02-20-2005 11:45 PM
I have a PRI to accept analog calls, it works fine
now I want to make the PRI to accept Digital Calls
this is my config my Router cisco 3662
interface Group-Async1
description connected tp Dial-in pcs (Analog)
ip unnumbered FastEthernet0/0
no ip directed-broadcast
encapsulation ppp
no ip split-horizon
dialer in-band
dialer idle-timeout 3600
dialer-group 2
async mode interactive
peer default ip address pool cisco3662-group-2
no fair-queue
ppp authentication chap pap callin g1
group-range 161 190
!
interface Serial2/0:15
no ip address
no ip directed-broadcast
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice modem
isdn guard-timer 3000
fair-queue 64 256 0
ppp authentication chap pap g1
ppp authorization g1
when the user dial in from digital I see the
following in my debugs
Router#
2w5d: %LINK-3-UPDOWN: Interface Serial2/0:0, changed state to up
2w5d: Se2/0:0 PPP: Treating connection as a callin
2w5d: Se2/0:0 PPP: Phase is ESTABLISHING, Passive Open
2w5d: Se2/0:0 LCP: State is Listen
2w5d: Se2/0:0 LCP: I CONFREQ [Listen] id 85 len 6
2w5d: Se2/0:0 LCP: VendorSpecific OUI (0x0002)
2w5d: Se2/0:0 LCP: O CONFREQ [Listen] id 1 len 15
2w5d: Se2/0:0 LCP: AuthProto CHAP (0x0305C22305)
2w5d: Se2/0:0 LCP: MagicNumber 0x66A10E2A (0x050666A10E2A)
2w5d: Se2/0:0 LCP: O CONFREJ [Listen] id 85 len 6
2w5d: Se2/0:0 LCP: VendorSpecific OUI (0x0002)
2w5d: Se2/0:0 LCP: TIMEout: State REQsent
2w5d: Se2/0:0 LCP: O CONFREQ [REQsent] id 2 len 15
2w5d: Se2/0:0 LCP: AuthProto CHAP (0x0305C22305)
2w5d: Se2/0:0 LCP: MagicNumber 0x66A10E2A (0x050666A10E2A)
2w5d: Se2/0:0 LCP: I CONFACK [REQsent] id 2 len 15
2w5d: Se2/0:0 LCP: AuthProto CHAP (0x0305C22305)
2w5d: Se2/0:0 LCP: MagicNumber 0x66A10E2A (0x050666A10E2A)
2w5d: Se2/0:0 LCP: I CONFREQ [ACKrcvd] id 2 len 13
2w5d: Se2/0:0 LCP: MagicNumber 0x303005F3 (0x0506303005F3)
2w5d: Se2/0:0 LCP: Callback 6 (0x0D0306)
2w5d: Se2/0:0 LCP: O CONFREJ [ACKrcvd] id 2 len 7
2w5d: Se2/0:0 LCP: Callback 6 (0x0D0306)
2w5d: Se2/0:0 LCP: I CONFREQ [ACKrcvd] id 3 len 10
2w5d: Se2/0:0 LCP: MagicNumber 0x303005F3 (0x0506303005F3)
2w5d: Se2/0:0 LCP: O CONFACK [ACKrcvd] id 3 len 10
2w5d: Se2/0:0 LCP: MagicNumber 0x303005F3 (0x0506303005F3)
2w5d: Se2/0:0 LCP: State is Open
2w5d: Se2/0:0 PPP: Phase is AUTHENTICATING, by this end
2w5d: Se2/0:0 CHAP: O CHALLENGE id 1 len 27 from "Router"
2w5d: Se2/0:0 LCP: I IDENTIFY [Open] id 4 len 18 magic 0x303005F3 MSRASV5.00
2w5d: Se2/0:0 LCP: I IDENTIFY [Open] id 5 len 21 magic 0x303005F3 MSRAS-1-PCNAME 2w5d: Se2/0:0 CHAP: I RESPONSE id 1 len 25 from "mall"
2w5d: Se2/0:0 CHAP: O FAILURE id 1 len 24 msg is "Authorization failed"
2w5d: Se2/0:0 PPP: Phase is TERMINATING
2w5d: Se2/0:0 LCP: O TERMREQ [Open] id 3 len 4
2w5d: %ISDN-6-DISCONNECT: Interface Serial2/0:0 disconnected from 1234567890 , call lasted 3 seconds
2w5d: %LINK-3-UPDOWN: Interface Serial2/0:0, changed state to down
2w5d: Se2/0:0 LCP: State is Closed
2w5d: Se2/0:0 PPP: Phase is DOWN
Any Input in this issue.
Thanks
02-22-2005 08:41 AM
Looks like the dialin client is not configured for any authentication (pap or chap etc). So either you remove the ppp authentication commands under the interface serial 2/0:15 or configure the client for that.
Also you need to add some commands under the interface serial2/0:15..it should look like
interface serial 2/0:15
ip unnumbered FastEthernet0/0
no ip directed-broadcast
encapsulation ppp
dialer in-band
dialer idle-timeout 3600
dialer-group 2
peer default ip address pool cisco3662-group-2
ppp authentication chap pap g1
!
Test it after that..post the debugs if it doesn't work
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide