Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Muhammad Tahir Munir
01-26-2019
Stats
Member since
01-18-2010
19
Posts
10
Helpful
0
Solutions
Created by
Muhammad Tahir Munir
in Switching
in Switching
01-20-2019
04:18 AM
01-20-2019
04:18 AM
Thanks its works for me!
... View more
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
03-01-2013
11:45 PM
03-01-2013
11:45 PM
hi, 1. Install adv video pie. 2. Install adv-video-license (a9k-adv-video-lic is a chassis based license, not a slot based license so you need only one license for chasis) 3. Go to admin config mode and assign to all slots, check below config. i.e: license A9K-ADV-VIDEO-LIC location all 4. Here is an example for enabling video-monitoring: ! ipv4 access-list sample-acl-1 10 permit udp any any ! class-map type traffic match-any sample-class-1 match access-group ipv4 sample-acl-1 end-class-map ! policy-map type performance-traffic sample-policy class type traffic sample-class-1 monitor parameters interval duration 10 history 60 timeout 3 flows 300 ! monitor metric ip-cbr rate layer3 packet 100 pps ! react 100 flow-count threshold type immediate threshold value gt 270 action syslog alarm severity critical ! end-policy-map interface GigabitEthernet0/0/0/0 ipv4 address 1.1.1.1 255.255.255.0 service-policy type performance-traffic input sample-policy now you can see RSP0 in show license
... View more
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
02-26-2013
05:07 AM
02-26-2013
05:07 AM
hi, Cisco ASR 9000 Series Per Chassis Advanced Video License. How to assign to chassis? Regards Muhammad Tahir Munir
... View more
Labels:
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
02-26-2013
04:59 AM
02-26-2013
04:59 AM
hi, I have asr9k i want to assign video license to slot but i unable to do anyone help me..:) FeatureID: A9K-ADV-VIDEO-LIC (Slot based, Permanent) Total licenses 3 Available for use 3 Allocated to location 0 Active 0 Store name Permanent Store index 1 Pool: Owner Total licenses in pool: 3 Status: Available 3 Operational: 0 FeatureID: A9K-AIP-LIC-B (Slot based, Permanent) Total licenses 3 Available for use 0 Allocated to location 0 Active 3 Store name Permanent Store index 2 Pool: Owner Total licenses in pool: 3 Status: Available 0 Operational: 3 Locations with licenses: (Active/Allocated) [SDR] 0/3/CPU0 (1/0) [Owner] 0/4/CPU0 (1/0) [Owner] 0/5/CPU0 (1/0) [Owner] RP/0/RSP1/CPU0:PER05# RP/0/RSP1/CPU0:PER05(admin)#sh run Building configuration... !! IOS XR Admin Configuration 4.3.0 username admin group root-system secret 5 xxxxxxxxxx. ! license A9K-AIP-LIC-B location 0/3/CPU0 location 0/4/CPU0 location 0/5/CPU0 ! license A9K-ADV-VIDEO-LIC location 0/RSP0/CPU0 location 0/3/CPU0 location 0/4/CPU0 location 0/5/CPU0 ! end RP/0/RSP1/CPU0:PER05(admin)# Regards Muhammad Tahir Munir
... View more
Labels:
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-09-2012
04:32 AM
10-09-2012
04:32 AM
Router 1 config outup: --------------------------------- RP/0/RSP0/CPU0:9010-1#sh run int bundle-ether 12 Tue Oct 9 14:26:10.591 KSA interface Bundle-Ether12 description "EtherChannel to 9010-2" mtu 9216 service-policy output EGRESS-NNI ipv4 address 10.0.1.30 255.255.255.252 ipv4 unreachables disable bundle minimum-active links 1 bundle minimum-active bandwidth 10000000 load-interval 30 dampening ! RP/0/RSP0/CPU0:9010-1#show isis interface bundle-ether12 Tue Oct 9 14:25:56.600 KSA Bundle-Ether12 Enabled Adjacency Formation: Enabled Prefix Advertisement: