11-03-2004 11:33 PM
I have configured a 1760 as SIP gateway but there is a problem registering to the registrar server.
I used a sniffer but I didn't see any registration requests.
This is my conf.
version 12.2
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
!
hostname cisco1760
!
boot system flash flash:c1700-sv8y-mz.122-15.ZJ5.bin
logging exception 16342
logging count
logging queue-limit 100
logging buffered 16342 debugging
no logging console
enable secret 5 <removed>
!
username marinos privilege 15 secret 5 <removed>
username panos* privilege 15 secret 5 <removed>
username souroutiss privilege 15 secret 5 <removed>
username tolzer privilege 15 secret 5 <removed>
username surpass privilege 0 secret 5 <removed>
memory-size iomem 15
clock timezone EET 2
clock summer-time EET recurring last Sun Mar 3:00 last Sun Oct 4:00
tdm clock E1 1/0 both import onboard internal
aaa new-model
!
!
aaa authentication login default local
aaa authorization exec default local if-authenticated
aaa session-id common
ip subnet-zero
!
!
no ip domain lookup
!
no ip bootp server
ip cef
!
isdn switch-type primary-net5
!
voice call send-alert
!
voice service voip
sip
!
!
!
!
!
!
!
no voice hpi capture buffer
no voice hpi capture destination
!
!
mta receive maximum-recipients 0
!
!
controller E1 1/0
pri-group timeslots 1-31
!
!
interface FastEthernet0/0
ip address 172.25.32.17 255.255.224.0
speed auto
!
interface Serial1/0:15
no ip address
no logging event link-status
isdn switch-type primary-net5
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.25.32.100
no ip http server
ip pim ssm default
!
!
!
logging trap notifications
!
snmp-server community <removed> RO
snmp-server enable traps tty
radius-server authorization permit missing Service-Type
call rsvp-sync
!
voice-port 0/0
cptone GR
!
voice-port 0/1
cptone GR
!
voice-port 1/0:15
cptone GR
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 10 pots
application session
destination-pattern 0030898
direct-inward-dial
port 1/0:15
forward-digits all
!
dial-peer voice 30 voip
application session
destination-pattern 0030671......
session protocol sipv2
session target sip-server
dtmf-relay sip-notify
codec g711alaw
no vad
!
dial-peer voice 5 pots
application session
destination-pattern 0898
direct-inward-dial
port 0/0
forward-digits all
!
dial-peer voice 20 voip
application session
destination-pattern 07....
session protocol sipv2
session target sip-server
dtmf-relay sip-notify
codec g711alaw
no vad
!
sip-ua
retry invite 5
retry response 3
retry bye 2
retry cancel 2
registrar ipv4:172.25.32.68 expires 3600
sip-server ipv4:172.25.32.68
!
banner motd ^C
************************************************
* *
* 1760 Cisco Router *
* Gateway Router *
* *
************************************************
^C
privilege exec level 0 traceroute ip
privilege exec level 0 traceroute
privilege exec level 0 ping ip
privilege exec level 0 ping
privilege exec level 1 enable
privilege exec level 0 show ip route
privilege exec level 0 show ip interface
privilege exec level 0 show ip
privilege exec level 0 show version
privilege exec level 0 show interfaces
privilege exec level 0 show
!
line con 0
password 7 <removed>
line aux 0
line vty 0 4
password 7 <removed>
!
ntp clock-period 17207946
ntp server 192.168.200.200
end
11-04-2004 01:23 AM
The registrar functions here is to register e.164 numbers on behalf of analog phones voice ports (FXS).
I wonder what is the voice-port 0/0 and 0/1
Thanks
SSng
11-04-2004 01:59 AM
SIP gateways allow registration of E.164 numbers to a SIP proxy or registrar server on behalf of analog telephone voice ports (FXS), IP phone virtual voice ports (EFXS), and local SCCP phones.
Yes ports 0/0 and 0/1 are FXS ports.
As you can see in dial-peer voice 5 pots I use the FXS 0/0 port.
I actually saw a registration request for the FXS but not successful.
I did a little research and I think that the problem is the telephone number:
0030898 works fine
+30898 doesn't work.
error 404 NOT FOUND.
I thing I have a problem with the "+"
Any help here ?
11-05-2004 11:13 PM
Can you run debug ccsip messages
You should be able to see registration process and what's the different between the two numbers
Thanks
SSng
11-07-2004 10:51 PM
The numbers seems to be the same but still I have this message:
Status: 501 Third party registration is not supported.
Anyway, I found a way to configure router 1760 as "trusted" in the registrar server, and this way no registration or authentication is required.
Thanks for your help
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide