HI,  you can use the functionality of Auto SmartPort Macro or Interface Template, second method is preferred. In short, then - in the first case, you configure the functionality of Auto SmartPort Macro and send in addition to "device-traffic-class = switch" the following cisco-av-pair - "auto-smart-port = aspName", in the macro you write something like "switchport trunk native vlan 100" - in the second case, you configure the Interface Template and send in addition to "device-traffic-class = switch" the next cisco-av-pair - "interface-template-name = templateName", in this template write something like "switchport trunk native vlan 100" I do not recommend the first method, I hope your switches support Interface Template, otherwise you will have to understand the Auto SmartPort Macro technology well before implementation. With the Interface Template everything is much simpler, a good example you will find in this community - https://community.cisco.com/t5/security-documents/neat-with-interface-template/ta-p/3642967     ... View more

Hi, just do it, worked as expected... NX5548-1# sh run int e101/1/1 !Command: show running-config interface Ethernet101/1/1 !Time: Mon Jun 17 09:22:15 2019 version 5.2(1)N1(3) interface Ethernet101/1/1 inherit port-profile NoLLDP description pcterm 1 no cdp enable spanning-tree bpdufilter disable NX5548-1# sh run int e101/1/1 expand-port-profile !Command: show running-config interface Ethernet101/1/1 expand-port-profile !Time: Mon Jun 17 09:22:21 2019 version 5.2(1)N1(3) interface Ethernet101/1/1 description pcterm 1 no lldp transmit no lldp receive no cdp enable spanning-tree bpdufilter disable NX5548-1# sh lldp interface e101/1/1 Interface Information: Enable (tx/rx/dcbx): N/N/N Port Mac address: f0:78:16:eb:54:a2 NX5548-1# ... View more

Hi, logically yes, did not check  on practice (I will do it Monday)... Cause there is no lldp commands under switch-profile (conf sync) you should define port-profile with disable LLDP via "conf t" on both parent switch, then apply this port-profile to FEX interfaces via "conf sync".   ... View more

Just talking with TAC, they said that: "The lldp commands are not switch-profile aware and won’t be able to configure them using "config sync". So you need to do configure via "conf t." ... View more

> You cannot disable LLDP on FEX switch it will have to disabled on the mother switch... I do not quite understand you, I'm trying to disable LLDP on FEX interfaces on the parent switch, cause LLDP run on FEX interface: ___________________________________________________________ NX5548-1# sh lldp interface ethernet 101/1/1 Interface Information: Enable (tx/rx/dcbx): Y/Y/Y Port Mac address: f0:78:16:eb:54:a2 ___________________________________________________________ NX5548-1# conf sync Enter configuration commands, one per line. End with CNTL/Z. NX5548-1(config-sync)# switch-profile card Switch-Profile started, Profile ID is 1 NX5548-1(config-sync-sp)# interface e101/1/1 NX5548-1(config-sync-sp-if)# no l? lacp Configure LACP parameters link Configure link load-interval Specify interval for load calculation for an interface NX5548-1(config-sync-sp-if)# ___________________________________________________________ ... View more