Enabled BFD: Disabled BFD Min Interval: 150 BFD Multiplier: 3 Circuit Type: level-2-only Media Type: P2P Circuit Number: 0 Extended Circuit Number: 134218016 Next P2P IIH in: 9 s LSP Rexmit Queue Size: 0 Level-2 Adjacency Count: 1 LSP Pacing Interval: 33 ms PSNP Entry Queue Size: 0 CLNS I/O Protocol State: Up MTU: 9199 SNPA: b414.89e0.9f99 Layer-2 MCast Groups Membership: All ISs: Yes IPv4 Unicast Topology: Enabled Adjacency Formation: Running Prefix Advertisement: Running Metric (L1/L2): 10/10 MPLS LDP Sync (L1/L2): Disabled/Enabled Sync Status: Achieved IPv4 Address Family: Enabled Protocol State: Up Forwarding Address(es): 10.0.1.30 Global Prefix(es): 10.0.1.28/30 LSP transmit timer expires in 0 ms LSP transmission is idle Can send up to 9 back-to-back LSPs in the next 0 ms RP/0/RSP0/CPU0:9010-1# RP/0/RSP0/CPU0:9010-1# RP/0/RSP0/CPU0:9010-1#sh run router isis Tue Oct 9 14:26:41.010 KSA router isis core net 49.0001.0100.0000.0003.00 nsf cisco lsp-gen-interval maximum-wait 5000 initial-wait 1 secondary-wait 50 level 2 lsp-refresh-interval 65000 level 2 max-lsp-lifetime 65535 level 2 address-family ipv4 unicast metric-style wide spf-interval maximum-wait 5000 initial-wait 1 secondary-wait 50 redistribute static route-policy STATIC-TO-ISIS redistribute ospf 100 route-policy RP-FROM-OSPF-TO-ISIS ! interface Bundle-Ether12 circuit-type level-2-only point-to-point hello-padding disable level 2 hello-password keychain ISIS-key address-family ipv4 unicast metric 10 level 2 mpls ldp sync level 2 ! Router 2 output config: -------------------------------- RP/0/RSP0/CPU0:9010-2#sh run int bundle-ether 21 Tue Oct 9 14:24:11.346 KSA interface Bundle-Ether21 description "EtherChannel to 9010-1 mtu 9216 service-policy output EGRESS-NNI ipv4 address 10.0.1.29 255.255.255.252 bundle minimum-active links 1 bundle minimum-active bandwidth 10000000 dampening ! RP/0/RSP0/CPU0:9010-2# RP/0/RSP0/CPU0:9010-2#show isis interface bundle-ether21 Tue Oct 9 14:23:48.457 KSA Bundle-Ether21 Enabled Adjacency Formation: Enabled Prefix Advertisement: Enabled BFD: Disabled BFD Min Interval: 150 BFD Multiplier: 3 Circuit Type: level-2-only Media Type: P2P Circuit Number: 0 Extended Circuit Number: 134218208 Next P2P IIH in: 6 s LSP Rexmit Queue Size: 0 Level-2 Adjacency Count: 1 LSP Pacing Interval: 33 ms PSNP Entry Queue Size: 0 CLNS I/O Protocol State: Up MTU: 9199 SNPA: 0026.980e.d3e2 Layer-2 MCast Groups Membership: All ISs: Yes IPv4 Unicast Topology: Enabled Adjacency Formation: Running Prefix Advertisement: Running Metric (L1/L2): 10/10 MPLS LDP Sync (L1/L2): Disabled/Enabled Sync Status: Achieved IPv4 Address Family: Enabled Protocol State: Up Forwarding Address(es): 10.0.1.29 Global Prefix(es): 10.0.1.28/30 LSP transmit timer expires in 0 ms LSP transmission is idle Can send up to 9 back-to-back LSPs in the next 0 ms RP/0/RSP0/CPU0:9010-2# RP/0/RSP0/CPU0:9010-2#sh run router isis Tue Oct 9 14:24:41.457 KSA router isis core net 49.0001.0100.0000.0002.00 nsf cisco log adjacency changes lsp-gen-interval maximum-wait 5000 initial-wait 1 secondary-wait 50 level 2 lsp-refresh-interval 65000 level 2 max-lsp-lifetime 65535 level 2 address-family ipv4 unicast metric-style wide spf-interval maximum-wait 5000 initial-wait 1 secondary-wait 50 ! interface Bundle-Ether21 circuit-type level-2-only point-to-point hello-padding disable level 2 hello-password keychain ISIS-key address-family ipv4 unicast metric 10 level 2 mpls ldp sync level 2 !
... View more
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-08-2012
04:56 AM
10-08-2012
04:56 AM
hi, why this log message keep appearing?? RP/0/RSP0/CPU0:9010-2# RP/0/RSP0/CPU0:9010-2#RP/0/RSP0/CPU0:Oct 8 14:50:37.023 : isis[1001]: %ROUTING-ISIS-4-P2P_CONFIG_MISMATCH : L2 hello-padding configuration on P2P interface Bundle-Ether21 will not be used RP/0/RSP0/CPU0:9010-2# On both side hello padding is disable for level 2. ! interface Bundle-Ether22 circuit-type level-2-only point-to-point hello-padding disable level 2 hello-password keychain ISIS-key address-family ipv4 unicast metric 10 level 2 mpls ldp sync level 2 ! regards tahir
... View more
Labels:
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-08-2012
12:58 AM
10-08-2012
12:58 AM
Please check below output. RP/0/RSP0/CPU0:9010-1#sh install log 19 detai Mon Oct 8 10:56:53.956 KSA Install operation 19 started by user 'admin' via CLI at 16:50:39 KSA Sun Oct 07 2012. (admin) install add /disk0:asr9k-video-p.pie-4.0.3 Install operation 19 failed at 16:50:48 KSA Sun Oct 07 2012. Install logs: Install operation 19 '(admin) install add /disk0:asr9k-video-p.pie-4.0.3' started by user 'admin' via CLI at 16:50:39 KSA Sun Oct 07 2012. Error: The install operation failed due to a system error. Please collect diagnostic information using 'show tech-support install' and pass this information to your TAC Error: representative for support. Error: Errors occurred on the following node: Error: 0/RSP1/CPU0 ('install pie get reply' message response reported failure: 'Package Library' detected the 'fatal' condition 'file I/O error': File exists) Install operation 19 failed at 16:50:48 KSA Sun Oct 07 2012. -------------------------------------------------------------------------------- RP/0/RSP0/CPU0:9010-1#
... View more
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-08-2012
12:55 AM
10-08-2012
12:55 AM
yes working install add compactflash:/c12k-diags-3.9.0 sync
... View more
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-07-2012
04:59 PM
10-07-2012
04:59 PM
hi, please help me how i can copy this file c12k-diags-3.9.0 to disk0: RP/0/0/CPU0:IOS-XR1#dir Sun Oct 7 16:50:41.165 UTC Directory of compactflash:/usr 2300706944 -rwx 21478082 Sat Sep 29 07:34:26 2012 c12k-diags.pie-3.9.0 2300707040 -rwx 23288472 Sat Sep 29 07:37:56 2012 c12k-fpd.pie-3.9.0 2300707136 -rwx 5208671 Sat Sep 29 07:38:58 2012 c12k-k9sec.pie-3.9.0 2300707232 -rwx 7500964 Sat Sep 29 07:39:30 2012 c12k-mcast.pie-3.9.0 2300707328 -rwx 7585845 Sat Sep 29 07:40:01 2012 c12k-mgbl.pie-3.9.0 2300707424 -rwx 3924750 Sat Sep 29 07:41:51 2012 c12k-mpls.pie-3.9.0 2300707520 -rwx 3991532 Sat Sep 29 07:44:56 2012 c12kprp-boot-mz.120-32.SY5 2300707616 -rwx 27977652 Sat Sep 29 07:45:46 2012 c12kprp-p-mz.120-32.SY5 2300707712 -rwx 15401432 Sat Sep 29 07:53:38 2012 mbiprp-drp.vm-3.9.0 2300707808 -rwx 15213364 Sat Sep 29 07:54:27 2012 mbiprp-rp.vm-3.9.0 4186599424 bytes total (3495657472 bytes free) RP/0/0/CPU0:IOS-XR1# RP/0/0/CPU0:IOS-XR1# RP/0/0/CPU0:IOS-XR1#show install inactive summary Sun Oct 7 16:47:45.287 UTC Inactive Packages: compactflash:c12k-diags-3.9.0 RP/0/0/CPU0:IOS-XR1#copy compactflash:c12k-diags-3.9.0 disk0: Sun Oct 7 16:48:02.457 UTC Destination filename [/disk0:/c12k-diags-3.9.0]? %Error copying compactflash:/c12k-diags-3.9.0 (Source cannot be directory) Copy of compactflash:/c12k-diags-3.9.0 to disk0:/c12k-diags-3.9.0 is not allowed RP/0/0/CPU0:IOS-XR1# regards tahir
