Hi, User-A calls to user-B, when user-A press conference and dial no. of user-C, ( user-A and user-C remains connected, while user-B goes on hold ), and if we press swap, user-A connected to user-B, while user-C goes on hold. MRGL and MRG is configured as well. -Waleed ... View more

Cisco 7821 working as a SIP stuck at "Registering" once it loss the connectivity with CUCM, ( Using CUCM 11.0 ) even after getting connectivity from CUCM, it remains unregister, lets suppose a 7821 is register with CUCM, once we remove CUCM lan cable, 7821 should be unregistered but after plugging the lan cable to CUCM, the 7821 should register also, but 7821 SIP phone remain unregister while other SCCP phone got register automatically, the only solution untill now is removing the POE cable from phone and plugin back so it restart it, then 7821 register otherwise not, anyone have a Idea what is the problem ? -W ... View more

Dear All,   i am using Prime, SNMP v3 working OK,  debugs for it is below Sep  9 06:08:51.934: SNMP: Packet received via UDP from 10.50.6.243 on Vlan194 Sep  9 06:08:51.935: SNMP: Get request, reqid 2110959961, errstat 0, erridx 0   sysUpTime.0 = NULL TYPE/VALUE Sep  9 06:08:51.936:  Incoming SNMP packet Sep  9 06:08:51.936: v3 packet  security model: v3       security level: priv   but when I am using Ipatch server I am getting only this debugs log   Sep  9 06:08:25.665: SNMP: Packet received via UDP from 10.50.196.74 on Vlan194     Prime IP: 10.50.6.243 Ipatch Server IP: 10.50.196.74   Although on Ipatch server SNMPv2 working perfactly. AnyIdea where the problem exist ?   - Waleed ... View more

Hi,   I get a query recently, anyone know how to list/search all those phones on which call forwarding is set in call manager 8.6 or above.   - Waleed ... View more

I am using Cisco 4507, when I try to connect Cisco Switch with Dlink Power over Ethernet Adapter Kit DWL-P200, port is not getting up, I try Dlink adapter with other vendor switch its getting UP, I check the debugs when I connect Dlink with Cisco Switch, I get this log on cisco switch.   Jul 14 11:45:48.456: ilpower_interface_enable: interface (Gi6/41) enable: 1 Jul 14 11:45:48.456: ilpower_powerman_power_available_tlv: about sending patlv on Gi6/41 Jul 14 11:45:48.456:  req id 0, man id 1, pwr avail 15004, pwr man -1   I try to change the power inline to maximum/minimum and a value in between but its not working.   #show power inline                              Watts Used of System Power(12V) Mod   Model                 budgeted instantaneous  peak   out of reset  in reset ----  -------------------   -------- ------------- ------  ------------  -------- Gi6/41    auto off        0.0      0.0       n/a                 n/a #show power inline                              Watts Used of System Power(12V) Mod   Model                 budgeted instantaneous  peak   out of reset  in reset ----  -------------------   -------- ------------- ------  ------------  -------- Gi6/41    static off        32.3       30.0       n/a                 n/a #show power inline                              Watts Used of System Power(12V) Mod   Model                 budgeted instantaneous  peak   out of reset  in reset ----  -------------------   -------- ------------- ------  ------------  -------- Gi6/41    static off        16.4       16.4       n/a                 n/a   # #show power detail Power                                             Fan      Inline Supply  Model No          Type       Status       Sensor   Status ------  ----------------  ---------  -----------  -------  ------- PS1     PWR-C45-4200ACV   AC 4200W   good         good     good    PS1-1                         220V   good          PS1-2                         220V   good          PS2     PWR-C45-4200ACV   AC 4200W   good         good     good    PS2-1                         220V   good          PS2-2                         220V   good          Power supplies needed by system    : 1 Power supplies currently available : 2 Power Summary                      Maximum  (in Watts)              Used     Available ----------------------   ----     --------- System Power (12V)        991        1360 Inline Power (-50V)       214        3169 Backplane Power (3.3V)     40          40 ----------------------   ----     --------- Total                    1245 (not to exceed Total Maximum Available = 4200) Power Measurement    Inline Power (-50V) (in Watts)             (+/- 50Watts) ------------------   ------------------- PS1                         100 PS2                         100 ------------------   ------------------- Total                       200 Power fail interrupts received on slot 1: 0 Power fail interrupts received on slot 2: 0 Debounce value for power fail status: 0 microseconds                              Watts Used of System Power(12V) Mod   Model                 budgeted instantaneous  peak   out of reset  in reset ----  -------------------   -------- ------------- ------  ------------  --------  1    WS-X4648-RJ45V+E          92         --        --         92          10  2    WS-X4748-RJ45V+E          75          45        46        75          35  3    WS-X45-SUP8-E            400         210       219       400         205  5    WS-X4748-RJ45V+E          75          45        46        75          35  6    WS-X4648-RJ45V+E          92         --        --         92          10  7    WS-X4648-RJ45V+E          92         --        --         92          10  --   Fan Tray                 165         --        --        --          -- -------------------------   -------- ------------- ------  ------------  --------        Total                   991         300       311       826         305                         Watts used of Chassis Inline Power (-50V)                         Inline Power Admin  Inline Power Oper Mod   Model                PS     Device       PS     Device     Efficiency ----  -------------------  ----------------    ----------------    ----------  1    WS-X4648-RJ45V+E        28       26         13       12          93  2    WS-X4748-RJ45V+E        27       26         12       11          95  3    WS-X45-SUP8-E            -        -          -        -           -  5    WS-X4748-RJ45V+E        79       75         24       22          95  6    WS-X4648-RJ45V+E        63       59         15       13          93  7    WS-X4648-RJ45V+E        17       16          9        8          93 -------------------------  ----------------    ----------------    ----------        Total                 214      202         73       66         Dlink Adapter: Voltage (Power Supply) Input: 100-240V AC, 50/60Hz Output: 48V DC, 400mA   Power over Ethernet Adapter Kit Category 5 (CATS) Ethernet Pin Usage   Data: 1,2,3,6 Power: 4,5,7,8 LEDs Power (Base Unit) Power (Terminal Unit) Voltage (Power Supply) Input: 100-240V AC, 50/60Hz Output: 48V DC, 400mA     -- Kind Regards, Waleed Khan ... View more