Hi,  1) on 3750x vlan 1 is shutdown:   c3750x-211.1#sh ip igmp interface vlan 1 Vlan1 is administratively down, line protocol is down   Internet protocol processing disabled c3750x-211.1#sh ip pim neighbor vlan 1                     ^ % Invalid input detected at '^' marker. c3750x-211.1#sh ip pim interface vlan 1 count                     ^ % Invalid input detected at '^' marker. c3750x-211.1#ping  239.255.9.116 repeat 10 source vlan 1 % Invalid source interface - IP not enabled or interface is down c3750x-211.1#ping  239.255.9.116 repeat 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 239.255.9.116, timeout is 2 seconds: .......... c3750x-211.1# 2) on 4948 vlan 1 is not ip address: c4948-211.1#sh ip igmp interface vlan 1 Vlan1 is up, line protocol is up Internet protocol processing disabled c4948-211.1#sh ip pim neighbor vlan 1 PIM Neighbor Table Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority, P - Proxy Capable, S - State Refresh Capable Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode c4948-211.1#sh ip pim interface vlan 1 count State: * - Fast Switched, D - Distributed Fast Switched H - Hardware Switching Enabled Address Interface FS Mpackets In/Out c4948-211.1#ping 239.255.9.116 repeat 10 source vlan 1 % Invalid source interface - IP not enabled or interface is down c4948-211.1#ping 239.255.9.116 repeat 10 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 239.255.9.116, timeout is 2 seconds: .......... c4948-211.1# 3) on c6500: c6500#sh ip igmp interface vlan 1 Vlan1 is up, line protocol is up Internet address is 10.0.1.194/21 IGMP is enabled on interface Current IGMP host version is 2 Current IGMP router version is 2 IGMP query interval is 60 seconds IGMP configured query interval is 60 seconds IGMP querier timeout is 120 seconds IGMP configured querier timeout is 120 seconds IGMP max query response time is 10 seconds Last member query count is 2 Last member query response interval is 1000 ms Inbound IGMP access group is not set IGMP activity: 3029 joins, 3014 leaves Multicast routing is enabled on interface Multicast TTL threshold is 0 Multicast designated router (DR) is 10.0.1.194 (this system) IGMP querying router is 10.0.1.194 (this system) Multicast groups joined by this system (number of users): 224.0.1.40(2) IGMP snooping is globally enabled IGMP snooping CGMP-AutoDetect is globally enabled IGMP snooping is enabled on this interface IGMP snooping fast-leave (for v2) is disabled IGMP snooping querier is disabled. IGMP snooping explicit-tracking is enabled IGMP snooping last member query response interval is 1000 ms IGMP snooping report-suppression is enabled IGMP snooping query interval is 60000 ms IGMP snooping querier version is 3 IGMP snooping querier - TCN query count is 2 IGMP snooping querier - TCN query interval is 10000 ms c6500#sh ip pim neighbor vlan 1 PIM Neighbor Table Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority, P - Proxy Capable, S - State Refresh Capable, G - GenID Capable Neighbor Interface Uptime/Expires Ver DR Address Prio/Mode c6500#sh ip pim interface vlan 1 count State: * - Fast Switched, D - Distributed Fast Switched H - Hardware Switching Enabled Address Interface FS Mpackets In/Out 10.0.1.194 Vlan1 * H 123376/53612 c6500#ping 239.255.9.116 repeat 10 source vlan 1 Type escape sequence to abort. Sending 10, 100-byte ICMP Echos to 239.255.9.116, timeout is 2 seconds: Packet sent with a source address of 10.0.1.194 .......... c6500# also, there is no command "sh mac address-table multicast igmp-snooping" on 3750x unlike 4948: c3750x-211.1#show mac address-table multicast ?   count         Count Keyword   mld-snooping  Addresses learned by MLD Snooping   user          User entered(static) addresses   vlan          vlan number   |             Output modifiers   <cr> c4948-211.1#sh mac address-table multicast ? count Count Keyword igmp-snooping Addresses learned by IGMP Snooping mld-snooping Addresses learned by MLD Snooping user User entered(static) addresses vlan vlan number | Output modifiers <cr>     ... View more

Hi, see attached files... ... View more

I'm sorry, I did not specify in the first message - ACI APIC... ... View more

Thanks for quick reply... So, in new multi-site deployment ACI-AD-XF license for each leaf is needed? What about MACsec on a spine, ACI licensing model is are leaf based, so do I need additional license for MACsec on spine? ... View more

Thanks for info,  in release that my wlc running (8.2.167.6) "s how advanced 802.11b txpower" not working, but "how advanced 802.11-abgn summary "  give some info, not such detailed, but txpower is present Excuse for troubling...   ... View more

this AP not contains a dedicated 2.4–GHz radio, it contains a Flexible Radio, so if you type "show advanced 802.11-abgn summary" you can see txpower This output from my WLC: (wlc5520-usc) >show advanced 802.11-abgn summary Member RRM Information AP Name MAC Address Slot Admin Oper Channel TxPower -------------------------------- ----------------- ---- -------- ----------- ------------------ ------------- APA023.9F66.2AE2 18:80:90:02:3a:20 0 ENABLED UP 13* *2/6 (13 dBm) APA023.9FAE.EDF2 18:80:90:0e:23:20 0 ENABLED UP 5* *5/6 ( 4 dBm) AP00A3.8EFA.DF50 40:ce:24:fb:cc:40 0 ENABLED UP 13* *5/6 ( 4 dBm) APA023.9FAE.EDC4 18:80:90:0e:20:40 0 ENABLED UP 13* *5/6 ( 4 dBm) APA023.9FAE.ED8E 18:80:90:0e:1c:e0 0 ENABLED UP 9* *2/6 (13 dBm)     ... View more