About bhatok

bhatok · 12-24-2013

I am trying to migrate to a Nexus 1000v vDS but only VM's in the system VLAN can forward traffic. I do not want to make my voice vlan a system VLAN but that is the only way I can get a VM in that VLAN to work properly. I have a host with its vmk in t...

bhatok · 10-25-2010

I posted this on the LAN routing & switching board but I figured I'd try it here and maybe get some opinions of some WAN routing people.I have a 4510R-E supervisor 6E with 5 EIGRP neighbors. From the 4510 I do a "show ip eigrp neighbor" and 3 of the ...

bhatok · 10-25-2010

I have a 4510R-E supervisor 6E running IOS 12.2(46)SG. It has 5 EIGRP neighbors. From the 4510 I do a "show ip eigrp neighbor" and 3 of the neighbors show a SRTT of around 500ms and RTO around 3000. When I do a "show ip eigrp neighbor" from each of t...

bhatok · 11-23-2009

I am trying to get a NAC demo running and am having some issues with a Layer 2 OOB, Virtual GW configuration. Currently I have 3560G switches and would like to assign ports to a vlan based on user roles.My Auth VLAN is 110 and maps to VLAN 11Guest VL...

bhatok · 01-09-2009

What format is this file in? I cannot find any examples in the Cisco documentation. I have 25 mac addresses I'd like to add without doing one at a time.Thanks,Brandon

bhatok · 12-30-2013

I ended up failing over to my other VSM and then I did a shutdown / no shutdown on ethernet3/8 and it started working. I am not sure if it was the failover or the shut/no shut that actually did it but everything is working now. Thanks again for helpi...

bhatok · 12-27-2013

Below is the output you requested. Thank you.~ # vemcmd show cardCard UUID type 2: 4c4c4544-004c-5110-804a-b9c04f564831Card name: synergvm5Switch name: synergVSMSwitch alias: DvsPortset-0Switch uuid: 7d e9 0d 50 b3 3b 25 47-64 14 61 c0 3f c0 7b d9Ca...

bhatok · 10-28-2010

Thanks for the response Peter. After monitoring this for a few days it seems the high RTO and SRTT move between the devices. Right now the switch has normal times and the other devices are much higher. The bandwidth for all the links is 1000Mbps and ...

bhatok · 10-25-2010

Can you swap the cables in the ports you think are having problems with another port and see if the problem follows the cable/device or stays with the switch port.If it follows the device it could be either the wiring or the device. At that point I w...

bhatok · 09-03-2010

Did this work for you and if so what version of IOS are you using on your 1310? I have tried this same setup but was not successful.Wireless clients work but the wired clients do not.Thanks,Brandon

Member Since	‎10-31-2003 10:01 AM
Date Last Visited	‎10-15-2024 01:58 PM
Posts	69

User Statistics

User Activity

only system vlans forward traffic on 1000v

EIGRP Flaps & SRTT differences

EIGRP SRTT difference between neighbors & EIGRP Flapping

NAC setup/authentication not working

WCS Mac Filter import file

only system vlans forward traffic on 1000v

only system vlans forward traffic on 1000v

Re: EIGRP SRTT difference between neighbors & EIGRP Flapping

Re: Switches shows specific interfaces UP and DOWN just briefly

Re: 1310 Wireless Repeater