About inderpalsogi

inderpalsogi · 12-31-2013

We currently have the following scenario with 2 ipsec vpn tunnels setup.inside LAN = 172.20.136.0/24Remote Site1 internal LAN = 192.168.1.0/24Remote Site2 internal LAN = 192.168.2.0/24The VPN tunnels establish without any issues and I can connect to ...

inderpalsogi · 08-27-2013

I have a number of public IP addresses, one which has been assigned to the outside interface of an ASA 5505.What I am trying to achieve is use a 2nd public address as the LAN to LAN VPN termination address.Now I know you can terminate VPNs on the out...

inderpalsogi · 07-11-2012

We recently replaced a 5596 due to an issue with SFP modules not being recognised on 1 port. We took the config off the old 5596 and put it onto the new one.2 x 5596 nexus switches are connected together with one port being used a the peer keeaplive...

inderpalsogi · 01-11-2012

'm trying to set up a vpn connection through two ASA 5510 firewalls. My network is as follows:PC | FW A | Internet |FW B| - lan |I am trying to achieve the following: PC | FW A | Internet |FW B| - | DMZ | - | FW C| - | lan |However, I am not sure wh...

inderpalsogi · 03-02-2009

I am having an issue with telnetting to a Cisco router from an IPsec VPN created between a Cisco 857 and a Draytek router. I can telnet to and ping the draytek router from the Cisco LAN, however from the LAN behind the draytek, I cannot telnet to th...

inderpalsogi · 02-22-2017

Hi Alexander, Can you please confirm how you did this on 6.2 as I am having issues pinging the IP addresses of interfaces configured. Looking at the CLI, it already has an inspect ICMP but this is not working. How did you create the variable ICMP? Yo...

inderpalsogi · 02-18-2016

Hi, Please can you elaborate on this. If you have both interfaces enabled for IPSEC access, then the crypto maps that are created get automatically assigned to those interfaces so there is no need to duplicate them. If you delete one of the two id...

inderpalsogi · 12-31-2013

Sorry my original statements should have read as: - static (out,in) 172.23.0.1 192.168.1.10 netmask 255.255.255.255static (out,in) 172.23.1.2 192.168.2.10 netmask 255.255.255.255As it is 182.168.1.x on the outside and 17.23.0.1 or 1.2 on the inside.

inderpalsogi · 12-17-2013

I had this issue but managed to resolve it.The issue was with bind authenticate root-dn CN=,CN=Users,DC=mydomain,DC=com password The is the Display Name i.e. (FirstName and Last Name) of the user in AD, and this has to have NO SPACES. For example I...

inderpalsogi · 08-27-2013

Thanks Karsten.This is not RAS clients, these are LAN to LAN IPsec VPN tunnels.

Member Since	‎03-08-2007 08:57 AM
Date Last Visited	‎06-12-2018 05:59 PM
Posts	35
Total Helpful Votes Received	5

User Statistics

User Activity

Destination NAT over IPSEC VPN on ASA

Multiple Public IP addresses on Outside

Nexus 5596 spanning-tree config issue

help with setting up VPN through 2 ASA 5510 Firewalls

Telnet Problem with IOS IPsec VPN

Hi Alexander,

Hi,

Destination NAT over IPSEC VPN on ASA

Scansafe ldap resultCode: 49 Invalid Credentials. Default usergr

Multiple Public IP addresses on Outside