About promero

promero · 08-26-2024

Team, I have a virtual ISE (OVA extra small) version 3.3 patch 2 where the Application Server is stuck in "initializing", the strange thing is that it does operate and can be viewed through the GUI. I have performed the stop, start, restart procedure...

promero · 09-06-2021

Team,I want to implement a second WLC but for AP infrastructure reasons I cannot go beyond version 8.3.150 and it happens that this second WLC is with version 8.5.151 but when performing a downgrade it gives me an error of "TFTP code file type not su...

promero · 04-05-2021

Team,I have a problem, I want to connect a PC and a Polycom phone but the PC does not authenticate to ISE.By having the PC connected to the phone, the ISE recognizes it by MAB and it should be by DOT1X.When doing tests, I connect the PC directly to t...

promero · 08-19-2020

Team,I have an AP 2702i that was factory reset and when I connect it to vWLC 8.5.161.0 it cannot register. Attached logg of the AP, has anyone seen this error ?. AP500f.8094.85a0#*Aug 19 19:19:37.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Ale...

promero · 07-21-2019

Hello, I must perform a migration from a 3com switch to catalys 9200 but the 3com has MSTP. The query is, can Rapid-PVST be compatible with MSTP? or MSTP with MSTP is recommended. 3com MSTP has the entire vlan in instance 0. [3COM-Distribution]displa...

promero · 09-05-2024

I finally found the solution with TAC support, the problem is because Esxi version 7.0.0 is not compatible with ISE 3.3, you must use Esxi version 7.0.3 onwards. https://www.cisco.com/c/en/us/td/docs/security/ise/3-3/compatibility_doc/b_ise_sdt_33.ht...

promero · 08-28-2024

I installed the Small version and it has the same symptom, the Application Server is in the initialization state but it allows you to enter the GUI and configure, it enables the TACACs service and it works, I leave screenshots. I will review with ano...

promero · 08-27-2024

Thanks for the information, I'm going to try the Small version. Previously in Esxi 8 I installed the "Eval" ISE, the "Extra Small" had not been installed. I installed patch 2 from the GUI even when it was in the "initializing" state, that is very str...

promero · 08-27-2024

Extra Small but I have licenses (I haven't registered it yet) 1 node standalone Change Esxi from version 8 to 7.0, In 8 it worked without problems Snapshots disabled Patch installed from GUI, even with the Application Server in initializing state ...

promero · 09-07-2021

I just took the WLC to a factory reset, I started it with the 8.3.122 image and repeated the upgrade process which now turned out to be successful. Thanks for the support and feedback.

Member Since	‎05-02-2019 08:16 AM
Date Last Visited	‎09-17-2024 02:33 AM
Posts	25
Total Helpful Votes Received	10

User Statistics

User Activity

Application Server state "initializing" but if it works

Downgrade ios from 8.5.151 to 8.3.150 or upgrade 8.3.122 to 8.3.150

PC authentication with dot1x and IP Phone with MAB

AP no joint vWLC

Rapid-PVST+ with MSTP

Re: Application Server state "initializing" but if it works

Re: Application Server state "initializing" but if it works

Re: Application Server state "initializing" but if it works

Re: Application Server state "initializing" but if it works

Re: Downgrade ios from 8.5.151 to 8.3.150 or upgrade 8.3.122 to 8.3.15