... View more
Labels:
10-07-2012
04:38 PM
thanks sam, Please exaplain me what is Inlet temp 35.5 what is Hotspot temp 61.3 in my case what is recommend Inlet and Hotspot temperature for asr9k regards tahir
... View more
10-07-2012
09:29 AM
hi, what is cisco recommended temperature for ASR 9010 RP/0/RSP0/CPU0:9010#show environment temperatures Sun Oct 7 14:48:34.853 KSA R/S/I Modules Sensor (deg C) 0/0/* host Inlet0 35.5 host Hotspot0 61.3 0/1/* host Inlet0 42.3 host Hotspot0 72.0 0/2/* host Inlet0 41.0 host Hotspot0 78.1 0/RSP0/* host Inlet0 27.7 host Hotspot0 45.6 0/RSP1/* host Inlet0 28.1 host Hotspot0 44.5 RP/0/RSP0/CPU0:9010# Best Regards Tahir
... View more
Labels:
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-07-2012
09:26 AM
10-07-2012
09:26 AM
thanks Nicolas, I will send you by tomorrow..:)
... View more
Created by
Muhammad Tahir Munir
in XR OS and Platforms
in XR OS and Platforms
10-07-2012
07:01 AM
10-07-2012
07:01 AM
Hi, I need help to knw why i am unable to install "asr9k-video-p.pie-4.0.3" package? RP/0/RSP0/CPU0:9010-1(admin)#dir disk0: | in Oct Sun Oct 7 16:50:19.944 KSA 6309 drwx 4096 Sun Oct 7 16:42:32 2012 instdb 10084787 drwx 4096 Sun Oct 7 16:41:23 2012 asr9k-adv-video-supp-4.0.3 5610073 -rwx 600507 Sun Oct 7 19:39:49 2012 asr9k-video-p.pie-4.0.3 5610078 drwx 4096 Sun Oct 7 16:41:28 2012 iosxr-video-adv-4.0.3 RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)#install add disk0:asr9k-video-p.pie-4.0.3 Sun Oct 7 16:50:39.380 KSA Install operation 19 '(admin) install add /disk0:asr9k-video-p.pie-4.0.3' started by user 'admin' via CLI at 16:50:39 KSA Sun Oct 07 2012. The install operation will continue asynchronously. RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)#show install request Sun Oct 7 16:50:46.135 KSA Install operation 19 '(admin) install add /disk0:asr9k-video-p.pie-4.0.3' started by user 'admin' via CLI at 16:50:39 KSA Sun Oct 07 2012. The operation is 1% complete 0KB downloaded: Download in progress The operation cannot be aborted. RP/0/RSP0/CPU0:9010-1(admin)#Error: The install operation failed due to a system error. Please collect diagnostic information using 'show tech-support install' and pass this information to your TAC Error: representative for support. Error: Errors occurred on the following node: Error: 0/RSP1/CPU0 ('install pie get reply' message response reported failure: 'Package Library' detected the 'fatal' condition 'file I/O error': File exists) Install operation 19 failed at 16:50:48 KSA Sun Oct 07 2012. RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)# RP/0/RSP0/CPU0:9010-1(admin)#
... View more
Labels:
10-07-2012
06:00 AM
hi, Few packages are missing one of my remote ASR9010, Please help me how I can copy files from router to other router. TFTP Server Router: RP/0/RSP0/CPU0:ASR9010-1(config)#tftp ipv4 server homedir disk0: TFTP Client: RP/0/RSP0/CPU0:ASR9010-1#copy tftp: disk0: Sun Oct 7 15:42:14.057 KSA Address or name of remote host [10.0.0.5]? Source filename [/tftp:]? Copy operation aborted RP/0/RSP0/CPU0:IDC0100PER02# RP/0/RSP0/CPU0:IDC0100PER02#copy tftp: disk0: Sun Oct 7 15:42:20.710 KSA Address or name of remote host [10.0.0.5]?10.0.0.6 Source filename [/tftp:]?asr9k-video-p-4.0.3 Destination filename [/disk0:/asr9k-video-p-4.0.3]? Copy : Destination exists, overwrite ?