Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
jafrazie
‎06-10-2020
Cisco Employee
Recent Badges
Awards
Recent Badges
See all
CCP Member
100 Helpful Vote
15 Accepted Solution
1 Accepted Solution
5 Accepted Solution
30 Helpful Vote
10 Helpful Vote
1 Helpful Vote
50 Replies
20 Replies
Stats
Member since ‎05-01-2003
424
Posts
232
Helpful
22
Solutions

Re: wired 802.1x guest vlan test

Created by in Switching
05-09-2019
05-09-2019
multi-auth and multi-domain auth are not equal. This is not supported on the 3560: https://www.cisco...

Re: wired 802.1x guest vlan test

Created by in Switching
05-08-2019
05-08-2019
What code rev on the 3560 is this? Try to disable multi-auth: [no] authentication host-mode multi-au...

Re: wired 802.1x guest vlan test

Created by in Switching
05-07-2019
05-07-2019
Did you plug in the machine after you disabled 1X on it? With the config below, the switch will try ...

Re: 802.1x port config - monitoring mode to off

Created by in Network Access Control
04-25-2019
04-25-2019
[authentication port-control force-authorized] This will set 1X state-machine to force-authorized. 1...

Re: 802.1x port config - monitoring mode to off

Created by in Network Access Control
04-25-2019
04-25-2019
Do you mean something like this? https://community.cisco.com/t5/switching/setting-an-interface-back-...

Re: ISE: Reauthentication Timers

Created by in Network Access Control
02-27-2019
02-27-2019
Yes, with the config listed you have enabled re-auth, and told it to honor settings from AAA. It's s...

Re: Access-session host-mode option for an AP port

Created by in Network Access Control
02-27-2019
02-27-2019
If you are authenticating APs somehow, then single-auth will work when your design is CUWN. If this ...

Re: ISE 2.2 - Wired Guest with Dot1x enabled on Native supplicant

Created by in Network Access Control
02-26-2019
02-26-2019
Would also like to take a look at port config and/or what ISE is sending back for any timers for wha...

Re: Welcome to the DNA Center API Support Community!

Created by in Networking Blogs
08-09-2018
08-09-2018
Onboard a DNA Center, APIs are here: https:///dna/apidoc Or Gear icon (top right) --> API Documentat...

Re: Getting Started with NETCONF/YANG – Part 2

Created by in Networking Blogs
07-16-2018
07-16-2018
Hi Tymofiy. We will support the candidate config store in our next major release circa end of July. ...

Re: DNAC 1.1 API Authertication discusion

Created by in Cisco Digital Network Architecture (DNA)
03-22-2018
03-22-2018
Hi Pj:I see a domain coming back from sandboxdnac.cisco.com. Are you seeing it?Also, yes; we have a ...

Re: DNAC 1.1 API Authertication discusion

Created by in Cisco Digital Network Architecture (DNA)
03-01-2018
03-01-2018
Hi Da:There are 3 APIs here you might need:api/system/v1/auth/login — this logs in and DNAC will ret...

Cisco DNA Center APIs -- Initial Exploration

Created by in Networking Blogs
01-17-2018
01-17-2018
So what?Maybe you already have your own DNA Center. Maybe you're wondering how, or why to leverage t...

Welcome to the DNA Center API Support Community!

Created by in Networking Blogs
12-18-2017
12-18-2017
Please post any questions you have about using APIs on DNA Center. If you are facing an issue, pleas...

Re: How to list all YANG modules used by the RESTCONF server on IOS-XE/NX-OS/IOS-XR devices

Created by in Physical and Virtual Network Elements
10-13-2017
10-13-2017
Yes, the URIs above are for 16.6. This is RFC-8040 compliant. RESTCONF (in 16.6) only uses 443. RFC ...
Public Statistics
Date Registered ‎05-01-2003 03:03 PM
Date Last Visited ‎06-10-2020 10:51 AM
Total Messages Posted 424
Total Helpful Votes Received 232
Helpful Votes From
See all >