About bastienbertout

IM Only User · 02-27-2014

Hi,I configured a user with IM Only (just IM in service profile) but Jabber For windows stills try to connect to CCMCIP for the softphone and, of course, I get an error.I also tried to set the service profile to "none" on the user and just let "enabl...

User with Jabber iPad + Jabber Windows · 02-27-2014

Hi,Is it possible to have a functional directory config for a user having 2 jabber devices : 1 JFW + 1 Jabber iPad in 9.6 release ?- UDS does not seem to work well- JFW uses EDI does not seem to work with BDI- Jabber for iPad uses BDI and does not se...

bastienbertout · 06-01-2012

Hi,Is it possible to transcode NSE based T.38 to protocol based T.38 whit a CUBE ?I would like to have NSE based T.38 between CUCM6.1 and CUBE. And protocol based T.38 between CUBE and my SIP trunk provider.If this is possible, can I do it in softwar...

bastienbertout · 05-30-2012

Hi,My customer is migrating is ToIP infrastructure from traditionnal gateway with E1s to a SIP Trunk.I have to implement the design below :VG224 <---sccp---> CUCM 6.1.4 <---sip trunk----> ProviderandSagemXmediusFaxServer <---H323---> CUCM 6.1.4 <---s...

bastienbertout · 11-25-2011

Hi,I would like to deploy a MeetingPlace 8.5 Server.It's seems there is no specific 8.5 reference to order. So I ordered "MP8-SW".In the configuration guide, there is no way to indicate that we want 8.5 DVDs.And, when I received my CDs, the version w...

bastienbertout · 12-05-2012

Hi,I also have to upgrade from 4.1.3 to 9.X.My customer only has 100 users / devices.As you mentioned, it seems to me that it's much easier to do a clean install of 9.X, to reconfigure everything except devices/users and then to do BAT export devices...

bastienbertout · 06-05-2012

Thanx for your answer !

bastienbertout · 06-05-2012

Thanx for your help.Finally, I found that, for an unknown reason, all calls were redirected to a transcoder by CUCM.So, I configured an MRG/MRGL with no transcoder and associated it to the trunk.Now, all calls are OK between endpoint and SIP provider...

bastienbertout · 06-01-2012

Hi, I made the changes and still have the same behavior.488 error : Media not accepted in SIP traces sent by CUCM to SIP Provider's SBC when this one announce T.38 capabilities.best regards,Bastien.

bastienbertout · 06-01-2012

Thanx. I already tried this but the SIP provider does not support NSE based T.38....

Member Since	‎05-13-2009 09:11 AM
Date Last Visited	‎08-18-2017 04:03 AM
Posts	58
Total Helpful Votes Received	5

User Statistics

User Activity

IM Only User

User with Jabber iPad + Jabber Windows

CUBE to transcode NSE based T.38 to protocol based T.38 ?

CUCM 6.1 and T.38 through SIP Trunk Provider

Has anyone been able to install MeetingPlace 8.5 ?

Re: CM 4.1 Migration to 9.0

CUBE to transcode NSE based T.38 to protocol based T.38 ?

Re: CUCM 6.1 and T.38 through SIP Trunk Provider

Re: CUCM 6.1 and T.38 through SIP Trunk Provider

CUCM 6.1 and T.38 through SIP Trunk Provider