Callmanager 8.0.2 setup on a VM VirtualBox

morenike1_2 · ‎07-31-2011

I try to set up the callmanager on VM Virtualbox Manager and l am confronted with this error message when the callmanager was booting in up. Can someone give me a hand to the solution to this problem pls.

Checking device /device /dev/dev6

fsck 1.41.4 (27-Jan-2009)

Possibly non-existment or swap device?

ERRORS found (8)

Mounting partition /mnt/part1

Mounting partition /mnt/part2

Mounting partition /mnt/part3

Mounting partition /mnt/part6

*******************************************************************************************************************************************************************************

****** Welcome to Cisco Unifide communications Recovery Disk

Version 8.0.2.40000-1

copyright - Cisco System, Inc. 2006-2009

No CM image found on the hard drive

Please enter one of the following options:

[W] windows pre-installation setup

[F] check and correct disk file systems.

[V] verify the disk partitioning layout.

[A] Alighn partitions on disks.

[Q] Quit this recovery disk program

Adrian Saavedra · ‎08-01-2011

Hi,

You're using the wrong DVD. You are using a recovery disc. You need the installation media.

Hope it helps, please rate if it does.

Adrian.

Sent from Cisco Technical Support iPhone App

morenike1_2 · ‎09-11-2011

Hi

I have got my lab setup with router 2620XM, 2950 switch, 4 ip phones 7960. The ip phones are ringing each other with the switch and router that l have set up in my lab. I have set up my callmanager 8.0(2C) which am able to open the home page for the administration, OS, servicabilty etc. I have connected the callmanager to the network which it can ping the the switch and the router using utilis network ping x.x.x.x to make sure that there is a connection. I have enabled the dhcp on the callmanager under the sytem, dhcp sever, dhcp subnet, maybe l need more info to enter which am not sure. I have also actived the dhcp monitor service. But the problem that l have is that when l power up the ip phones, it could not load the software from the callmanger to the phones to make the callmanager take control of the VOIP network that l set up. But ip phones is loading up the Vlan and loading the firmware from the flash of the router without the callmanger. Pls l need some help.

Aaron Harrison · ‎09-11-2011

Hi

Option 150 on the DHCP server determines where the phone downloads firmware and configuration from. You should have this set to your CUCM IP address.

In your phone network settings, you should see 'TFTP Server 1' contains the CUCM address if you have done this correctly.

Regards

Aaron

Please rate helpful posts...

Aaron Please remember to rate helpful posts to identify useful responses, and mark 'Answered' if appropriate!

morenike1_2 · ‎09-12-2011

Hi

that is the config on my router. The phone is yet to register.

Router#sh run

Building configuration...

Current configuration : 1883 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

no aaa new-model

!

resource policy

!

no network-clock-participate slot 1

no network-clock-participate wic 0

ip cef

!

no ip dhcp use vrf connected

ip dhcp excluded-address 20.20.20.1

20.20.20.10

ip dhcp excluded-address 30.30.30.1

30.30.30.10

ip dhcp excluded-address 192.168.1.1

192.168.1.10

!

ip dhcp pool DATA

network 192.168.1.0 255.255.255.0

default-router 192.168.1.1

option 150 ip 192.168.1.10

lease 5

!

ip dhcp pool VOICE

network 30.30.30.0 255.255.255.0

option 150 ip 192.168.1.10

default-router 30.30.30.1

lease 5

!

controller E1 0/1

!

interface FastEthernet0/0

no

ip address

duplex auto

speed auto

!

interface FastEthernet0/0.1

encapsulation dot1Q 1 native

ip

address 20.20.20.1 255.255.255.0

!

interface FastEthernet0/0.5

encapsulation dot1Q 5

ip

address 30.30.30.1 255.255.255.0

ip

helper-address 192.168.1.1

!

interface FastEthernet0/0.10

encapsulation dot1Q 10

ip

address 192.168.1.1 255.255.255.0

!

ip http server

ip http authentication local

no ip http secure-server

ip http path flash:

!

telephony-service

max-ephones 5

max-dn 5

ip

source-address 30.30.30.1 port 2000

max-conferences 4 gain -6

web

admin system name ojay password cisco1

dn-webedit

transfer-system full-consult

!

ephone-dn

1 dual-line

number 2000

!

ephone-dn

2 dual-line

number 2001

!

ephone

1

device-security-mode none

mac-address 0014.6AC3.C745

button

1:1

!

ephone

2

device-security-mode none

mac-address 0014.6A87.8E91

button

1:2

end

Network Configuration on the IP Phone 7960

DHCP SERVER

30.30.30.1

MAC Address

00065356AC62

Host Name SEP00065356AC92

IP Address 30.30.30.12

Subnet Mask 255.255.255.0

TFTP Server 1 192.168.1.10

Default Router 1

Operational

Vlan Id 5

Callmanager

1 192.168.1.10

Date: Mon, 12 Sep 2011 00:37:29 -0600

From: supportforums-donotreply@jivesoftware.com

To: oojuribiodun@hotmail.com

Subject: - Re: Callmanager 8.0.2 setup on a VM VirtualBox

Cisco Support Community

Re: Callmanager 8.0.2 setup on a VM VirtualBox

created by aaronharrison in Voice over IP - View the full discussion

Hi Option 150 on the DHCP server determines where the phone downloads firmware and configuration from. You should have this set to your CUCM IP address. In your phone network settings, you should see 'TFTP Server 1' contains the CUCM address if you have done this correctly. Regards Aaron Please rate helpful posts...

Reply to this message by going to Cisco Support Community

Start a new discussion in Voice over IP at Cisco Support Community

morenike1_2 · ‎09-12-2011

Hi

the ip phone is not registered

ephone-1 Mac:0014.6AC3.C745 TCP socket:[-1]

activeLine:0 UNREGISTERED

mediaActive:0 offhook:0 ringing:0 reset:0

reset_sent:0 paging 0 debug:0 caps:0

IP:0.0.0.0 0 Unknown 0 keepalive 0 max_line 0

ephone-2 Mac:0014.6A87.8E91 TCP socket:[-1]