Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About jwornstaff
05-03-2019
jwornstaff
Member since
11-03-2004
Beginner
04-11-2019
10:39 AM
Yep, I found that as well. The other issue is the config guides doesn't provide the procedure for an air gap system or offline registration other than the satellite method, which still doesn't work in my case. I think i figure out how to do, but then run into another issue where I'm trying to register/activate a C9300-24T and the license file that they dumped in my smart account is for a C9300-24P, and I keep getting no available licenses and the license dept just giving me the run around after the license was missing in action for a couple weeks they manually inputted but itsthe wrong product type...I got 14 new 4451x and 20 some switches arriving and about to loose my mind just dealing with one.
... View more
04-11-2019
07:38 AM
Thanks for the info, I'm familiar with the right to use, but there lies another problem, there is no license right-to-use commands, only license smart. They switch came with 16.9.2 loaded, so I guess I'llgo glean through the release notes again and see if there is anything new. This crap is frustrating....
... View more
04-11-2019
05:30 AM
So I received my first CAT 93000 in prep for upcoming recap this year. It's a C9300-24T with Network Essentials and DNA Essentials. My issue is that both the Network Essentials and DNA Essentials license is showing to be running in "EVAL" mode. I'm new to the whole smart licensing thing, but I have Smart License account and would have assumed the DNA required Smart License activation but not the network essentials. I would have though that the base license would be perpetual from the factory since this is the switch type we bought. My question is this normal, that is do both license need to be activated/registered right out of the box? Or should the switch come with at least the base license activated?? Also, this is an air gap system, so no internet connection for call-home registration. I have some make shift procedure for doing the manual registration via the smart license portal but my second issue is that Cisco never dumped any license into my smart account for out purchases, so nothing there to register against. My Cisco reps are looking to the missing license but haven't explained the why network essentials is not registered from the factory. This process is way too time consuming and confusing when you have 100s of devices to roll out.....
... View more
Labels:
Created by
jwornstaff
in IP Telephony and Phones
in IP Telephony and Phones
03-20-2019
09:32 AM
03-20-2019
09:32 AM
Problem ended up being with dial-peer on Main Site router back to remote router.
Called Number=3331000(TON=Unknown, NPI=Unknown),
Calling Translated=FALSE, Subscriber Type Str=Unknown, FinalDestinationFlag=TRUE,
Incoming Dial-peer=0
Whereby, the remote CME router has a dialplan pattern that changes the internal prefix to match the external POTs area code and prefix. The Main Site router did not no how to route the call, as the incoming/out going dial-peer was set to the local prefix.
I added the incoming called-number . to the dial peer facing the remoter router and all works.
What I'm not sure of is why this worked for SCCP related calls and not SIP calls.
... View more
Created by
jwornstaff
in IP Telephony and Phones
in IP Telephony and Phones
03-19-2019
11:08 AM
03-19-2019
11:08 AM
And what would be my order of preference? It's hardcoded on the outbound dial-peers as well.
... View more
Created by
jwornstaff
in IP Telephony and Phones
in IP Telephony and Phones
03-19-2019
06:06 AM
03-19-2019
06:06 AM
I am attempting to upgrade VOIP phones from 7942/7962s all running SCCP on my CME routers. I have installed one SIP 8811 voip phone at our main site and have configured voice service on main CME router. The SIP phone can call all local SCCP phones and all local SCCP phones can call the new SIP phone. The new SIP phone can place a call to the remote site CME SCCP phone, however when the remote SCCP (multiple phones) try to call the new SIP it rings but when you pick up the handset the call is quickly disconnected.
The path looks like this: SCCP phone > CME > WAN (OCONUS 220ms delay) > CME > SIP and then back the same way.
I’m not voice expert by no means, and acquired this this system already built, but did see in the trace logs a “Disconnect Cause 65”
I have played with DTMF relay, codec hard coding, no coding, etc to nothing seems to work.
Below are the snipits of affected router configs. Routers are running IOS 15.6.3(M4) on all.
7962/7942 are running SCCP version 9-3-1-57 and in some 8-5 and 8811 is running sip88xx11-5-1-18
Remote Site 2 CME router Configs with all SCCP phones:
gatekeeper
shutdown
!
!
telephony-service
max-ephones 19
max-dn 23
ip source-address 20.0.2.3 port 2000 secondary 20.0.2.4
service phone webAccess 0
timeouts interdigit 5
cnf-file location flash:
load 7942 SCCP42.9-3-1SR1-1S
dialplan-pattern 1 703378.... extension-length 7 extension-pattern 222....
max-conferences 12 gain -6
transfer-system full-consult
transfer-pattern .T
secondary-dialtone 9
after-hours block pattern 1 9 7-24
after-hours block pattern 2 555 7-24
after-hours block pattern 3 777 7-24
voice service voip
no ip address trusted authenticate
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
dial-peer voice 333 voip
destination-pattern 333....
session target ipv4:30.0.2.1
dtmf-relay h245-alphanumeric h245-signal
codec g711ulaw
ephone-dn 1
number 2224173
description Room 1/Jack #5
ephone-dn 21
number 2220101
description S02 interior phones
ephone 1
no multicast-moh
device-security-mode none
description Room 1/Jack #5 (x-9351)
mac-address 0023.EB53.FB94
after-hours exempt
button 1:1 2:21
Main site 3 CME router sp3nrtr01 with SIP and SCP phones:
telephony-service
max-ephones 4
max-dn 4
ip source-address 30.0.2.3 port 2000 secondary 30.0.2.4
service phone webAccess 0
cnf-file location flash:
load 7942 SCCP42.9-3-1SR1-1S
dialplan-pattern 1 703378.... extension-length 7 extension-pattern 333....
max-conferences 12 gain -6
transfer-system full-consult
voice service voip
no ip address trusted authenticate
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
registrar server expires max 600 min 60
dial-peer voice 222 voip
destination-pattern 222....
session target ipv4:20.0.2.1
dtmf-relay h245-alphanumeric h245-signal
codec g711ulaw
ephone-dn 4
number 3330100
description S03 All phones
shared-line sip
voice register global
mode cme
source-address 30.0.2.3 port 5060
max-dn 100
max-pool 100
authenticate realm al
timezone 21
tftp-path flash:
create profile sync 6343063011385032
ntp-server 30.0.1.1 mode directedbroadcast
auto-register
!
voice register dn 31
number 3331000
name SP3NPHN01
label S3 Conf RM
!
voice register dn 34
number 3330100
allow watch
shared-line max-calls 16
label S3 All Phones
!
voice register template 1
!
voice register pool 1
id mac 006C.BCBD.66E0
type 8811
number 1 dn 31
number 2 dn 34
dtmf-relay sip-notify
username cisco2 password cisco2
codec g711ulaw
no vad
... View more
10-17-2018
04:27 AM
So I'm attempting to use the IOS to XE convertor tool, and having difficult time understanding the output results and why some lines are showing "Unprocessed" . I have like 191 lines showing "unprocessed" with pretty basic commands, that don't make sense to me, what is it trying to tell me.
Example:
Unchanged tunnel interface commands
335 interface Tunnel371
336 description Tunnel 371 (via DS3) to SP7NRTR01 (10.0.2.46)
337 ip address 10.0.x.x 255.255.255.252
338 ip mtu 1399
------------------------- Then remaining tunnel config show unprocessed...why?
!ip wccp password xxxxxxxxx
340 !ip hold-time eigrp 10 45
341 !ip flow ingress
342 !ip tcp adjust-mss 1359
343 !load-interval 30
344 !delay 1000
345 !qos pre-classify
346 !keepalive 10 3
347 !cdp enable
348 !tunnel source 10.0.x.x
349 !tunnel destination 10.0.x.x
350 !tunnel path-mtu-discovery
Other notable lines indicating "unprocessed"
vlan 30
--------------
ip vrf xx
rd 1:1
------
standby 1
---------
connection plar 2221111
---------
privilege exec level
-----------------
crypto map
... View more
Labels:
Created by
jwornstaff
in IP Telephony and Phones
in IP Telephony and Phones
05-21-2018
11:32 AM
05-21-2018
11:32 AM
I know this thread is quite old but hoping someone still around to answer a few questions. I have tried the above mentioned commands to disable the speaker phone on global bases and per phone, and can not get it to work. These are older 7942 and 7962 phones running like firmware 9.3.3 with CME on the router. I do have an error on the phone status message that gives error retrieving SEPxxxx.xml.cnf file. So am I suppose to be serving that file up on the router tftp server or how does it know where and what file to retrieve.
... View more
Created by
jwornstaff
in Network Management
in Network Management
02-27-2018
11:02 AM
02-27-2018
11:02 AM
I'm trying to use the Cisco Prime 3.2 Configuration Templates in the Features & Technologies-Security-VPN Components-Pre-shared keys to change existing pre-share keys on multipule IPsec/GRE Tunnels.
I add the peer IP and subnet mask, then it ask for the pre-share key twice. When I type the pre-share in, it does not show up, however I then save and when I look at the CLI commands that will be deployed, it shows a "NO" for the exiting pre-share keys and peers, and then the new one but with all ***** (asterix) I deploy anyway, however the key just shows up as * (asterix) in the router's configuration, and even though I match the key on both sides, when I clear the security associates the tunnel breaks.
I am assuming that from within Cisco Prime the pre-share key I enter is not getting encrypted correctly or at all either before or after I deploy to the router.
Anyone have any ideas or experience with this to make it work. Is Cisco Prime expecting that I am enter an already existing encrypted pre-share or is it suppose to except clear text key and encrypted it or let the router encrypt it?
... View more
Labels:
Created by
jwornstaff
in Network Management
in Network Management
09-14-2017
08:39 AM
09-14-2017
08:39 AM
Thanks for the info and reassurance. I wasn't sure if anyone would get what I was trying to say/ask. Cisco never seems to make it easy. It's easy if it works as advertise but if it goes wrong theny you are screwed trying to rebuild. Had this happen with a WAAS Central Manager appliance, inline did not work and wiped the the database, ended up rebuilding from scratch. But back to the VM clone, I was wondering if a clone or snapshot would function correctly, if brought up as live version if primary server got hosed up during upgrade....did you have any issues with license, database, etc?
... View more
Created by
jwornstaff
in Network Management
in Network Management
09-14-2017
04:30 AM
09-14-2017
04:30 AM
I'm looking to upgrade our primary standalone Prime server 3.1 to 3.2. In reading the release notes they indicate an inline upgrade is possible, however it goes through the instructions of backing up current 3.1 server and moving the backups to remote storage, etc, etc. However if you read the the 3.2 Guides on backups and restores, it says that 3.1 backups can not be applied to the 3.2 virtual or physical appliances. So what the heck is the point in backing the operational 3.1 server if I can't reapply or restore to 3.2, if that is truely the case. And does the inline upgrade wipe the the current 3.1 server configs or does it preform the migration/converstion automatically so that a restore of the old data is not neccessary required, unless it would happen to fail? And what happens if the 3.1 to 3.2 inline upgrade goes wrong and how can I restore the backups? Anyone have any insight, previous experience, thoughts?
... View more
Labels:
04-19-2017
09:12 AM
Just this one out of 6 in this particular network.
Going to try reload, but have to wait several weeks for maintenance window.
... View more
04-19-2017
07:22 AM
I already have that set. This router/sw module has been functioning with same config since last recap a couple years ago. So nothing really changed, accept a recent trunk port brought up to an external (outside our domain) who is apparently doing a L2 pseudo wire connection to us. But I also shutdown that link and still receiving the error.
... View more
04-19-2017
06:28 AM
Been receiving the following syslog messages on a 3945 ISR and have no idea what it is referring to and can't find one scrap of information on the syslog message.
Apr 19 12:50:42.471: logTIME1: mismatch 16 18 55970 <--> 16 18 55969 Apr 19 12:51:12.466: logTIME1: mismatch 16 18 55971 <--> 16 18 55970 Apr 19 12:51:42.470: logTIME1: mismatch 16 18 55972 <--> 16 18 55971
As you can see the appear about every 30sec and the last couple of numbers escalate.
I thought orginal it was NTP related but I removed NTP settings and they still reappear. I re-configure NTP and resync and both system time and NTP time are correct.
Any ideas??
Thanks!
... View more
- Tags:
- sylog
Labels:
12-22-2016
08:34 AM
I know this post is old but in the event you or any one else is looking for an answer, I found a manual work around and/or solution in my case.
If you have Netflow enable on your Network devices and exporting it to prime.
Navigate to Services > Application Visibility & Control > Data Sources
From the Data Sources window you will see list of devices that are exporting Netflow to Prime. If you know at least the source router for the unknown traffic, you can do the following.
Click the "I" or information icon next to the Data Source, then check the box for the "Raw Report"
Now, click the Netflow hyperlink in the Netflow Template column. this will open the Netflow Templates window, click the "Launch Report" hyper link in the upper right corner.
A new Netflow Report is opened, click the DataSource for the router or network device, select a time period, report title, etc, then click run and/or you can save the report as new template.
The Report Run Results will be displayed in the next window and you will have a full view of the raw traffic including source destination IPs and Ports.
Now, this will at least give you view of the traffic, but you will still have to determine the unknown traffic but it easily down by correlating source and destination IPs, time frames, etc and or just by know the applications and traffic on your network.
You can then go to Services > Application Visibility & Control > Application and Services and create and add the unknown ports, and/or services.
Not a perfect answer or solution but it helped identify and label most of our custom apps and traffic not known by Prime.
... View more
04-11-2019 10:39 AM
Yep, I found that as well. The other issue is the config guides doesn't
provide the procedure for an...
04-11-2019 07:38 AM
Thanks for the info, I'm familiar with the right to use, but there lies
another problem, there is no...
04-11-2019 05:30 AM
So I received my first CAT 93000 in prep for upcoming recap this year.
It's a C9300-24T with Network...
Created by
jwornstaff
in IP Telephony and Phones
03-20-2019 09:32 AM
03-20-2019 09:32 AM
Problem ended up being with dial-peer on Main Site router back to remote
router. Called Number=33310...
Created by
jwornstaff
in IP Telephony and Phones
03-19-2019 11:08 AM
03-19-2019 11:08 AM
And what would be my order of preference? It's hardcoded on the outbound
dial-peers as well.
Created by
jwornstaff
in IP Telephony and Phones
03-19-2019 06:06 AM
03-19-2019 06:06 AM
I am attempting to upgrade VOIP phones from 7942/7962s all running SCCP
on my CME routers. I have in...
10-17-2018 04:27 AM
So I'm attempting to use the IOS to XE convertor tool, and having
difficult time understanding the o...
Created by
jwornstaff
in IP Telephony and Phones
05-21-2018 11:32 AM
05-21-2018 11:32 AM
I know this thread is quite old but hoping someone still around to
answer a few questions. I have tr...
Created by
jwornstaff
in Network Management
02-27-2018 11:02 AM
02-27-2018 11:02 AM
I'm trying to use the Cisco Prime 3.2 Configuration Templates in the
Features & Technologies-Securit...
Created by
jwornstaff
in Network Management
09-14-2017 08:39 AM
09-14-2017 08:39 AM
Thanks for the info and reassurance. I wasn't sure if anyone would get
what I was trying to say/ask....
Created by
jwornstaff
in Network Management
09-14-2017 04:30 AM
09-14-2017 04:30 AM
I'm looking to upgrade our primary standalone Prime server 3.1 to 3.2.
In reading the release notes ...
06-26-2017 04:07 AM
In my case neither rebooting or upgrading fixed the problem, had to open
TAC case and they new exact...
05-03-2017 10:17 AM
I had multiple issues including the one you mentioned when upgrading
from 6.0 to 6.1 that I lost tra...
04-27-2017 04:38 AM
Did you ever get this resolved? I getting same error after upgrading
from 6.0.x to 6.1.x.
Public Statistics
| Date Registered | 11-03-2004 09:10 AM |
| Date Last Visited | 05-03-2019 01:42 AM |
| Total Messages Posted | 37 |
| Total Helpful Votes Received | 28 |
Helpful Votes Given To
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
Helpful Votes From
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 3 |
