em 03-11-2013 10:30 PM
Hi,
After configuring Cisco Easy VPN Server I was able to form connection between client and VPN Server. But still I am not able to ping the LAN IPs. I am using NAT and I have removed VPN client network from NATing.
IP address I am trying to ping is 10.0.0.2.
Below is the configuration.
crypto ctcp
!
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
!
crypto isakmp client configuration group imovation
key ********
pool SDM_POOL_1
acl 100
crypto isakmp profile ciscocp-ike-profile-1
match identity group imovation
client authentication list ciscocp_vpn_xauth_ml_1
isakmp authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-template 1
!
ip local pool SDM_POOL_1 172.16.11.2 172.16.11.10
!
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
!
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA
set isakmp-profile ciscocp-ike-profile-1
!
!
!
!
!
!
interface Loopback0
ip address 172.16.1.1 255.255.255.0
!
interface GigabitEthernet0/1
description ### LAN ###
ip address 10.0.0.1 255.255.255.0
no ip unreachables
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface Virtual-Template1 type tunnel
ip unnumbered Loopback0
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
!
ip nat inside source list 101 interface Dialer1 overload
access-list 100 remark CCP_ACL Category=4
access-list 100 permit ip 10.0.0.0 0.0.0.255 any
access-list 101 deny ip 10.0.0.0 0.0.0.255 172.16.11.0 0.0.0.255
access-list 101 permit ip 10.0.0.0 0.0.0.255 any
access-list 101 permit ip 192.168.1.0 0.0.0.255 any
Pls help.
Thanks in advance.
em 03-12-2013 12:14 AM
Kindly TurnOff windows Firewall.
Also check
172.16.11.x when assigned check its netmaks by using ipconfig/all.
*** Do Rate All Helpful Posts***
em 03-12-2013 12:46 AM
Hi Jawad,
Firewall is already off. I checked the netmask it was /16 and I have done the necessary changes. Now it is /24 but it still not working.
em 03-12-2013 03:34 AM
What Default Gateway of
10.0.0.2..
em 03-12-2013 03:57 AM
it is 10.0.0.1 (Router Interface). I have created a loopback ip in the router and i cant ping that ip too.
em 03-12-2013 12:24 PM
Have you defined default route in your router config.
em 03-12-2013 08:27 PM
Yes. It is "ip route 0.0.0.0 0.0.0.0 Dialer1"
em 03-12-2013 10:28 PM
Hi,
Can you ping the internal IP address of the Router (10.0.0.1)?
Thanks.
Portu.
em 03-12-2013 11:54 PM
crypto isakmp client configuration group imovation
key ********
pool SDM_POOL_1
no acl 100
Check by Removing ACL
and also in your PC add manual Routes 172.16.11.0.
also post
route print of your PC
em 03-13-2013 01:35 AM
no. I cannot ping 10.0.0.1 ip either.
Descubra e salve suas ideias favoritas. Volte para ver respostas de especialistas, passo a passo, tópicos recentes e muito mais.
Novo por aqui? Comece com estas dicas. Como usar a Comunidade Guia do novo membro