Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About moman62
Online
moman62
Member since
04-29-2018
Beginner
07-20-2019
08:11 AM
My internet is Spectrum Business cable formerly known as TimeWarner Business cable
... View more
07-19-2019
07:00 PM
Hello, I have a Cisco 2921 router IOS 15.07 and I wanted to know if I could connect my Netgear Wireless router to it so that I could configure the Netgear as an Access Point? The Netgear wireless router has a section where it can be configured as an AP. Would I need a wireless module? and what kind would be compatible? My netgear is wireless with 2.4 and 5g channels.
... View more
Labels:
07-18-2019
09:13 AM
I would like to know was which would be better since I have CME 12.0. The ISM module which I will purchase? or the PVDM3 which is already installed with the router which is using IOS 15.7M and also which version of Cisco Unity would work for this possible setup? I already have a SIP setup from my vendor, Just trying to decide which route to go.
... View more
07-18-2019
07:05 AM
Hello, I am trying to decide which is better to use, I have a cisco 2921 router that has a PVDM3-32, My IOS is 15.7M and I wanted to know which would be better the PVDM3 or ISM-SRE-300-K9 module? I also have CME 12.0. This will also be using Unity for voicemail.
... View more
Labels:
06-04-2019
11:06 PM
Ok, so I would have to purchase the software from the reseller as well?
... View more
06-04-2019
06:19 PM
Hello, I am seeking some information because I'm about to purchase some CUCM licenses from a cisco certified vendor for (5) phones and wanted to know that once I purchase the licenses, would I be able to download the CUCM software to use in a live environment?
... View more
Labels:
10-26-2018
10:59 AM
None of the options worked since on a Cisco 2811 router vlan database is deprecated. What I did was purchase an hwic -1FE card and configured it with a different ip address so that it would not interfere with my fa0/1. And I was able to configure ssh etc to login remotely which is what I wanted to do and not create a vlans or svi connection.
... View more
10-18-2018
08:10 PM
I was not using the module at all until today. I wanted to use the module port fa0/2/0 as a way to set an ip address and configure for remote ssh via putty so I would not have to use my console cable all the time.
But from what I'm hearing it cannot be configured unless its eitther vlan or svi configured.
I just really want to know what name/model of module would I need just for the purpose of remoting into the 2811 router? I don't want to configure a virtual or switch port just to do that.
... View more
10-18-2018
06:35 PM
So basically if you are using Fa0/0 and Fa0/1 for the internet without the modules, you have no way of telnet or ssh into the 2811 router?
But if you have the module, you have to create vlans or svi to telnet or ssh into the router?
... View more
10-18-2018
04:31 PM
Is there a module that will work with the router that supports layer 3? I mean I could use vlans but I'm looking to be able to ssh into the router for remote config instead of using the console cable all of the time?
... View more
10-18-2018
03:04 PM
message after no switchport command:
RT1LAB(config)#int FastEthernet0/2/0 RT1LAB(config-if)#no switchport Command rejected: Not a convertable port. RT1LAB(config-if)#
I am using an HWIC -4ES FastEthernet module, Is there an add-on module that does work for this router? Thanks
... View more
10-18-2018
02:08 PM
I am using a cisco 2811 router that has the fa0/0 and 0/1 ports configured for internet.
I am trying to config int fa0/2/0 which is an add-on card for network connectivity and when I try to give the port an ip address, this is the message I get:
RT1LAB(config)#int fa0/2/0
RT1LAB(config-if)#ip address 192.168.1.62 255.255.255.0
% IP addresses may not be configured on L2 links.
What does that mean? Thanks
... View more
Labels:
10-17-2018
10:48 AM
I was able to TFTP my configs to my pc by enabling windows 10 firewall rules and adding the udp port. I have copied/paste the link for anyone else who is having issues with TFTP'ng from their cisco appliance to their pc etc.
https://www.youtube.com/watch?v=hsPtoDxn01I
... View more
10-17-2018
07:07 AM
I have the firmware!! I'm trying to backup the firmware on my cisco 2811 router using tftp server and that is the error I'm getting.
... View more
yesterday
Hello, I have a Cisco 2921 router IOS 15.07 and I wanted to know if I
could connect my Netgear Wirel...
Thursday
I would like to know was which would be better since I have CME 12.0.
The ISM module which I will pu...
Thursday
Hello, I am trying to decide which is better to use, I have a cisco 2921
router that has a PVDM3-32,...
06-04-2019 06:19 PM
Hello, I am seeking some information because I'm about to purchase some
CUCM licenses from a cisco c...
10-26-2018 10:59 AM
None of the options worked since on a Cisco 2811 router vlan database is
deprecated. What I did was ...
10-18-2018 08:10 PM
I was not using the module at all until today. I wanted to use the
module port fa0/2/0 as a way to s...
10-18-2018 06:35 PM
So basically if you are using Fa0/0 and Fa0/1 for the internet without
the modules, you have no way ...
10-18-2018 04:31 PM
Is there a module that will work with the router that supports layer 3?
I mean I could use vlans but...
10-18-2018 03:04 PM
message after no switchport command: RT1LAB(config)#int
FastEthernet0/2/0 RT1LAB(config-if)#no switc...
10-18-2018 02:08 PM
I am using a cisco 2811 router that has the fa0/0 and 0/1 ports
configured for internet. I am trying...
10-17-2018 10:48 AM
I was able to TFTP my configs to my pc by enabling windows 10 firewall
rules and adding the udp port...
Public Statistics
| Date Registered | 04-29-2018 10:27 PM |
| Date Last Visited | 07-20-2019 02:55 PM |
| Total Messages Posted | 34 |
| Total Helpful Votes Received | 5 |
.jpg "VIP Expert"){kind=icon}
