02-09-2012 08:29 AM
Hello
Please, help me with my problem
Can't connect and get IP address via GPRS
I read many articles about this problem but can't solve it.
Config
!
chat-script gsm "" AT OK AT&F OK "AT\\Q3" OK "AT+CGDCONT=1,IP,www.umc.ua" OK "ATD*99***1#" TIMEOUT 30 CONNECT
chat-script reset "" \d\d\d+++\d\d\d
!
interface Async1
description gsm
ip address negotiated
encapsulation ppp
load-interval 30
dialer in-band
dialer string "*99***1#" modem-script gsm
dialer-group 1
async mode dedicated
ppp authentication pap chap callin
ppp chap password 0 igprs
ppp pap sent-username igprs password 0 igprs
!
dialer-list 1 protocol ip permit
!
line aux 0
script dialer gsm
script reset reset
modem InOut
exec-character-bits 8
special-character-bits 8
no exec
transport input all
escape-character BREAK
stopbits 1
speed 115200
flowcontrol hardware
!
Log
*08:59:33.523: CHAT1: Chat script reset finished, status = Success
*08:59:33.523: TTY1: Modem: HANGUP->HANGUP
*08:59:33.523: TTY1: no timer type 0 to destroy
*08:59:33.523: TTY1: no timer type 1 to destroy
*08:59:33.523: TTY1: no timer type 3 to destroy
*08:59:33.523: TTY1: no timer type 4 to destroy
*08:59:33.523: TTY1: no timer type 10 to destroy
*08:59:33.523: TTY1: no timer type 2 to destroy
*08:59:33.823: TTY1: dropping DTR, hanging up
*08:59:33.823: TTY1: Set DTR to 0
*08:59:33.823: tty1: Modem: HANGUP->IDLE
*08:59:38.827: TTY1: restoring DTR
*08:59:38.827: TTY1: Set DTR to 1
*08:59:39.827: TTY1: DSR came up
*08:59:39.827: TTY1: no timer type 1 to destroy
*08:59:39.827: TTY1: no timer type 0 to destroy
*08:59:39.827: TTY1: no timer type 2 to destroy
*08:59:39.827: tty1: Modem: IDLE->(unknown)
*08:59:41.827: %LINK-3-UPDOWN: Interface Async1, changed state to up
*08:59:41.827: As1 DDR: Dialer statechange to up
*08:59:41.827: As1 DDR: Dialer received incoming call from *99***1#
*08:59:41.827: As1 PPP: Using dialer call direction
*08:59:41.827: As1 PPP: Treating connection as a callin
*08:59:41.827: As1 PPP: Session handle[FF00000B] Session id[6]
*08:59:41.827: As1 PPP: Phase is ESTABLISHING, Passive Open
*08:59:41.827: As1 LCP: State is Listen
*08:59:43.811: As1 LCP: TIMEout: State Listen
*08:59:43.811: As1 PPP: Authorization required
*08:59:43.811: As1 LCP: O CONFREQ [Listen] id 51 len 24
*08:59:43.811: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:43.811: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:43.811: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:43.811: As1 LCP: PFC (0x0702)
*08:59:43.811: As1 LCP: ACFC (0x0802)
*08:59:45.827: As1 LCP: TIMEout: State REQsent
*08:59:45.827: As1 LCP: O CONFREQ [REQsent] id 52 len 24
*08:59:45.827: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:45.827: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:45.827: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:45.827: As1 LCP: PFC (0x0702)
*08:59:45.827: As1 LCP: ACFC (0x0802)
*08:59:47.843: As1 LCP: TIMEout: State REQsent
*08:59:47.843: As1 LCP: O CONFREQ [REQsent] id 53 len 24
*08:59:47.843: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:47.843: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:47.843: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:47.843: As1 LCP: PFC (0x0702)
*08:59:47.843: As1 LCP: ACFC (0x0802)
*08:59:48.827: TTY3: timer type 1 expired
*08:59:48.827: TTY3: Exec timer (continued)
*08:59:49.859: As1 LCP: TIMEout: State REQsent
*08:59:49.859: As1 LCP: O CONFREQ [REQsent] id 54 len 24
*08:59:49.859: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:49.859: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:49.859: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:49.859: As1 LCP: PFC (0x0702)
*08:59:49.859: As1 LCP: ACFC (0x0802)
*08:59:51.875: As1 LCP: TIMEout: State REQsent
*08:59:51.875: As1 LCP: O CONFREQ [REQsent] id 55 len 24
*08:59:51.875: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:51.875: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:51.875: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:51.875: As1 LCP: PFC (0x0702)
*08:59:51.875: As1 LCP: ACFC (0x0802)
*08:59:53.891: As1 LCP: TIMEout: State REQsent
*08:59:53.891: As1 LCP: O CONFREQ [REQsent] id 56 len 24
*08:59:53.891: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:53.891: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:53.891: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:53.891: As1 LCP: PFC (0x0702)
*08:59:53.891: As1 LCP: ACFC (0x0802)
*08:59:55.907: As1 LCP: TIMEout: State REQsent
*08:59:55.907: As1 LCP: O CONFREQ [REQsent] id 57 len 24
*08:59:55.907: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:55.907: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:55.907: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:55.907: As1 LCP: PFC (0x0702)
*08:59:55.907: As1 LCP: ACFC (0x0802)
*08:59:57.923: As1 LCP: TIMEout: State REQsent
*08:59:57.923: As1 LCP: O CONFREQ [REQsent] id 58 len 24
*08:59:57.923: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:57.923: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:57.923: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:57.923: As1 LCP: PFC (0x0702)
*08:59:57.923: As1 LCP: ACFC (0x0802)
*08:59:59.939: As1 LCP: TIMEout: State REQsent
*08:59:59.939: As1 LCP: O CONFREQ [REQsent] id 59 len 24
*08:59:59.939: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*08:59:59.939: As1 LCP: AuthProto PAP (0x0304C023)
*08:59:59.939: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*08:59:59.939: As1 LCP: PFC (0x0702)
*08:59:59.939: As1 LCP: ACFC (0x0802)
*09:00:01.955: As1 LCP: TIMEout: State REQsent
*09:00:01.955: As1 LCP: O CONFREQ [REQsent] id 60 len 24
*09:00:01.955: As1 LCP: ACCM 0x000A0000 (0x0206000A0000)
*09:00:01.955: As1 LCP: AuthProto PAP (0x0304C023)
*09:00:01.955: As1 LCP: MagicNumber 0x239BF33D (0x0506239BF33D)
*09:00:01.955: As1 LCP: PFC (0x0702)
*09:00:01.955: As1 LCP: ACFC (0x0802)
*09:00:03.971: As1 LCP: TIMEout: State REQsent
*09:00:03.971: TTY1: Async Int reset: Dropping DTR
*09:00:03.971: TTY1: Set DTR to 0
*09:00:03.971: As1 LCP: State is Listen
*09:00:05.971: %LINK-5-CHANGED: Interface Async1, changed state to reset
*09:00:05.971: As1 PPP: Sending Acct Event[Down] id[14]
*09:00:05.971: As1 LCP: State is Closed
*09:00:05.971: As1 PPP: Phase is DOWN
*09:00:08.971: TTY1: no timer type 0 to destroy
*09:00:08.971: TTY1: no timer type 1 to destroy
*09:00:08.971: TTY1: no timer type 3 to destroy
*09:00:08.971: TTY1: no timer type 4 to destroy
*09:00:08.971: TTY1: no timer type 10 to destroy
*09:00:08.971: TTY1: no timer type 2 to destroy
*09:00:08.971: Async1: asking modem_process to hangup TTY1
*09:00:08.971: CHAT1: Attempting line reset script
*09:00:08.971: CHAT1: Matched chat script reset to string reset
*09:00:08.971: CHAT1: Asserting DTR
*09:00:08.971: TTY1: Set DTR to 1
*09:00:08.971: CHAT1: Chat script reset started
*09:00:08.971: CHAT1: Sending string: \d\d\d+++\d\d\d
*09:00:10.971: %LINK-3-UPDOWN: Interface Async1, changed state to down
It seems that only incoming trafic are allowed.
Why don't modem call number?
Thanks
02-12-2012 10:39 AM
Hi! Did you defined your APN? I've posted blogpost here about grps connection on 880 router, maybe you will find it helpful http://betep.wpl.ru
Sent from Cisco Technical Support iPhone App
02-13-2012 03:31 AM
Hi!
Thanks for your attention
I define APN in chat-script gsm but cisco don't use it as you see in log.
If I start chat-script gsm manually it performed well but situation is still the same, I can't get IP address.
02-13-2012 03:37 AM
Did you try this one:
cellular 0 gsm profile create 1 www.umc.ua pap
Are you shure about dialed digits?
I can't see where you specified your login and password.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide