Well, in the mean while the issue was reported to TAC, and they are starting an RMA procedure. It's a real issue, not a configuration mistake. Thanks all. ... View more

We found something in the log; 000905: Dec  5 07:03:09: %QM-SW1-2-VLAN_BASED_MODE_ON_EC_MEMBER_PORT: Port-channel705[0] and TenGigabitEthernet1/9/2[1] have different vlan-based mode 000906: 000102: Dec  5 07:03:09: %QM-SW2_STBY-2-VLAN_BASED_MODE_ON_EC_MEMBER_PORT: Port-channel705[0] and TenGigabitEthernet1/9/2[1] have different vlan-based mode could that be the cause of the issue? ... View more

Hi, we have found the cause of the issue. Raising buffers of turning of flow control did not change anything. However, we have found why there was such a limitation. We were using the build in Gb interface for LAN and a HWIC card for the WAN connection. After realising this it triggered us to search for issues with HWIC and found this: http://www.cisco.com/en/US/prod/collateral/routers/ps5855/prod_qas0900aecd8016a953.html Q. What is the maximum throughput of the four onboard HWIC slots? A. The maximum throughput per slot is up to 400 Mbps full duplex. The new Gigabit Ethernet HWIC and the 4- and 9-port Cisco EtherSwitch HWIC modules are able to take advantage of this performance improvement up to the switching capabilities of individual platforms. We did some reshuffling of the interfaces and were able to use the two build-in Gb interfaces, reconfigured, and the throughput is now just over 800Mb/sec, perfectly acceptable. Just to let you know. ... View more

The other two interfaces, facing the LAN: A side: show interfaces gigabitEthernet 0/1 GigabitEthernet0/1 is up, line protocol is up   Hardware is BCM1125 Internal MAC, address is 0022.55e6.9911 (bia 0022.55e6.9911)   Description: *** LAN ***   Internet address is 172.25.253.3/24   MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,      reliability 255/255, txload 1/255, rxload 1/255   Encapsulation ARPA, loopback not set   Keepalive not set   Full-duplex, 1000Mb/s, media type is RJ45   output flow-control is XON, input flow-control is XON   ARP type: ARPA, ARP Timeout 04:00:00   Last input 00:00:00, output 00:00:00, output hang never   Last clearing of "show interface" counters never   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: fifo   Output queue: 0/100 (size/max)   30 second input rate 234000 bits/sec, 55 packets/sec   30 second output rate 221000 bits/sec, 57 packets/sec      1197472585 packets input, 2490897503 bytes, 0 no buffer      Received 16605 broadcasts, 0 runts, 0 giants, 0 throttles      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored      0 watchdog, 7423595 multicast, 0 pause input      0 input packets with dribble condition detected      2604090893 packets output, 729062081 bytes, 0 underruns      1 output errors, 0 collisions, 1 interface resets      0 unknown protocol drops      0 babbles, 0 late collision, 0 deferred      1 lost carrier, 0 no carrier, 0 pause output      0 output buffer failures, 0 output buffers swapped out B side: show interfaces gigabitEthernet 0/1 GigabitEthernet0/1 is up, line protocol is up   Hardware is BCM1125 Internal MAC, address is 0022.90a8.bb31 (bia 0022.90a8.bb31)   Description: *** LAN ***   Internet address is 172.26.250.20/16   MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,      reliability 255/255, txload 3/255, rxload 1/255   Encapsulation ARPA, loopback not set   Keepalive not set   Full-duplex, 1000Mb/s, media type is RJ45   output flow-control is XON, input flow-control is XON   ARP type: ARPA, ARP Timeout 04:00:00   Last input 00:00:09, output 00:00:00, output hang never   Last clearing of "show interface" counters never   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0   Queueing strategy: fifo   Output queue: 0/100 (size/max)   5 minute input rate 533000 bits/sec, 638 packets/sec   5 minute output rate 15547000 bits/sec, 1307 packets/sec      381530928 packets input, 3569410611 bytes, 0 no buffer      Received 6558886 broadcasts, 0 runts, 0 giants, 0 throttles      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored      0 watchdog, 20221909 multicast, 0 pause input      0 input packets with dribble condition detected      1648728082 packets output, 1502180012 bytes, 0 underruns      1 output errors, 0 collisions, 1 interface resets      266 unknown protocol drops      0 babbles, 0 late collision, 0 deferred      1 lost carrier, 0 no carrier, 0 pause output      0 output buffer failures, 0 output buffers swapped out ... View more

Actually no, Gig 0/1 is the LAN interface, G0/0/0 is connected to the WAN service. Nothing else is connected to it, dedicated router. Gig 0/1 show interface output is eing retrieved now. How would i change the queue limit? Don't have much experience with this configuration. Do you do that with the hold queue command? ... View more

Sure: Side a: #show interfaces gigabitEthernet 0/0/0 GigabitEthernet0/0/0 is up, line protocol is up   Hardware is PM-3387, address is 0022.55e6.9913 (bia 0022.55e6.9913)   Description: LINE-ID V268575- ID 6467   Internet address is 10.10.10.1/30   MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,      reliability 255/255, txload 96/255, rxload 2/255   Encapsulation ARPA, loopback not set   Keepalive set (10 sec)   Full-duplex, 1000Mb/s, link type is autonegotiation, media type is SX   output flow-control is XON, input flow-control is XON   ARP type: ARPA, ARP Timeout 04:00:00   Last input 00:00:08, output 00:00:00, output hang never   Last clearing of "show interface" counters never   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 473316545   Queueing strategy: fifo   Output queue: 32/40 (size/max)   5 minute input rate 8473000 bits/sec, 14941 packets/sec   5 minute output rate 379344000 bits/sec, 31404 packets/sec      849214129 packets input, 1155482862 bytes, 29 no buffer      Received 226486 broadcasts, 0 runts, 0 giants, 1 throttles      0 input errors, 4 CRC, 4 frame, 0 overrun, 0 ignored      0 watchdog, 0 multicast, 51856 pause input      0 input packets with dribble condition detected      875497572 packets output, 3304958944 bytes, 0 underruns      0 output errors, 0 collisions, 2 interface resets      0 unknown protocol drops      0 babbles, 0 late collision, 0 deferred      4 lost carrier, 0 no carrier, 434 pause output      0 output buffer failures, 0 output buffers swapped out Side B: #show interfaces gigabitEthernet 0/0/0 GigabitEthernet0/0/0 is up, line protocol is up   Hardware is PM-3387, address is 0022.90a8.bb33 (bia 0022.90a8.bb33)   Description: LINE-ID V268575- ID 6467   Internet address is 10.10.10.2/30   MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,      reliability 255/255, txload 2/255, rxload 97/255   Encapsulation ARPA, loopback not set   Keepalive set (10 sec)   Full-duplex, 1000Mb/s, link type is autonegotiation, media type is SX   output flow-control is XON, input flow-control is XON   ARP type: ARPA, ARP Timeout 04:00:00   Last input 00:00:00, output 00:00:00, output hang never   Last clearing of "show interface" counters never   Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 10739   Queueing strategy: fifo   Output queue: 0/40 (size/max)   5 minute input rate 381081000 bits/sec, 31592 packets/sec   5 minute output rate 8602000 bits/sec, 15138 packets/sec      2413913293 packets input, 2051875065 bytes, 0 no buffer      Received 604359 broadcasts, 1 runts, 0 giants, 0 throttles      0 input errors, 9 CRC, 8 frame, 0 overrun, 0 ignored      0 watchdog, 0 multicast, 840 pause input      0 input packets with dribble condition detected      3218155929 packets output, 1071013994 bytes, 0 underruns      0 output errors, 0 collisions, 2 interface resets      0 unknown protocol drops      0 babbles, 0 late collision, 0 deferred      8 lost carrier, 0 no carrier, 254660 pause output      0 output buffer failures, 0 output buffers swapped out ... View more

Got it to work using this link: http://www.ccie1.com/?p=164 Converted it to standard VPN configig using a crypto map, works nicely. ... View more

Yes i can. I've put the step by step config in a document which i can send to you. I am a bit hesitant to attach it to this forum, is there an e-mail address i can send it to? ... View more

Same issue with connecting to an Ayava 430 unit using SSH from a C3750. ... View more

Ah, just found out that this is possible. You can disover templates from an connected controller. These can be use for new controllers... ... View more