About ivanchakarov

ivanchakarov · ‎02-13-2018

Hello! Can I restore an application backup of Cisco Prime Infrastructure 3.1 to a fresh install of 3.2.2? The documentation states that it is impossible to restore an appliance backup but what about the default application backup? https://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/3-2/admin/guide/bk_CiscoPrimeInfastructure_3_2_AdminGuide/bk_CiscoPrimeInfastructure_3_2_AdminGuide_chapter_010.html

ivanchakarov · ‎11-23-2017

Did somebody find the root cause or solution of the problem? I still cannot find related registered bug and I do not want to experiment with 8.5. :|

ivanchakarov · ‎10-18-2017

What about the clients that are using older software - 7.4 for example?

ivanchakarov · ‎08-24-2017

Unfortunately CSCvb44979 is still present in 8.2.160.0 even that it is stated that it is fixed. The command “config local-auth cipher-option 3des-rc4 enable” still has to be used to work around it.

ivanchakarov · ‎07-31-2017

8.2.160.0(ED) is out for some days. :)

ivanchakarov · ‎01-25-2017

Can you show logs from the AP's CLI ? However, I am pretty sure you are hitting this bug - https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvc40470 We are waiting for the next release. :(

ivanchakarov · ‎01-22-2017

And this is the problem. :) The PI support for APs 2800 and 3800 begins in version 3.1.1. Now you can only see the 1532 AP. You have to upgrade Prime, preferably to version 3.1.4

ivanchakarov · ‎01-22-2017

What model are the APs ?

ivanchakarov · ‎01-22-2017

You should disable Data Rates from: Wireless > 802.11xx > Network > Data Rates

ivanchakarov · ‎01-19-2017

Deploy some kind of Network Management System, Cisco Prime Infrastructure for example.

ivanchakarov · ‎01-17-2017

If the elected AP goes down, another will be elected on its place. There will not be any problems.

ivanchakarov · ‎01-17-2017

The traffic is not processed from the "Controller elected AP". It is locally switched by the access point to which the clients are associated. It is similar to the well known FlexConnect Local Switch mode.

ivanchakarov · ‎01-16-2017

You can configure SNMP to send traps about the associations. This information is going to be presented on the WLC's home screen also.

ivanchakarov · ‎01-16-2017

You can turn on a debug to observe the association process. Use the following command: debug client <client MAC addr>

ivanchakarov · ‎01-14-2017

PI support for Cisco 2800/3800 APs is introduced first in patch 3.1 .3 . If you are currently using 3.1 only you have to upgrade the Prime, preferably to 3.1.4.

Date Registered	‎04-09-2014 12:08 AM
Date Last Visited	‎09-18-2018 01:26 AM
Total Messages Posted	27
Total Helpful Votes Received	23

Can I restore PI application backup tak...

Re: Client can't pass traffic at all

Re: WPA2 vulnerability

Re: 8.2.160.0 released: http:/

8.2.160.0(ED) is out for some

Can you show logs from the AP

And this is the problem. :)

What model are the APs ?

You should disable Data Rates

Deploy some kind of Network

If the elected AP goes down,

The traffic is not processed

You can configure SNMP to

You can turn on a debug to

PI support for Cisco 2800