12-05-2010 06:13 AM
I have tested VWIC-2MFT-E1 card in 2651XM and 1760-V gateways. In all voice platforms and IOS got Layer 1 DEACTIVATED status. The far end - is the own Cisco E1 gateways or/and E1 PCI cards. The cross E1 patch cord between E1 gateways used with 1-2==4-5 pinout scheme, the status of LED on CD is green, when patch cord connected.
Was changed many combinations with clock Source line and internal - no result.
Router#sh contr e1
E1 0/0 is down.
Applique type is Channelized E1 - balanced
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20060927, FPGA: 20, spm_count = 16356
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (0 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Router#sh isdn status
Global ISDN Switchtype = primary-net5
ISDN Serial0/0:15 interface
dsl 1, interface ISDN Switchtype = primary-net5
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 1 CCBs = 0
The Free Channel Mask: 0x00000000
Number of L2 Discards = 0, L2 Session ID = 1
Router#sh int se0/0:15
Serial0/0:15 is down, line protocol is down
Hardware is DSX1
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Last input 00:00:04, output never, output hang never
Last clearing of "show interface" counters 16:00:00
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
25580 packets input, 76740 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Below was explained input packets counter:
when debug isdn q921 detail enabled, we can see ERROR messages
*Apr 16 05:12:01.260: ISDN Q921d: isdn_from_driver_process: QUEUE_EVENT
*Apr 16 05:12:01.260: ISDN Se0/0:15 **ERROR**: process_rxdata: frame recieved while Interface is down
*Apr 16 05:12:01.260: ISDN Q921d: isdn_from_driver_process: event_count 1
*Apr 16 05:12:02.258: ISDN Q921d: isdn_from_driver_process: QUEUE_EVENT
*Apr 16 05:12:02.262: ISDN Se0/0:15 **ERROR**: process_rxdata: frame recieved while Interface is down
*Apr 16 05:12:02.262: ISDN Q921d: isdn_from_driver_process: event_count 1deb
In configure mode interface Serial0/0:15 no shut has no effect, interface still down.
show diag command output:
WIC/VIC Slot 0:
E1 DI (2 port) Multi-Flex Trunk WAN daughter card
Hardware revision 1.0 Board revision B0
Serial number 0034244586 Part number 800-04479-03
FRU Part Number VWIC-2MFT-E1-DI=
Test history 0x00 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 25 01 00 02 0A 87 EA 50 11 7F 03 00 00 00 00
0x30: 58 00 00 00 02 09 13 00 FF FF FF FF FF FF FF FF
12-07-2010 08:05 AM
Hi,
You will need an E1 cross over to connect two cisco's together
1 - 4
2 - 5
3 - NU
4 - 1
5 - 2
6 - NU
7 - NU
8 - NU
NU = Not Used
and then you'll need to configure one end as the isdn switch, using the 'isdn emulate network' configuration on the serial :15 interface
Adam
12-07-2010 08:17 AM
Adam,
I have wrote in the start of message: The cross E1 patch cord between E1 gateways used with 1-2==4-5 pinout scheme
And, when I connect the same cross E1 patch cord to 1760-V with VWIC-MFT-E1 (1-port) card - the status of controller e1 immediately UP, and Layer 1 is ACTIVE.
The far end (E1 PCI card) in my server on the same table have proto network option, and Cisco gateway with
VWIC-2MFT-E1-DI emulate user (cpe) option.
I have tested with isdn protocol-emulate network and cpe options.
12-07-2010 09:39 AM
I understand now that your problem is with the 2650, and that it's OK in the 1700.
This is odd. some platforms require the setting up of the E1 card, before some of the configuration appears -
eg card type e1 0 0, but it seams that you already have access to the controller settings !!??!
12-07-2010 09:57 AM
Thank you for response, Adam.
No, I haven't problem with 2651XM, I have problem with VWIC-2MFT-E1-DI only.
Several combinations was made with the same simptomatic,
a. 1760-V with VWIC-2MFT-E1-DI doesn't work
b. 1760-V with VWIC-MFT-E1 working perfect
c. 2651XM with VWIC-2MFT-E1-DI doesn't work
d. 2651XM with VWIC-MFT-E1 working perfect
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide