About banavathkiran

banavathkiran · 03-14-2014

Hi, I have 100Mbps Internet Bandwidth connection. when I Perform speedIn wired-- >100 MbpsIn wireless client--> 20 mbpsAccess points used is Autonomous N-series access point. whcih has to support upto 300 Mbps.I have done iperf testing also.There als...

banavathkiran · 10-07-2013

In my LAN Network, 3750 core and 2960 access switches, in the same VLAN communication the latency is 1ms most of the time in the middle till raise to 2ms to 23 ms.Why this happens? In the same switch connected PC as getting more latency.

banavathkiran · 08-27-2013

Hi,We've been struggling with this problem for weeks without a solution yet. Maybe someone can help us. we have radius sever over WAN with PEAP configuration. These days I could see this traps logs offen and clients are unable to connect. I have tri...

banavathkiran · 08-21-2013

Hi all,I have a doubt, My wireless client card is 1x1 11b/g/nWireless LAN PCI Express Half Mini Card Adapter which has only 1X1 spatial stearms, But as far I know 802.11n (which gives greater bandwidth upto 150 mbps in 2.4Ghz and 300 & 450 Mbps in 5g...

banavathkiran · 08-05-2013

I have two radius servers configured in cisco wlc 2504, few users are unable to authenticate and connect to WLAN. For some uses Im getting these logs71 Mon Aug 5 12:54:58 2013 RADIUS server 172.16.100.254:1812 failed to respond to request (ID 208) fo...

banavathkiran · 03-14-2014

40MHz is enabled on the cisco 1600 access point. But we are unable to get that throughtput atleast 50 mbps in 5 Ghz.Only one client is connected to Access point.we are facing the same issue with controller based AP. we are testing in idle conditions,...

banavathkiran · 03-14-2014

Hi, I can see in the WLAN client status showing 300 mbps. But when I test the throughput it is attaining only 20 to 25 mbps. why?I have testing this with Lwapp AP and Autonomous AP also.

banavathkiran · 08-28-2013

Before there are two radius servers configured for WLAN as primary and secondary. As there was some problem with primary radius sever. I have disabled the primary radius server in my WLC. Now, it is operating only on single radius server. tell me one...

banavathkiran · 08-28-2013

Thanks Mohammad,I concered is more about the radius server is not responding to the request of client mac address./ user "unknow". This happend 2 weeks back also, later we came to know that the primary radius ACS running 5.3 services are hanged. So I...

banavathkiran · 08-28-2013

1.we are not using the any HREAP Mode access points, All are in local mode only.2. Radius server is located at different location.3. Client authenticate via AD4. Cisco ACS is our radius server5. No changes are made in WLC, as well as in ACS. Only the...

Member Since	‎03-20-2013 08:04 AM
Date Last Visited	‎08-18-2017 04:27 AM
Posts	20

User Statistics

User Activity

What is the Maximum thoughput attained by WLAN Client ?

How to eleminate the latency and make it equal to <1 or =1ms

Radius authntication failure

How does client wireless card with 1x1 spatial steam support 802.11 n ?

Suddenly few users are not authenticating through AAA

40MHz is enabled on the cisco

Hi, I can see in the WLAN

Radius authntication failure

Re: Radius authntication failure

Radius authntication failure