About RouteOps_gm

RouteOps_gm · 10-23-2024

I'm trying to test a setup in an lab, attempting to peer a multi-homed CPE to a pair of BRAS using PPPoE and BGP. The idea is to use BGP for dynamic route selection and redistribute the routes back into the IGP on the head end.The CPE has a pair of d...

RouteOps_gm · 10-25-2021

Hi all, We are facing an issue where one device (ME3600X) is unable to establish an OSPF adjacency with its neighbours. It connects to the other OSPF peers via a /29 network with OSPF in broadcast mode. The other peers within the /29 are able to peer...

RouteOps_gm · 05-27-2021

Hi,I have a site to site VPN configured between two ASA 5508X's. There is network (subnet) on site A and three networks on site B. Phases 1 & 2 come up no problem and I can ping across the tunnel for 2 of the 3 networks. With the third network, if I ...

RouteOps_gm · 05-03-2016

I am trying to make sense of the changes that Cisco has made to NAT on ASA > v8.3. I have a network which is being PAT'd to the outside interface address, and want to add a static NAT from the outside interface IP to a specific inside host. Relevant ...

RouteOps_gm · 04-26-2016

Hi, I am facing a problem with a Nexus 3064PQ switch where I am trying to configure a management VLAN, which I can use to administer the switch. I am unable to use the management port on the back of the device as the incoming circuits to the rack ar...

RouteOps_gm · 10-23-2024

Thanks Flavio that's super helpful, and you're right on the money.The problem was that I had ebgp-multihop configured on the client but not in the BGP config on the LNS. Added the following and BGP came straight up:neighbor PPP-CLIENTS ebgp-multihop ...

RouteOps_gm · 12-09-2021

I only just applied the dialer watch-list config as mentioned in the posts above, but my Cellular 0/2/0 interface came straight up when I did. I have a default route via Cellular0/2/0 so the IP being watched is in the routing table. Time will tell wh...

RouteOps_gm · 10-27-2021

To anyone else facing the same issue, I managed to solve this in the end. The issue appeared to have been the result of a software bug. I checked (far too late in the process!) the image on the box and found it to be a very old version 15.4-1.S1. I u...

RouteOps_gm · 10-25-2021

Here's the output from debug ip ospf adj - I copied quite a bit to capture all the important info. The peer seems to be working and then is declared dead, I can't see any obvious reason in the log but maybe someone more knowledgeable will:Oct 25 19:4...

RouteOps_gm · 10-25-2021

@Georg Pauwen wrote:in your original post, it sounded you had one Meraki device mixed with other devices:Sorry for the confusion - ME3600X is a Cisco metro Ethernet layer 3 switch @Georg Pauwen wrote:Either way, try and configure Loopback IP address...

Member Since	‎09-15-2011 10:40 AM
Date Last Visited	‎10-24-2024 01:37 AM
Posts	24
Total Helpful Votes Received	16

User Statistics

User Activity

Struggling with BGP over PPPoE

Repeatedly logging %OSPF-5-ADJCHG from LOADING to DOWN

ASA return traffic not matching site to site cryptomap

Unable to configure ASA PAT with static NAT on v8.3+

Nexus 3064PQ unable to configure management VLAN

Re: Struggling with BGP over PPPoE

Re: C1112-8PLTEEA LTE Config / %Remove Legacy DDR Configuration first

Re: Repeatedly logging %OSPF-5-ADJCHG from LOADING to DOWN

Re: Repeatedly logging %OSPF-5-ADJCHG from LOADING to DOWN

Re: Repeatedly logging %OSPF-5-ADJCHG from LOADING to DOWN