About shinwoo_acdc77

shinwoo_acdc77 · ‎07-08-2012

why different L2, L3 interface's input queue depth on same module ? 1. switchcport mode access Port input queue : 0/2000/0/0 2. no switchport Port input queue : 0/75/0/0 please help ME !!!!!!!!!

shinwoo_acdc77 · ‎05-19-2010

thanks your reply.. Yes.. under 144M... why not display 300Mbps ? notebook is ThinkPad X300... good PC... i dont understand..

shinwoo_acdc77 · ‎05-19-2010

why 144M on 1142 802.11N? 1142 configuration dot11 ssid WPA2 authentication open authentication key-management wpa version 2 guest-mode wpa-psk ascii 7 03550958525A771B165049 interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid WPA2 ! antenna gain 0 no dfs band block channel width 40-above channel 5745 i dont understand AP's speed... please help..

shinwoo_acdc77 · ‎03-29-2010

thank you... your reply.... AP is enough.....and Client Driver all Update I think that auto-AP NO RRM fuction.. but LAP RRM fuction enable Channel Interference may give rise to Client Roaming..although Channel & Power is fix I set-up more less tight Performance profile on Controller (Cisco recommand : Controller very tight) I attach channel analyze report result although Performance profile change more less tight on LAP environment I think that controller base wireless inconsistence on heavy Channel Interference environment thank you..!! please reply

shinwoo_acdc77 · ‎03-29-2010

sorry!! i'm very busy...^^ our all Client driver update, AP connect Radius(ACS) all fine..

shinwoo_acdc77 · ‎03-23-2010

hi. this is kim i have some questions!!! please help my customer use wireless network (controller based). WLC 4404(4.2.130) + LAP(1131) + WPA1(TKIP) + Radius(ACS4.1)+HREAP some client disconnect frequently, so we update client wireless driver, and change channel & power ,WLC RRM fix so we change LAP to Autonomous AP, all fine.. why? i dont understand....why client disconnect? please help!!!!

shinwoo_acdc77 · ‎08-17-2009

install hardware WLC ACS AP1131 WPA1+TKIP, H-REAP Client high frequently reconnect(roaming in APs), i think WLC RRM Problem ..I attack WCS log please help me.. all WLC is same RF group... (no need roaming)

shinwoo_acdc77 · ‎03-23-2008

FWSM cpu high level (90%-100%) by periods.. I think bug on 3.2(3) but not certainly I found bug 1. tcp-normalizer 2. High CPU in http inspection add "show process" file (normal,problem) please help me..

shinwoo_acdc77 · ‎02-29-2008

hi my name is kim.. i had installed FWSM3.2(3)+SUP720 traffic is 1Gbps(in+out) but i founded FWSM abnormal condition[symptom high CPU normal 40~50 % bug? or misconfig? please reply to me

shinwoo_acdc77 · ‎05-31-2007

topology real server : 2 contents configuration owner test content web_service add service server1 add service server2 vip address 172.25.1.1 port 80 protocol tcp advanced-balance sticky-srcip-dstport active slb not work!!! CSS11503# sh service summary Service Name State Conn Weight Avg State Load Transitions server1 Alive 12 1 56 100 server2 Alive 0 1 2 84 conn problem.. why.. please help

shinwoo_acdc77 · ‎05-13-2007

help me.. topology outside | ASA5520__ | | inside1 inside2 | | HUB relate log : pix deny TCP (no connection) flag RST on interface inside i expect problem because two inside interface connected same HUB or switch help me..

shinwoo_acdc77 · ‎05-10-2007

why not nat translation ... i don't understand.. please help me ==== config ==== nat (inside1) 1 10.10.10.0 255.255.255.0 nat (inside2) 1 10.10.11.0 255.255.255.0 global (outside) 1 192.168.1.1-192.168.1.100 some PC not connect to outside network error message : portmap translation creation failed asa or pix bug?

