If you are using HTTPS to access the controller, you need to enter the following CLI command: "config network secureweb enable" This command allows users to access the controller GUI using “https://ip-address.” The default value is enabled. Secure web mode is a secure connection. Enter "show network summary" and verify.   ***Please rate all useful responses*** Jagan     ... View more

  I think  you'll need Assurance licenses in order to get netflow/AVC statistics/flows displayed on the PI. Check your PI licenses.   Here is another good post you can refer: https://community.cisco.com/t5/other-wireless-mobility-subjects/netflow-configuration-in-wlc-and-its-visibility-in-cisco-prime/td-p/3015444   Jagan ... View more

Yes, you can convert 1852 ME  to CAPWAP and join the 3504 WLC.   1.  connect to the AP console port 2. Go into AP Cisco Shell: (Cisco Controller) > apciscoshell 3.   Log back into the AP again Go into enable mode: (Cisco Controller) > en 4. Change to CAPWAP mode: (Cisco Controller) > ap-type capwap The AP will reboot one more time, then it will be in CAPWAP mode.   ***Please rate all useful posts*** Jagan ... View more

I would look at the AP Group configuration first. Make sure SSID are added to the AP Groups.   Go to WLANs --> Advanced --> AP Groups --> Select the AP Group -->WLANs   Your SSIDs should be added with correct interface mapping & APs should be part of this AP group. If it's default-group, then all WLANs/SSID will be added to it by default.    ***Please rate all helpful responses*** Jagan     ... View more

CON-SNT-CT5508 will give you 50 AP renewal only. I think you need CON-ECMU-LCT250A or L-CON-ECMU-LCT250A  You can re-host the AP capacity license (250) to another 5508 WLC in case of RMA by contacting Cisco licensing team.   ***Please rate all helpful responses***   Jagan ... View more

You can also use Cisco Prime Infrastructure to generate existing AP heat maps or use Planning Mode to  calculate the recommended number and location of access points based on whether data and/or voice traffic and/or location are active.   There are some non-Cisco tools available such as Ekahau, AirMagnet etc.   Jagan ... View more

Cisco 1562i doesn't have Autonomous code. It supports Lightweight & Mobility Express. However, Mesh is not supported with Mobility Express. Its supported only on WLC with code 8.4 for 1560 series outdoor APs.   Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-7/b_feature_matrix_for_802_11ac_wave2_access_points.html     ***Please rate all useful posts*** Jagan       ... View more

You can look at the following vendors who provide mounting hardware https://oberoninc.com/ http://acceltex.com/ http://www.ventevinfra.com/   All of them have AP+antenna co-located mounting options.   ***Please rate all helpful responses*** Jagan ... View more

The VLANs are for reference only and they may not be the same that you've on your network. If you are not well versed with this network configurations, it's always good to engage someone who knows about the network or contact Cisco TAC to get help.     ... View more

1. It's always good to have ME and APs on the same code to start with. However, it's not possible all the time and you will end up having them running on different versions like you've now.    The master AP facilitates transfer of image from TFTP to the new AP which is added. You can find the process from the link below. https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-2/b_Mobility_Express_Deployment_guide/b_Mobility_Express_Deployment_guide_chapter_01010.html   2. A Network Time Protocol (NTP) server can be configured to synchronize date and time if one was not configured during the Wireless Express setup. You can add your switch or router as NTP server in ME.  A step-by-step process is documented here https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-2/b_Mobility_Express_Deployment_guide/b_Mobility_Express_Deployment_guide_chapter_01000.html#task_070E1CD5592E49FB88794483D39BB02D   For your country, a simple google search showed me: Tunisia Time Zone- is abbreviated as CET(Central European Time) Tunisia is GMT/UTC + 1h Standard Time  I think (GMT+1 Amsterdam, Berlin, Rome, Vienna) is correct for your time zone, but I may be wrong. Please review your time zone configs for other network devices or someone who knows your region can answer that.   Please go through the above Mobility Express Deployment Guide thoroughly and you can find all answers explained in detail.   Jagan     ... View more

Here is the problem: Discovery Request received on wrong VLAN '0' on interface '1', management VLAN = '1', AP Manager VLAN = '1', dropping the packet   make sure your APs are on the correct VLAN and the same VLAN is allowed on the trunk port where ME is connected to.   Configuring the Switch Port   Connect the access points to the switch and power them up. Ensure the following while configuring the switch port: All access points, including the Master AP, in a Mobility Express network should be in the same L2 broadcast domain. Management traffic must not be tagged.   The switch port to which the Master AP is connected can be a trunk port or an access port and must be configured to trunk Native VLAN for management traffic. Data traffic must be trunked with appropriate VLANs for local switching as well.   The following is a sample switch port configuration for ME. Interface GigabitEthernet1/0/37 description » Connected to Master AP « switchport trunk encapsulation dot1q (Newer switches/CatOS don't require this command) switchport mode trunk switchport trunk native vlan 122 switchport trunk allowed vlan 10,20,122   The following is a sample switch port configuration for AP   Interface GigabitEthernet1/0/15 description » AP « switchport mode access switchport access vlan 122 ... View more

I see the following issues:  1. Country code selected as IL & US. If you are using  AIR-AP1832I-I-K9 only model, then you don't need WLC to support US.  2.  AP stuck at "waiting for uplink IP address and reachable default gateway:". Can you connect a laptop to the switch port where one of these APs are connected to and see if you get an IP Address assigned and can ping WLC management interface.   You can try assigning an IP address statically on your AP and see if it fixes the problem.   Console into the AP and AP# debug capwap console cli AP#capwap ap ip address <IP address> <subnet mask> AP#capwap ap ip default-gateway <IP-address> AP#capwap ap controller ip address <IP-address> AP#capwap ap hostname <name> (optional)   Can you post the AP console output as well.   Jagan   ... View more

if i put router as server DHCP   so ME 1815   What is his role  !!!! get ip addres from router or it remain ip managment 1.1.1.21 with 255.255.255.0 and gateway 1.1.1. 1 Configure a DHCP server on the switch or externally so that Cisco 1815 Access Point can obtain an IP address at boot up.  ME 1815 has two roles here. 1. Wireless Controller 2. Access Point. ME 1815 configured as WLC is also an Access Point, which requires an IP Address to join itself (WLC). This 1815 AP replies on an external DHCP server to get an ip assigned, so that it can initiate CAPWAP session with self (WLC). The DHCP server also assigns IP address to other APs and wireless clients. So, 1815 AP gets an IP Address from the router & WLC will have the mgmt interface ip address which is 1.1.1.21 in your case.   2)  what pool is configured in router that AP discover ME ( WLC ) !!! 1.1.1.22 or 1.1.1.0 /24  !!!!!!!!!!!!! I don't know your router capabilities, but in general you can configure 1.1.1.0/24 and exclude IPs until 1.1.1.21   3)  why ME to be server DHCP ?????,  and disable DHCP on router so my be AP get ip address from ME???, https://www.cisco.com/c/en/us/support/docs/wireless/mobility-express/210531-Mobility-Express-Internal-DHCP.html     4) version AP 1815i 8.3.111 and ME 8.8.100 :  is good or not ???, AP and ME can't run different code versions. You'll need to setup a TFTP server and any AP join the ME will get the software download from it to be in sync with ME. 8.1-8.4 – Not recommended due stability and enhancements done in newer releases For Mobility Express deployments, TAC recommends using the 8.5.140.0 or 8.8.111.0 release.   ***Hope this helps*** Jagan ... View more