[confirm] Accessing t ftp://10.0.0.6/asr9k-video-p-4.0.3 C 320 bytes copied in 0 sec RP/0/RSP0/CPU0:ASR9010-1# RP/0/RSP0/CPU0:ASR9010-1(admin)#copy tftp: disk0: Sun Oct 7 15:54:48.070 KSA Address or name of remote host [10.0.0.6]? Source filename [/tftp:]?asr9k-video-p-4.0.3 Destination filename [/disk0:/asr9k-video-p-4.0.3]? Copy : Destination exists, overwrite ?[confirm] Accessing t ftp://10.0.0.6/asr9k-video-p-4.0.3 C 320 bytes copied in 0 sec RP/0/RSP0/CPU0:ASR9010-1(admin)# RP/0/RSP0/CPU0:ASR9010-1(admin)#install add disk0:asr9k-video-p-4.0.3 Sun Oct 7 15:51:46.629 KSA Install operation 15 '(admin) install add /disk0:asr9k-video-p-4.0.3' started by user 'admin' via CLI at 15:51:46 KSA Sun Oct 07 2012. Error: Cannot proceed with the add operation because the file '/disk0:asr9k-video-p-4.0.3' is not a pie file. Error: Suggested steps to resolve this: Error: - check the name of the pie. Error: - check the location of the pie. Install operation 15 failed at 15:51:47 KSA Sun Oct 07 2012. RP/0/RSP0/CPU0:ASR9010-1(admin)# file size is worng. 10084787 -rwx 320 Sun Oct 7 18:38:56 2012 asr9k-video-p-4.0.3 best regards tahir
... View more
Labels:
Created by
Muhammad Tahir Munir
in XR OS and Platforms
03-01-2013
03-01-2013
hi,1. Install adv video pie.2. Install adv-video-license
(a9k-adv-video-lic is a chassis based licen...
Created by
Muhammad Tahir Munir
in XR OS and Platforms
02-26-2013
02-26-2013
hi,Cisco ASR 9000 Series Per Chassis Advanced Video License.How to
assign to chassis?RegardsMuhammad...
Created by
Muhammad Tahir Munir
in XR OS and Platforms
02-26-2013
02-26-2013
hi,I have asr9k i want to assign video license to slot but i unable to
do anyone help me..:)FeatureI...
Created by
Muhammad Tahir Munir
in XR OS and Platforms
10-09-2012
10-09-2012
Router 1 config
outup:---------------------------------RP/0/RSP0/CPU0:9010-1#sh run int
bundle-ether...
10-08-2012
hi,why this log message keep
appearing??RP/0/RSP0/CPU0:9010-2#RP/0/RSP0/CPU0:9010-2#RP/0/RSP0/CPU0:O...
Created by
Muhammad Tahir Munir
in XR OS and Platforms
10-08-2012
10-08-2012
Please check below output.RP/0/RSP0/CPU0:9010-1#sh install log 19
detaiMon Oct 8 10:56:53.956 KSAIns...
Created by
Muhammad Tahir Munir
in XR OS and Platforms
10-08-2012
10-08-2012
yes workinginstall add compactflash:/c12k-diags-3.9.0 sync
10-07-2012
hi,please help me how i can copy this file c12k-diags-3.9.0 to
disk0:RP/0/0/CPU0:IOS-XR1#dir Sun Oct...
10-07-2012
thanks sam,Please exaplain me what is Inlet temp 35.5 what is Hotspot
temp 61.3 in my case what is r...
10-07-2012
hi,what is cisco recommended temperature for ASR
9010RP/0/RSP0/CPU0:9010#show environment temperatur...
Created by
Muhammad Tahir Munir
in XR OS and Platforms
10-07-2012
10-07-2012
thanks Nicolas,I will send you by tomorrow..:)
Created by
Muhammad Tahir Munir
in XR OS and Platforms
10-07-2012
10-07-2012
Hi,I need help to knw why i am unable to install
"asr9k-video-p.pie-4.0.3" package?RP/0/RSP0/CPU0:90...
Public Statistics
| Date Registered | 01-18-2010 08:17 AM |
| Date Last Visited | 01-26-2019 09:45 PM |
| Total Messages Posted | 19 |
| Total Helpful Votes Received | 10 |