shinwoo_acdc77 · ‎10-16-2006

hi.. my name is Kimshinwoo.. i will question DMVPN SA problem.. topology DMVPN HUB Router tunnel1(source Fa0/0) tunnel2(source Fa0/0) DMVPN SPOKE Router tunnel1(source fa0/0) tunnel2(source fa0/1) SPOKE router have 2 physical interface.. and 2 tunnel interface... but HUB router have 1 physical interface.. and 2 tunnel interface... i want connect ipsec tunnel between HUB and SPOKE... but only one Tunnel connection.. i expect SA problem.. please help me...

shinwoo_acdc77 · ‎10-09-2006

hi.. my name is Kim... korean.. i don't speak & write English.. please understand my stupid language.. i want know.. preempt fuction on hsrp.. only preempt fuction working on hsrp tracking? please help..

shinwoo_acdc77 · ‎09-28-2006

i had seen EOBC error on Catalyst6509 i had replaced SUP1A ...but all module except SUP1A was reset .. and some module is not use... i expect a chassic problem... some % chassic problem...? please help me..

shinwoo_acdc77 · 07-08-2012

why different L2, L3 interface's input queue depth on same module ?1. switchcport mode access Portin...

shinwoo_acdc77 · 05-19-2010

thanks your reply..Yes.. under 144M... why not display 300Mbps ?notebook is ThinkPad X300... good PC...

shinwoo_acdc77 · 05-19-2010

why 144M on 1142 802.11N?1142 configurationdot11 ssid WPA2 authentication open authentication key-ma...

shinwoo_acdc77 · 03-29-2010

thank you... your reply....AP is enough.....and Client Driver all UpdateI think that auto-AP NO RRM ...

shinwoo_acdc77 · 03-29-2010

sorry!! i'm very busy...^^our all Client driver update, AP connect Radius(ACS)all fine..

shinwoo_acdc77 · 03-23-2010

hi. this is kimi have some questions!!! please helpmy customer use wireless network (controller base...

shinwoo_acdc77 · 08-17-2009

install hardwareWLC ACSAP1131WPA1+TKIP, H-REAPClient high frequently reconnect(roaming in APs), i th...

shinwoo_acdc77 · 03-23-2008

FWSM cpu high level (90%-100%) by periods..I think bug on 3.2(3) but not certainlyI found bug 1. tcp...

shinwoo_acdc77 · 02-29-2008

hi my name is kim.. i had installed FWSM3.2(3)+SUP720traffic is 1Gbps(in+out)but i founded FWSM abno...

shinwoo_acdc77 · 05-31-2007

topologyreal server : 2contents configurationowner test content web_service add service server1 add ...

shinwoo_acdc77 · 05-13-2007

shinwoo_acdc77 · 05-10-2007

why not nat translation ... i don't understand.. please help me==== config ====nat (inside1) 1 10.10...

shinwoo_acdc77 · 10-16-2006

hi.. my name is Kimshinwoo.. i will question DMVPN SA problem..topologyDMVPN HUB Routertunnel1(sourc...

shinwoo_acdc77 · 10-09-2006

hi.. my name is Kim... korean..i don't speak & write English..please understand my stupid language.....

shinwoo_acdc77 · 09-28-2006

i had seen EOBC error on Catalyst6509i had replaced SUP1A ...but all module except SUP1A was reset ....

Date Registered	‎09-21-2006 10:35 AM
Date Last Visited	‎08-18-2017 03:53 AM
Total Messages Posted	19

why different L2, L3 interface's input ...

Re: why AP1142 802.11N 144M?

why AP1142 802.11N 144M?

Re: wireless client disconnect from lig...

Re: wireless client disconnect from lig...

wireless client disconnect from lightwe...

WLC4404 client up/down issue

FWSM 3.2(3) bug? or different problem? ...

FWSM High CPU !!! version 3.2(3)

CSS sticky-srcip-dstport problem....

ASA two inside interface problem

ASA NAT problem... help me.

R-to-R DMVPN SA exchange Problem..

HSRP Preempt problem..~~~

Catalyst 6509 (SUP1A+MSFC2) EOBC Error

why different L2, L3 interface's input queue depth on same module ?