04-11-2011
Wow, that's exactly the kind of answer I was hoping for. As with many other IPv6 "rules" I've come a...
Public Statistics
Date Registered ‎08-01-2000 06:22 AM
Date Last Visited ‎08-29-2018 12:01 AM
Total Messages Posted 33
Total Helpful Votes Received 9
Helpful Votes Given To
See all >
Helpful Votes From
See all >