About CSCO10892433

CSCO10892433 · 03-21-2008

Ping frome r1:r1#ping 10.100.12.2 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.100.12.2, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 4/7/8 msr1#and show access-list on r2:r2#sh ac...

CSCO10892433 · 02-02-2008

Hello everyoneI was trying to install this card into the NM-HDV as well as the wic slot of a 2621xm, but always got the following error message:%E1T1_MODULE-3-INITFAILURE: Slot 1, Unit 0 initialization failure - Firmware Download%E1T1_MODULE-3-INITFA...

CSCO10892433 · 08-03-2007

Hi, forumBased on the following link:http://www.cisco.com/en/US/products/sw/iosswrel/ps1829/products_feature_guide09186a008056c866.htmlI was doing a lab test for this new feature. The lab senario is very simple, R1 send 10.1.1.0/24 to R2, R2 will con...

CSCO10892433 · 06-09-2007

Hi, forumThis senario comes form Routing TCP/IP volume 2, page 298. When I finished configuring all 8 routers, I have the following output form the router named Whitetooth:r6#sh ip bgp 10.35.5.0BGP routing table entry for 10.35.5.0/24, version 14Path...

CSCO10892433 · 03-24-2008

Hi, RickI just finish the lab round 4, but I found more wierd thing: if I add the log keyword to the and of each acl entry, I got only 5 matches!!!Without the log keyword, I got 15 matches as usual. How do you explain this?BRSSLINPS: This time I'm ve...

CSCO10892433 · 03-24-2008

Hi,You are connecting to the AUX port. Please change it to the console port. The console pot is next to the AUX port. See:http://www.cisco.com/en/US/products/hw/routers/ps259/products_installation_guide_chapter09186a008007e1f8.html#xtocid11HTHSSLIN

CSCO10892433 · 03-23-2008

Hi, RickSorry for the inconsistency among the several labs I did. I change the routers and the interfaces because I want to see if there is any difference. I'm sure I was pinging from the other router, not my own router. I will do the lab this night ...

CSCO10892433 · 03-23-2008

Hi, michaelThere is a free version of tacacs+ for linux on cisco ftp site:ftp://ftp-eng.cisco.com/pub/tacacs/username:anonymouspassword:your email addressIt surely support command audit (or it won't be called AAA), but not sure about the integration ...

CSCO10892433 · 03-23-2008

Hi, kevin, rickThank both of you for the concerns about this topic.Here is the result of acl-lab-round-3 (see attachment)and it is same as before. I also attach the running-config that I don't see any other place the ACL is applied. Please check it f...

Member Since	‎02-10-2005 11:40 PM
Date Last Visited	‎08-18-2017 03:53 AM
Posts	313
Total Helpful Votes Received	138

User Statistics

User Activity

access-list matches are 3 times as much as packets received, why?

vwic-1mft-t1 doesn't work, need help

BGP Conditional Route Injection doesn't work, need help.

BGP confederation lab question

Re: access-list matches are 3 times as much as packets received,

Re: Set password for cisco 2600

Re: access-list matches are 3 times as much as packets received,

Re: TACACS+ Question

Re: access-list matches are 3 times as much as packets received,