About proziumwtf

proziumwtf · 11-28-2024

I am encountering an issue while attempting to replace the bootflash on an ISR 4431/K9 with MEM-FLSH-16G. Specifically, I have observed two distinct types of MEM-FLSH-16G, differentiated by their serial numbers:Units with serial numbers starting with...

proziumwtf · 10-30-2020

I am trying to figure out what is the difference between those 3 SKUs :NCS-5011-32F , NCS-5011-32H and NCS-5011 . The Data Sheets tells me that NCS-5011 has 32 ports that support either 10GE/25GE/40GE/50GE/100GE, but I really cant figure out what the...

proziumwtf · 06-08-2020

Hi I am planning an upgrade from ASR1002 IOS 3.16 to RP3 16.5 ASR1006-X Chassis and ESP-100. I didn't find tho if the LNS/LAC PPPoE configurations are supported . I did find an article about configuring it on the asr1k - > https://www.cisco.com/c/en/...

proziumwtf · 11-04-2019

I have the following hardware : SX20 Codec with firmware TC7.3.6.ea51021. The codec is connected to a CTS-PHD1080P12XS2 camera with a CAB-PHD4XS2-SPLIT cable. I have a TRC5 remote, which has to be compatible with the TC software The problem however i...

proziumwtf · 10-28-2019

I've upgraded 2 of our ASR1000-RP2 ( they are in ASR1004s ) to 16.9.4 IOS XE. The previous version was : 3.13 ( 154-3 ) . Since the upgrade the ASR1000-SIP10 doesn't get recognized . It detects that something is in slot 0 *Oct 28 16:34:33.512: %IOSX...

proziumwtf · 12-11-2024

I attempted to boot the ISR4400 using the firmware isr4400-universalk9.16.09.08.SPA.bin through a USB drive. The process proceeded as expected, and after formatting the eUSB, the correct size was displayed.Additionally, I recently discovered that the...

proziumwtf · 11-16-2023

Is your device N540L or N540X, because if so, you would need a different software image, one can assume, this would be the problem...

proziumwtf · 07-18-2023

Try changing the baud rate while using ISR4451 when starting a session with the module. When logged in the module, you get notified with the available commands despite the different baud rate. Type in the suggested command for setting up the desired ...

proziumwtf · 11-05-2020

The weird thing is that on the label of the box it's written NCS-5011-32F and yet I get 100G speeds according to the show interface command. Also if I search for the device in the Cisco database it comes up as 32F and not 32H . But why would it repor...

proziumwtf · 11-02-2020

I have the 32F version with me and when I connect a port to another 100G port I get 100G speeds : RP/0/RP0/CPU0:ios#show int hu0/0/0/2 Fri Oct 30 13:45:55.302 UTC HundredGigE0/0/0/2 is up, line protocol is up Interface state transitions: 1 Hardwa...

Member Since	‎05-26-2014 12:38 AM
Date Last Visited	‎03-18-2025 02:34 AM
Posts	17

User Statistics

User Activity

I need to replace the bootflash for ISR4431/K9 with MEM-FLSH-16G

What is the difference between NCS-5011-32F , NCS-5011-32H and NCS-5011 ?

ASR1002 3.16 IOS vs ASR1006 RP3 ESP100 16.5 IOS LAC/LNS PPPoE Configuration Differences

Can't control the SX20 Codec via the CTS-PHD1080P12XS2 with TRC5 remote. Need help troubleshooting

ASR1000-SIP10 doesn't get recognized on ASR1000-RP2 with ( 16.9.4 IOS XE )

Re: I need to replace the bootflash for ISR4431/K9 with MEM-FLSH-16G

Re: NCS540 USB boot Problem

Re: CISCO 2951 and 48port EtherSwitch module (baud issues)

Re: What is the difference between NCS-5011-32F , NCS-5011-32H and NCS-5011 ?

Re: What is the difference between NCS-5011-32F , NCS-5011-32H and NCS-5011 ?